Cisco Switches :: SG-300 Haven’t Set Up A VLAN For Voice From Scratch
Sep 13, 2011
We are about to install a new VoIP system (Allworx, which I did not select) and need to set up a new VLAN with QOS quickly for my SG 300 and SG 200 switches. I have the default VLAN1 at 10.0.0.0/24 and will be setting up VLAN10 at 10.1.0.0/24 for voice. There are a few other VLANS on the switches as well. I really don’t get the particulars of using a Voice VLAN vs. Smartport, but is one better than the other for this and what would be some good default settings to start with. I have command line and VLAN experience; I just haven’t set up a VLAN for voice from scratch.
View 1 Replies
ADVERTISEMENT
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Sep 17, 2011
I'm planning to separate voice and data traffic with two vlans. I have a COR switch catalyst 3750, a UC560 for VOIP with SIP trunk and SGE2000P as access switches. The thing is i had configured VLAN1 (data vlan) and VLAN8 (voice vlan), i've created the vlan 8 in the database on 3750 and let pass those vlans through a TRUNK port. In the SGE2000P configuration i've created the VLAN8 and the the ports as trunk for letting pass the two vlans for the PC and the IP phone. This works but some phones aren't registering, and for example i've unplugged a register phone and plug and doesn't registering anymore.
View 0 Replies
View Related
Jul 25, 2012
I am having a problem with 6941 phones on a SG300.When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
View 1 Replies
View Related
Dec 10, 2012
I am having a problem with 6941 phones on a SG300.
When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.
I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.
CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.
If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.
The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
View 1 Replies
View Related
Oct 31, 2012
How can I configure Cisco 200 (SG200-08P) to learn Voice VLAN and CoS/DSCP from upstreamCatalyst 2960?
The Cat 2960 is today used together with LLDP-MED to announce config to Aastra IP Telephones. In some cases I need to use a small switch inbetween and plan to use the Cisco SG200-08P for this. However, I would like to avoid manual config of the Cisco 200 switch.
View 3 Replies
View Related
Nov 7, 2011
At our office we use seven Cisco 300 Series Small Business Switches. One main switch in the server room and one in each room. They work great! But I’m having difficulties getting the Auto Voice VLAN to work correctly. In fact, it seems to works straight away on a PoE model, but not on the non-PoE models.
Switch (main server room):
Cisco SG 300-28 (PID:SRW2024-K9)-VSD
Switches (one in each room):
Cisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10 (PID:SRW2008-K9)-VSDCisco SG 300-10P (PID:SRW2008P-K9)-VSD
All these switches use firmware v1.1.1.8. The switches in each room are connected to the central switch by Link Aggregation. The main switch is configured in Layer 3 mode and all the others in Layer 2 mode. We have a lot of VLAN’s configured. For this problem allow me to describe only the two that are relevant.
VLAN 102 - Internal Network (Clients)VLAN 104 - Internal Network (Voice) The switches on each room are mainly used for clients, printers and IP phones. The clients and printers should operate in VLAN 102. The IP phones should operate in VLAN 104. For this to work I have the 10 port switches configured as following.
GE1 – Trunk – 102U;104TGE2 – Trunk – 102U;104TGE3 – Trunk – 102U;104TGE4 – Trunk – 102U;104TGE5 – Trunk – 102U;104TGE6 – Trunk – 102U;104TGE7 – Trunk – 102U;104TGE8 – Trunk – 102U;104TGE9 – Trunk – 1P (LAG 1, with 1U;102T;104T)GE10 – Trunk – 1P (LAG 1, with 1U;102T;104T)
The network is fully routable. A DHCP Server is available. Each VLAN uses DHCP relaying. If we statically assign a VLAN to a port, that just works fine. Auto Voice VLAN is enabled with VLAN ID 104. All switches are configured the same. But this is what occurs…
When I connect an IP phone on the SG300-10P the IP phones are assigned to the Voice VLAN ID 104. If I would connect a desktop to that same port it is assigned to VLAN ID 102. Exactly as it should.But when I connect an IP phone on a SG300-10 the IP it is assigned to VLAN ID 102. But I also noticed that in some cases they are assigned to VLAN ID 1 and don’t get an IP Address. That depends in which order I change settings. The port its VLAN membership is then even changed to 1P. Although the port is recognized as an “IP Phone” by the smartport feature. I have noticed it does make difference if I modify the smartport macro and change the native_vlan paramater from "1" to "let's" say "102". That seems to affect it. Of course it may be just coincidence. What am I doing wrong? How should it work?How should you actually configure each port on a switch? (trunk?, Tagged/Untagged VLAN?)If you do not use Telephony OUI. Do you still need to configure the macros on the smartport defenitions?
I have tried about everything. I have also tried Telephony OUI, but it doesn't make any difference. I just can't get it to work properly on the non-PoE switch.
View 6 Replies
View Related
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Sep 13, 2011
Why aren't the fa ports that i assign to a voice vlan showing up when i issue show vlan?
View 2 Replies
View Related
Apr 14, 2011
I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies
View Related
Dec 15, 2011
Critical voice vlan feature, used to place a newly authenticating phone when radius server is dead into appropriate voice vlan, seems to be a new feature and I find the documentation to be incomplete. Do the following switches support this feature in any IoS versions? WS-C4510R, 4506, 3560, 3550,2960s.
View 1 Replies
View Related
Dec 4, 2011
I'm using CISCO 3524 switch as access switch and trying to enable voice vlan in fast eth ports as below.
L3 vlans are created in core switches which is cisco 6509
vlan 1 - data vlan
vlan 2 - voice vlan
in cisco 3524
[code]....
if i use the above configs, the phone which is connected to interface fa0/1 is not taking ip from dhcp server. even it didn't work with static configs.while troubelshooting, i have configured as below and it's started working..
int fa0/1
switchport acces vlan 2
speed 100
duplex full.
in this case i can't use this port for data connectivity where as it's required for data too.
View 2 Replies
View Related
Apr 9, 2012
I have CME on Router 2800 series, and switch 2960 PoE connected to this router.On 2960 switch, there is existing 7945 IP Phone that already work properly and get IP 14.x.x.x from voice vlan 2.
Problem is when I add cisco 6921 IP Phone connect to 2960 switch, it get data vlan 10.x.x.x, not voice Vlan 14.x.x.x I have check CDP and it use CDP v2
Config on 2960:
interface GigabitEthernet1/0/34 <--- this is connected to IP Phone 7945
switchport mode access
switchport voice vlan 2
spanning-tree portfast
[code]....
With same config and condition on port 2960, why the IP Phone 6921 can't get voice vlan 14.x.x.x, whereas IP Phone 7945 can get voice vlan 14.x.x.x
View 2 Replies
View Related
Nov 10, 2012
I have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
View 7 Replies
View Related
Jun 4, 2013
If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies
View Related
Nov 9, 2011
i am facing a strange issue on cisco 2950 .IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1) suddenly my phone stopped working for DTMF tone, i mean when i dial a conference bridge lets say 6565 and then it ask for conference bridge code lets say 12345, it doesnt recognize the code and says code is invalid, SIP Proxy is Asterisk in this case.Currently my cisco switch port is configured for dual data + voice vlan, where DTMF dont work, sample config below [code]
View 2 Replies
View Related
May 16, 2013
im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
View 2 Replies
View Related
May 20, 2010
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
View 11 Replies
View Related
Mar 19, 2013
The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies
View Related
May 14, 2012
I am trying to write an extended ACL for the voice vlan.My scenario is the following:I have two PBXs with two Catalyst 4505 L3 switches.The C4505 are connected trough a trunk link.I have a VTP domain configured.
Voice VLANs are Vlan 100 and Vlan 101 with networks 10.2.0.0/16 and 10.4.0.0/16 Voip telephones are communicating between them self and everything is working fine.I want to secure both voice VLANs with an ACL to allow only couple of IPs to administer the phones.The PCs are connected trough a integrated switch via VOIP telephone.Here is the sample configuration of the dhcp pool for the PC VLAN:
ip dhcp pool PCs
network 10.1.0.0 255.255.0.0
default-router 10.1.1.1
dns-server 10.10.10.1
option 43 hex 010a.5369.656d.656e.7300.0000.0204.0000.0064.0000.0000.00ff
I had to implement the 43 hex option because the PCs did not get the ip from the DHCP because of the vendor specific information.The thing that worries me is will the DHCP forward the ACKs for the PCs if I implement this test ACL:
ip access-list extended VLAN100
permit ip 10.2.0.0 0.0.255.255 10.4.0.0 0.0.255.255
permit ip 10.4.0.0 0.0.255.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.4.0.0 0.0.255.255
permit udp host 0.0.0.0 eq bootpc host 255.255.255.255 eq bootps (this I am not sure do I need)
permit udp host 255.255.255.255 eq bootps host 0.0.0.0 eq bootpc (also this)
deny ip any any
I only want to allow the network 192.168.2.0/24 and maybe some other hosts to access the web based http gui to adiminister the IP phones.All PCs are connected trough the VOIP terminals. I do not want to deny the traffic to PCs.
View 8 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
View Related
Feb 12, 2013
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
View 1 Replies
View Related
Sep 17, 2012
I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
View 5 Replies
View Related
Apr 12, 2012
I'm struggling with a configuration issue on the Cisco SG200-08P. We are using the Cisco SG200-08P on a mobile cart that will go from class room to class room that will have computer and cisco Voip phone plugged into it. The issue is that each of our closets are in differnt VLANS ( 1 voice and 1 data....lets say data vlan 20 and voice vlan 2025 for conversation) and that we route to each closet.It would be great if I could just create a generic data and voice vlan to dynamically pick up what the upstream switch has however, it seems that I've been unsuccessful in doing so. I can pass the data Vlan no probablem. The upstream switch port is set to access port and a switch port access voice vlan (these are 3750x switches) If the above is not possible I guess I will take what I can get. Should I just create data vlan 20 and voice vlan2025 on the Cisco SG200-08P and make a trunk port on the Cisco SG200-08P and a trunk on the 3750x? Is there an option on the Cisco SG200-08P to tag voice traffic?I'm also concerned with VTP and I did not see an area in the Cisco SG200-08P to set that as a client and transparent mode.
View 6 Replies
View Related
May 16, 2011
how many concurrent voice call can be conducted at once with the cisco sf 100d-08 8-port 10100 switch?
View 1 Replies
View Related
Apr 8, 2013
I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
View 4 Replies
View Related
Sep 11, 2012
recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
View 3 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Apr 6, 2013
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...
View 4 Replies
View Related
Oct 6, 2011
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Feb 25, 2013
I'm trying to configure the 1130AG from scratch but I'm not having any luck. I tried using the IPSU utility and entered the MAC address but it errors, "The device does not answer". I have connected it to a network so it can get an IP from DHCP but it doesn't respond. And when it boots up from factory reset there is no SSID broadcast for me to connect to. I have tried connecting through the Ethernet port and the Console port to my computer but no luck.
View 3 Replies
View Related
