How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address)isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address) isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
I have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
View 3 Replies View RelatedI need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
How about supporting an scp server on the switch? Makes life much easier for collecting configs and pushing OS upgrades.
View 1 Replies View RelatedWe are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedI am looking for a how to configure a DHCP server for a Cisco SMB 300 series switch to obtain an automatic configuration. Currently i am using a Cisco 1800 router as my DHCP server and the DHCP pool serving the 300 series switch is configured as follows.
ip dhcp pool Cisco_SMB_300
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
[Code]......
Looking at pcaps, I don't even see a tftp request going the server after the switch obtains an IP via DHCP. The config file format is exactly as obtained from the download backup section (pretty sure its not the issue since i don't see a download attempt). Also, the SMB switch is running the latest firmware image (1.1.1.8)
Looking though the admin guide i did not see specifics on how the DHCP server was to be configure for the auto configuration feature to work.
I have sample lab dhcp-client ------- (vlan62) sg-300 switch (vlan62) ------ dhcp server
When I set on switch :
dhcp relay : enable
option 82 : enable
dhcp server address: ip of dhcp
When debug packets from client to server, there is no 82 option in dhcp discover packets. I mirror all traffic to mirror port with wireshark. I can see dhcp packets but without option 82.
Firmware version: 1.0.0.27
I have some issue from last 2 month on sf300.
The problem is that sf300 does not support complete dhcp, for that i put different internet modem.
I connected one internet modem in vlan 1 so users from that vlan can access internet and default gateway is nothing but Internet modem ip. user in the vlan are not communicate with other vlan because, other vlan users default gateway is Interface ip address. How i can give access to vlan 1 to access other vlan .
See the attached.
I have to used static route in all 3 devices or any one.
I saw a post in [URL] that was close to what I need to do. But this site seems a better place to ask a question. We need to install a second switch (SF300-24P) to an existing network with an SF300 48P and an ASA5500 for gateway/firewall etc. the network on the 48p switch is 192.168.1.xx. We want to use the new switch for ip cameras and 192.168.2.xx.
I will assume I need to set up a vlan on the 24 port switch for the 192.168.2.xx ip range, i will call this vlan20. I will guess that I need to pick a port from the 48p switch and create vlan20 on the 48p switch to access the 24p switch. I want users on the 192.168.1.xx network to be able to access cameras on the 192.168.2.xx network. Do I need to add a line in the asa config file for the new switch?
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
I am using a Cisco SRP527W router for our small business. As this device only has 4 LAN ports I want to add another switch so as our business grows I can add more PCs and VoIP phones. I would like to use a Cisco SF300-24 switch and before I purchase am interested to know if anyone has used a SRP527W router with this range of Cisco switches. Are there any compatibility issues or will these two devices work well together?
View 6 Replies View RelatedIs it possible to trunk a SF300 switch with a 3750 switch? If so how? Whenever I turn trunking on the 3750 port I lose connection to the SF300.
View 5 Replies View RelatedLooking through the logs of our SF300 switches I am seeing errors for SNTP:
%SNTP-D-NTPBADVER: NTP server version not compatible
We have two NTP servers listed, both are MS Windows 2008 R2 domain controllers. The actual time on the switches seems to be correct but we are still receiving these errors?
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies View Relatedi have a customer that will use this switch model.I was wondering if there is any recommendation from like an AS-BU for the most appropriate software version and what would be ?
View 4 Replies View RelatedI am going to purchase SF 300 24p POE Switch and if this Switch supports the configuration via console? As i have ESW-500 Series switches and it does not support console.
View 4 Replies View RelatedWe have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
Can we Configure DHCP server in 3750 ? we have configure DHCP server in 1841 router but some reason we want remove router .
View 2 Replies View RelatedI am using a fiber optic connection. I want to connect it directly to ASA5510. A WLC2504 will be connected to ASA and one Aironet AP will be deployed at first. (At this moment I am not using any Windows server but in near future I will need to deploy Windows Server 2003 in my corporate network) My questions are:
Can I configure ASA as DHCP server for my LAN?
Can I configure WLC as DHCP server for my LAN?
If we can configure both then what is the best practice from above two options? (I am new to Cisco stuff and first time user)
I want to set up a domain for a file server and MS SQL 2005 server on my server machine and installed windows server 2008 in it.
Do I need to set up DHCP server and DNS on Windows server 2008R2 or leave them to the router to do the job?
am having a switch 3860 it is configured dhcp , dns i want to change those dhcp , dns, what are the command that is use to reconfigure it
View 1 Replies View RelatedI have Cisco 3560X L3 switch and i need to configure DHCP on this switch. I have already configured below mentioned VLANs
VLAN 10 - 192.168.8.254 (USER VLAN)
VLAN 20 - 192.168.152.254 (REMOTE & VPN USERS VLAN)
VLAN 30 - 192.168.0.254 (SERVER VLAN)
After configuring DHCP, all the users needs to get IP from USER VLAN and all the servers should get IP from SERVER VLAN. If yes, what are the steps as I am very new in this kind of configuration.
Is it possible to configure an 881 router to act as a DHCP server to 4 VLAN's each with a different scopes all through a single ethernet interface?
View 2 Replies View RelatedWe've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies View Relatednow we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedI'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedI Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
Is there a way to configure a DHCP server for my internal subnet of 192.168.20.1 which is on a 3550 layer 3 switch from my 5505 ASA Firewall.My subnet of 10.1.1.0/30 is connecting my 5505 to 3550. All I'm trying to do is run a DHCP server down to my hosts. The only options on ASA 5505 is
dhcpd address 192.168.20.1 - 192.168.20.254 outside or inside, which conflicts with my subnet of 10.1.1.0 used to connect my internal subnet of 192.168.20.1 for the whole network.
When I used my router it did not need the (inside, outside) keywords and just an ip helper-address command. How do I configure my my firewall DHCP server to propagate the 192.168.20.0 network through my 10.1.1.0 connection.
know any plan from Cisco to make 300 series switch to work as a DHCP server?
View 1 Replies View Relatedwhen we use switch as dhcp server and we want to configure a DHCP relay on other subnet that is not connected to this switch, what is the DHCP server ip address for configuration of DHCP relay? Should we use vlan1 ip?
View 2 Replies View Related