Cisco Switching/Routing :: 2960 POE Switch Voice Vlan Configuration To Work With Non IP Phones?
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
ADVERTISEMENT
Jul 5, 2012
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
View 2 Replies
View Related
Dec 4, 2011
I'm using CISCO 3524 switch as access switch and trying to enable voice vlan in fast eth ports as below.
L3 vlans are created in core switches which is cisco 6509
vlan 1 - data vlan
vlan 2 - voice vlan
in cisco 3524
[code]....
if i use the above configs, the phone which is connected to interface fa0/1 is not taking ip from dhcp server. even it didn't work with static configs.while troubelshooting, i have configured as below and it's started working..
int fa0/1
switchport acces vlan 2
speed 100
duplex full.
in this case i can't use this port for data connectivity where as it's required for data too.
View 2 Replies
View Related
Jun 4, 2013
If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies
View Related
Sep 11, 2012
recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
View 3 Replies
View Related
Sep 17, 2012
I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
View 5 Replies
View Related
Mar 11, 2013
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies
View Related
Jan 28, 2013
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
View 3 Replies
View Related
May 19, 2013
I am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies
View Related
May 5, 2013
I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies
View Related
Oct 21, 2011
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
View 1 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Apr 17, 2012
We have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies
View Related
Mar 21, 2013
I have a Catalyst 2960-S switch and a pre-standard IP Phone (Cisco 7960). When I connect the phone to the switch the switch recognizes the phone and supplies power. I would like to prevent this behaviour. ie. I would like to disable detection of pre-standard equipment. Is there a command I can issue on the 2960-S to do this? For example, on a switch from a different vendor I can issue the command: no power pre-std-detect to prevent it from detecting the 7960 phone, is there an equivalent command on the Catalyst 2960-S ?
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
Oct 31, 2012
How can I configure Cisco 200 (SG200-08P) to learn Voice VLAN and CoS/DSCP from upstreamCatalyst 2960?
The Cat 2960 is today used together with LLDP-MED to announce config to Aastra IP Telephones. In some cases I need to use a small switch inbetween and plan to use the Cisco SG200-08P for this. However, I would like to avoid manual config of the Cisco 200 switch.
View 3 Replies
View Related
Feb 20, 2013
i have new project in hospital with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work first the 2 core switch for redundancy then each catalyst switch 2960 connected to the core with 2 uplink each uplink for each core switch that way i have rendundancy in the connection then i need one vlan ?i need to configure this switch to work perfectly with each other in best redundancy mode?
View 2 Replies
View Related
Apr 9, 2013
I have a Cisco 6500 which has two VLANs defined
VLAN 30 for Data VLAN
VLAN 31 for Voice VLAN
I have two Cisco 3750 switches.both switches are connected to IP Phones.the configuration of Cisco 6500 Trunk Port to Cisco 3750 is [code] On Cisco 3750, the trunk port to 6500 has the configuration [code].The IP Phones connected to the Cisco 3750 are 7911,7979, 7940, 7961.
All phone are working fine, the phones get their ip address from voice vlan, and systems connected to phones get from data vlan, except 7940/7960.
These two models of IP Phones remain on Configuring IP, and when you check the IP Settings, it gives Data VLAN IP, which does not have a TFTP.once you manually enter TFTP address in the field, it registers instantly, due to ip routing in the network.
these phones were working fine before, but suddenly few days back they went out of the network, and still are in Configuring IP state.I also tried to convert these ports connected to 7940/7960 to access ports [code] but still the IP is taken from the Access Vlan (30). Even If you configure a single VLAN on these ports, the IP phones then never get the IP.
View 6 Replies
View Related
Apr 9, 2012
I have CME on Router 2800 series, and switch 2960 PoE connected to this router.On 2960 switch, there is existing 7945 IP Phone that already work properly and get IP 14.x.x.x from voice vlan 2.
Problem is when I add cisco 6921 IP Phone connect to 2960 switch, it get data vlan 10.x.x.x, not voice Vlan 14.x.x.x I have check CDP and it use CDP v2
Config on 2960:
interface GigabitEthernet1/0/34 <--- this is connected to IP Phone 7945
switchport mode access
switchport voice vlan 2
spanning-tree portfast
[code]....
With same config and condition on port 2960, why the IP Phone 6921 can't get voice vlan 14.x.x.x, whereas IP Phone 7945 can get voice vlan 14.x.x.x
View 2 Replies
View Related
Nov 10, 2012
I have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
View 7 Replies
View Related
May 15, 2012
I would like to know if there an specific configuration in order to apply QoS configuration in Switches 3750X for Polycoms Phones.I was reviewing the information from Cisco but mostly of them apply only for cisco phones, and just some or basic for non cisco phones.
View 1 Replies
View Related
Nov 9, 2011
i am facing a strange issue on cisco 2950 .IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA9, RELEASE SOFTWARE (fc1) suddenly my phone stopped working for DTMF tone, i mean when i dial a conference bridge lets say 6565 and then it ask for conference bridge code lets say 12345, it doesnt recognize the code and says code is invalid, SIP Proxy is Asterisk in this case.Currently my cisco switch port is configured for dual data + voice vlan, where DTMF dont work, sample config below [code]
View 2 Replies
View Related
May 16, 2013
im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
View 2 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
May 20, 2010
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
View 11 Replies
View Related
May 14, 2012
I am trying to write an extended ACL for the voice vlan.My scenario is the following:I have two PBXs with two Catalyst 4505 L3 switches.The C4505 are connected trough a trunk link.I have a VTP domain configured.
Voice VLANs are Vlan 100 and Vlan 101 with networks 10.2.0.0/16 and 10.4.0.0/16 Voip telephones are communicating between them self and everything is working fine.I want to secure both voice VLANs with an ACL to allow only couple of IPs to administer the phones.The PCs are connected trough a integrated switch via VOIP telephone.Here is the sample configuration of the dhcp pool for the PC VLAN:
ip dhcp pool PCs
network 10.1.0.0 255.255.0.0
default-router 10.1.1.1
dns-server 10.10.10.1
option 43 hex 010a.5369.656d.656e.7300.0000.0204.0000.0064.0000.0000.00ff
I had to implement the 43 hex option because the PCs did not get the ip from the DHCP because of the vendor specific information.The thing that worries me is will the DHCP forward the ACKs for the PCs if I implement this test ACL:
ip access-list extended VLAN100
permit ip 10.2.0.0 0.0.255.255 10.4.0.0 0.0.255.255
permit ip 10.4.0.0 0.0.255.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.4.0.0 0.0.255.255
permit udp host 0.0.0.0 eq bootpc host 255.255.255.255 eq bootps (this I am not sure do I need)
permit udp host 255.255.255.255 eq bootps host 0.0.0.0 eq bootpc (also this)
deny ip any any
I only want to allow the network 192.168.2.0/24 and maybe some other hosts to access the web based http gui to adiminister the IP phones.All PCs are connected trough the VOIP terminals. I do not want to deny the traffic to PCs.
View 8 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Feb 12, 2013
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
View 1 Replies
View Related
Aug 27, 2012
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies
View Related
Oct 23, 2012
I'm having some trouble with a 4510 Switch Line Card. I need some recomendations for troubleshooting it.We have some PoE phones connected to the card number 3. When those phones were restarted, they did not go up again. In order to discard wiring issues, we connected the phone directly to the card 3, and the phone did not go up. If the phone is connected to a different card, it goes up correctly.
Additionally, to restore the service, these phones were migrated to other cards, but when we disconnect the equipment, ports in line card 3 remain in an up / up state (and nothing is connected to those ports!!), and only reflect the actual state after restarting the port.What steps could I do in order to troubleshoot this issue?. What should I look for, or how do I discriminate the problem? Might it be a hardware issue, a PoE issue?
View 3 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
