Cisco Switches :: SF300-24P / Configure Vlan 10 For Data And Vlan 20 For Voice On The Same Port?
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
ADVERTISEMENT
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Feb 15, 2012
I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
View 1 Replies
View Related
Apr 14, 2011
I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies
View Related
Jun 4, 2013
If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies
View Related
May 16, 2013
im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
View 2 Replies
View Related
Oct 17, 2012
In my network I got 3 SF300 24 p switches. I managed vlan 10 for data and it is also a native vlan and vlan 20 for voice ,1st switch is the core switch and im having a problem in connecting them ?
View 7 Replies
View Related
Jan 2, 2013
my new Cisco SF300-48. I want to create 2 vlan (vlan 1 & vlan 2). The switch is set at layer 2. example : vlan 1 (port 1, 2, 3) , vlan 2 (port 4, 5, 6) vlan 1 can communicate each other (port 1, 2, 3) and vlan 2 can communicate each other (port 4, 5, 6)But vlan 1 cannot communicate with vlan 2.
View 4 Replies
View Related
Apr 22, 2011
I had made a DHCP server that had many scope:
1- scope: 192.168.1.208/28
2- scope: 192.168.1.224/28
3- scope: 192.168.16.0/24
[Code]....
How to condig SF300-24 to vlan 2 vlan 3 can get IP address from DHCP server in VLan 4?
View 14 Replies
View Related
Oct 6, 2011
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies
View Related
Jan 2, 2012
I have a SF300 24 P and Iam trying to configure a voice vlan this is what I have done so far and it doesnt work.
1. create vlan 30 for voice traffic and enable it
2. Telephony OUI add my mac address for allworx phones
3. Port to VLAN add 30 has tagged, port to vlan 1 untagged
4. Vlan to port I try to add 30 and get this error (Port e15 is candidate in voice Vlan 30 and cant be configured as static member in the vlan.
5. Under Discovery LLDP, LLDP MED port Setting Enable MED status, then all other options to yes
In my LLDP neighbor information all my phones are there and says under port ID 0 ( my phones support LLDP and CDP)
View 1 Replies
View Related
Oct 22, 2012
I have a Cisco SF300-24P deployed at a customer prem running only a couple VLAN's - 1 customer related and 1 for management. Recently the customer inquired about changing his connection to Q-in-Q. I have changed the interface type to customer but then it selects vlan 4095 as the vlan associated to that port. How do I change that vlan or by default is that the only vlan I can use? Currently the customer is using vlan 904 and would like to continue to use that vlan in the Q-in-Q config.
View 1 Replies
View Related
Dec 12, 2012
I bought a sf300 48 and made 4 vlans.
How can I restrict the mac address of device can be connect each vlan ? I just want allow the macs for vlan, dont need join the pc to a vlan.
View 8 Replies
View Related
Oct 12, 2011
I got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies
View Related
Sep 9, 2012
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies
View Related
Feb 12, 2012
I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traffic. I get no outbound audio on calls I can call out hear them fine they cant hear me. I am wondering if my tagged traffic leaving the phone is being striped and if so were. I have CDP turned off.
View 1 Replies
View Related
Apr 17, 2013
i have a asa5505 and sf300-48,in the sf300 have ip defult-gateway 192.168.1.93 and have internet in vlan2 but vlan 3 not work. ping from "vlan3" to "vlan2" its ok.
View 5 Replies
View Related
Sep 17, 2011
I'm planning to separate voice and data traffic with two vlans. I have a COR switch catalyst 3750, a UC560 for VOIP with SIP trunk and SGE2000P as access switches. The thing is i had configured VLAN1 (data vlan) and VLAN8 (voice vlan), i've created the vlan 8 in the database on 3750 and let pass those vlans through a TRUNK port. In the SGE2000P configuration i've created the VLAN8 and the the ports as trunk for letting pass the two vlans for the PC and the IP phone. This works but some phones aren't registering, and for example i've unplugged a register phone and plug and doesn't registering anymore.
View 0 Replies
View Related
Sep 13, 2011
We are about to install a new VoIP system (Allworx, which I did not select) and need to set up a new VLAN with QOS quickly for my SG 300 and SG 200 switches. I have the default VLAN1 at 10.0.0.0/24 and will be setting up VLAN10 at 10.1.0.0/24 for voice. There are a few other VLANS on the switches as well. I really don’t get the particulars of using a Voice VLAN vs. Smartport, but is one better than the other for this and what would be some good default settings to start with. I have command line and VLAN experience; I just haven’t set up a VLAN for voice from scratch.
View 1 Replies
View Related
Jul 25, 2012
I am having a problem with 6941 phones on a SG300.When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
View 1 Replies
View Related
Dec 10, 2012
I am having a problem with 6941 phones on a SG300.
When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.
I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.
CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.
If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.
The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
View 1 Replies
View Related
Oct 31, 2012
How can I configure Cisco 200 (SG200-08P) to learn Voice VLAN and CoS/DSCP from upstreamCatalyst 2960?
The Cat 2960 is today used together with LLDP-MED to announce config to Aastra IP Telephones. In some cases I need to use a small switch inbetween and plan to use the Cisco SG200-08P for this. However, I would like to avoid manual config of the Cisco 200 switch.
View 3 Replies
View Related
Nov 7, 2011
At our office we use seven Cisco 300 Series Small Business Switches. One main switch in the server room and one in each room. They work great! But I’m having difficulties getting the Auto Voice VLAN to work correctly. In fact, it seems to works straight away on a PoE model, but not on the non-PoE models.
Switch (main server room):
Cisco SG 300-28 (PID:SRW2024-K9)-VSD
Switches (one in each room):
Cisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10P (PID:SRW2008P-K9)-VSD
All these switches use firmware v1.1.1.8. The switches in each room are connected to the central switch by Link Aggregation. The main switch is configured in Layer 3 mode and all the others in Layer 2 mode. We have a lot of VLAN’s configured. For this problem allow me to describe only the two that are relevant.
VLAN 102 - Internal Network (Clients)VLAN 104 - Internal Network (Voice) The switches on each room are mainly used for clients, printers and IP phones. The clients and printers should operate in VLAN 102. The IP phones should operate in VLAN 104. For this to work I have the 10 port switches configured as following.
GE1 – Trunk – 102U;104TGE2 – Trunk – 102U;104TGE3 – Trunk – 102U;104TGE4 – Trunk – 102U;104TGE5 – Trunk – 102U;104TGE6 – Trunk – 102U;104TGE7 – Trunk – 102U;104TGE8 – Trunk – 102U;104TGE9 – Trunk – 1P (LAG 1, with 1U;102T;104T)GE10 – Trunk – 1P (LAG 1, with 1U;102T;104T)
The network is fully routable. A DHCP Server is available. Each VLAN uses DHCP relaying. If we statically assign a VLAN to a port, that just works fine. Auto Voice VLAN is enabled with VLAN ID 104. All switches are configured the same. But this is what occurs…
When I connect an IP phone on the SG300-10P the IP phones are assigned to the Voice VLAN ID 104. If I would connect a desktop to that same port it is assigned to VLAN ID 102. Exactly as it should.But when I connect an IP phone on a SG300-10 the IP it is assigned to VLAN ID 102. But I also noticed that in some cases they are assigned to VLAN ID 1 and don’t get an IP Address. That depends in which order I change settings. The port its VLAN membership is then even changed to 1P. Although the port is recognized as an “IP Phone” by the smartport feature. I have noticed it does make difference if I modify the smartport macro and change the native_vlan paramater from "1" to "let's" say "102". That seems to affect it. Of course it may be just coincidence. What am I doing wrong? How should it work?How should you actually configure each port on a switch? (trunk?, Tagged/Untagged VLAN?)If you do not use Telephony OUI. Do you still need to configure the macros on the smartport defenitions?
I have tried about everything. I have also tried Telephony OUI, but it doesn't make any difference. I just can't get it to work properly on the non-PoE switch.
View 6 Replies
View Related
May 20, 2010
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
View 11 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Aug 23, 2011
How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address)isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
View 1 Replies
View Related
Apr 20, 2011
I bought for a little office a SA520 Security appliance (for future VPN with another distant office) and a SG 300-10P switch for connect 3 PC and 3 IP PHONE. THe SA 520 is the router. I must configure 2 VLANs on the switch :
VLAN2 : DATA (for PC)
VLAN3 : VOICE (for IP PHONE)
VLAN1 : DEFAULT.
How can i simply configure all ports ? I would like to configure ports 1-4 on VLAN2 and ports 5-8 on VLAN3 and port G10 is reserved for the router SA520. I want to divise network DATA/VOICE.
I think i must create a trunk on G10 for SA520 ...
View 2 Replies
View Related
Feb 19, 2013
i purchased 300-28 how it config for stp and trunk
View 2 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Apr 6, 2013
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...
View 4 Replies
View Related
Apr 14, 2013
I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies
View Related
Mar 22, 2012
why i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies
View Related
