I am going to purchase SF 300 24p POE Switch and if this Switch supports the configuration via console? As i have ESW-500 Series switches and it does not support console.
View 4 RepliesOn a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies View RelatedMy company just bought a SF300-24P, got it configured without much issue. Today I try to get into it and I can't. Tried via HTTP and console and nothing happens. Decided to try to reset it using the button on the front. Using the documentation, I held down the button for over 10 seconds. Didn't reset to factory defaults, tried again and rebooted it, still nothing. What I am I doing wrong. Also nothing comes up on console window and I'm using the setting for Hyper Terminal that the documentation says I should use.
View 5 Replies View RelatedI have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies View RelatedOur company lost a switch and replaced it with a SF300-24. The other components are a Westell modem and an Amped Wireless R10000G router.
The current configuration has the Westell DLS modem going into the R10000G router, the router is the DHCP server and from there it is plugged into port 1 of the switch (DHCP is off on the switch).
So the problem is the computers on the network randomly drop off the network during the day and sometimes upon booting them up in the morning won't even see the local network. If I unplug the R10000G and then plug back in that fix's the problem for a few hours but then sooner or later the computers randomly drop off.
There is one network printer set to a static IP address. It never seems to have an issue. I have tried setting some of the computers to static but they still have connection issues at some point.
I am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies View RelatedI am using a Cisco SRP527W router for our small business. As this device only has 4 LAN ports I want to add another switch so as our business grows I can add more PCs and VoIP phones. I would like to use a Cisco SF300-24 switch and before I purchase am interested to know if anyone has used a SRP527W router with this range of Cisco switches. Are there any compatibility issues or will these two devices work well together?
View 6 Replies View RelatedIs it possible to trunk a SF300 switch with a 3750 switch? If so how? Whenever I turn trunking on the 3750 port I lose connection to the SF300.
View 5 Replies View RelatedHow about supporting an scp server on the switch? Makes life much easier for collecting configs and pushing OS upgrades.
View 1 Replies View RelatedI have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies View Relatedi have a customer that will use this switch model.I was wondering if there is any recommendation from like an AS-BU for the most appropriate software version and what would be ?
View 4 Replies View RelatedI need to confirm how many queues actually supports the switch SG500X?. In SG500X_data_sheet.pdf document (pg. 8) say they have 4 hardware queues (8 future) !
View 2 Replies View RelatedHow to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address) isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address)isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
We are having a problem with our ACS and switch configuration.Basically if the switches lose connectivity to the ACS server the switches completely lock up, you can’t even console onto the switches.We want them to use the fall back username and password when this happens.
View 1 Replies View RelatedI can access the web console, and also have telnet access but only to a VT100 menu system - How do I access the full console command prompt (without using the serial console connection)?
View 4 Replies View RelatedI can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures. The Hyper Terminal settings. Error:
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
I have had the switch for about 2 years and recently moved. The manual specifies:
38400 bps and 8-n-1 serial port settings using DB9F to DB9F cable.
I have done this and tried using multiple machines/ports/cables as well as several peices of software (minicom, PuTTy, hyperterminal) and none give me any output from the switch at all.
The trouble is that in its original config, it had 1 port locked into its own VLAN for management with port security and an obscure RFC1918 IP address which I cannot recall for the life of me.
At this point, I have no access to TCP/IP management so serial console is my last hope and is not working.
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedI'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedI am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View Relatedhow to configure a server with net gear switch . I want to restrict access for a few users and use the netgear switch for file sharing between the small network. its got auto configuration .
View 3 Replies View RelatedI have a new install with 3 SF300 switches, setup as vlan 2, the switch connected directly to the 2901 router has no problems, plug in a phone and it gets an IP, but if connected to either of the two swtiches behind the first switch, they do not get an IP. I am seeing the DHCP request hitting the router, and the router sending the IP to the phone, but it never gets the IP.
*Jun 15 10:40:20.040: DHCPD: client's VPN is .
*Jun 15 10:40:20.040: DHCPD: Sending notification of DISCOVER:
*Jun 15 10:40:20.040: DHCPD: htype 1 chaddr 40f4.ecef.bded
[Code]....
All ports are setup as trunk on vlan 2 including the ports that connect the switches together. Not sure what the problem is, but they are going live tomorrow and only have 48 out of 120 phones.
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
Trunk from 3500 going into SF300-8 #1 QNQTrunk from SF300-8 #1 going into trunk SF300-8 #2QNQ from SF300-08#2 going into Trunk SF300-24, All Vlans from Network 1 seem to be communicating properly between the 3550 and SF300-24 and is isolated from the Transport Network by QnQ. I am having one problem, I can not ping the SF300-24 or get to the management interface. I am able to access other devices on the SF300-24 Vlan1 from devices on the 3550 Vlan1 and vice versa.
View 1 Replies View RelatedAn end user is looking to connect 21x IP Cameras to the switch and they require at least 6W port port. Now, the datasheet states that each port on the SF300 provides 15.4W.I need to double check so that the end user will not start connecting the IP Cameras and then half of them might not fire up.
View 1 Replies View Relatedcisco 2811 - DHCP server..If IP Phone 3905 installed in SF 300 he does not receive an ip address. [code] If IP Phone 3905 installed in the Catalyst 2960 - all OK.
View 7 Replies View RelatedI'm playing with an SF300-24P switch and want to connect an IP Phone. I'm more familar with IOS syntax than the SF300 GUI.
How would I replicate the following in the SF300:
Switch(config)#int fa0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(Config-if)# switchport voice vlan 5
Not sure if setting the port to an ACCESS port on VLAN 15 (i.e. 15UP) and having the Voice VLAN set to 5 is correct.
Or should the port be set to General or Trunk with 15 as the untagged VLAN and 5 as the tagged voice VLAN (i.e. 15UP, 5T)?
My ISP is providing me with 1 public IP on a /30 network and 14 public IPs on a /28 network. In this example the 10.0.0.1 is the default gw provided by my ISP and 10.0.0.2 is my SF300-08. If I setup my router to route to 10.0.0.2 as the default gw through the interface between the switch and router, can I configure the static routes in the switch to route further to 10.0.0.1?
is it possible to have these 2 networks on different VLANs and configure inter-VLAN routing? I don't want the switch accessible from the 10.0.0.2 IP.
In my network I got 3 SF300 24 p switches. I managed vlan 10 for data and it is also a native vlan and vlan 20 for voice ,1st switch is the core switch and im having a problem in connecting them ?
View 7 Replies View RelatedAny chance of getting better ssh shell support on the SF300?Being able to do things like this are very useful:
ssh 10.1.1.1 "sh version"
ssh 10.1.1.1 "sh run"
my new Cisco SF300-48. I want to create 2 vlan (vlan 1 & vlan 2). The switch is set at layer 2. example : vlan 1 (port 1, 2, 3) , vlan 2 (port 4, 5, 6) vlan 1 can communicate each other (port 1, 2, 3) and vlan 2 can communicate each other (port 4, 5, 6)But vlan 1 cannot communicate with vlan 2.
View 4 Replies View Related