Cisco Switching/Routing :: WS-C2960-24TC-S / Switch Configuration To Work Perfectly In Redundancy Mode
Feb 20, 2013
i have new project in hospital with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work first the 2 core switch for redundancy then each catalyst switch 2960 connected to the core with 2 uplink each uplink for each core switch that way i have rendundancy in the connection then i need one vlan ?i need to configure this switch to work perfectly with each other in best redundancy mode?
View 2 Replies
ADVERTISEMENT
Apr 26, 2012
I have two WS-C2960-24TC-L Switch with Software Ver 12.2(25r)SEE6 with image c2960-lanbase-mz.122-35.SE5.bin and 12.2(25r)SEE1 with image c2960-lanbase-mz.122-25.SEE2.bin currently on it.
I want to enable SSH connections on the switches and believe I need to import the cryto image onto the switch. I would like to upgrade it to new version that can also support ssh connection but not sure which image to download from cisco. The switches are now live.
System image file is "flash:c2960-lanbase-mz.122-35.SE5/c2960-lanbase-mz.122-35.SE5.bin"
cisco WS-C2960-24TC-L (PowerPC405) processor (revision H0) with 61440K/4088K
[Code].....
View 5 Replies
View Related
May 19, 2013
I have an issue with one of our switches, switch model WS-C2960-24TC-L, i am not able to display switch temperature as below,
Switch#sh verCisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)Technical Support: URL ) 1986-2013 by Cisco Systems, Inc.Compiled Tue 05-Feb-13 12:41 by prod_rel_team(code)
View 2 Replies
View Related
Sep 15, 2008
I'm trying to configure the GigabitEthernet interface of the WS-C2960 switch to have a full duplex. Unfortunately, there is no option to configure this neither is the speed of that interface. But these options are present in FastEthernet ports. Is there a bug in SW version 12.2(35)SE5 that explains this abnormality?
View 6 Replies
View Related
Jul 18, 2012
A quick one because I'm scratching my head trying to figure the difference between the 2960 LAN Base and LAN Lite IOS installs. I want to put a 2960 into a site which has as layer 2 link on dark fiber taking it elsewhere. This part I'm not concerned about - the WS-C2960--24TC will do what I need without issue - but I don't know if I can get away with LAN Lite, or if I need LAN Base.
I basically need V LAN's with associated SVI's, and a routed link on the up link port (I don't care if it's a switch port with an associated SVI or a no switch port and IP address), but it's got to be able to run OSPF. Can I do this with LAN base on this series switch? Or do I need to go for a higher series (3560?). I *could* get away with static routes, but my boss is walking death on them unless I can 100% prove they're necessary, so I'd rather not right that fight!
View 5 Replies
View Related
Sep 19, 2012
I'm having problems with a cisco switch WS-C2960-24TC-L version 12.2 (50) SE5. every night the equipment goes down, and every morning around 8am comes up.
I know it comes up at 8am because at that time I arrive at my workplace and see the alarm that the switch did not backup the config. ip using his web page and see what's up for a few minutes.
but I never could discover what time vai below. is there any way to see?? with the command show logging don't appear the hoursthat came down...he was only following the hours that he came up ...
View 4 Replies
View Related
Sep 10, 2012
My 2960-24TC-L switch is startet up and shows up: switch.Have tried to upload new image with xmodem without success.There must be a procedure to upload the new image, I have looking for hours and can not find the procedure.
View 3 Replies
View Related
Mar 5, 2013
I am trying to configure a 3500XL switch (and I know its old). I get to the int fa 0/1 line and thats where it all stops working.
switch#(config-if)#switch port mode access
switch#copy run start
or
switch#(config-if)#switch port mode access
switch#sh run int fa 0/1
It will show the configuration for port fa 0/1 as if I hadn't entered the "switch port mode access" command. Or any other command for that matter. Why the switch is not holding configuration and seemingly loses it as soon as you exit out of each interface?
View 4 Replies
View Related
Aug 7, 2012
I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies
View Related
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
View Related
Oct 31, 2012
Why rpr is the only available redundancy mode option available to me. I'm running a 4507R+E with twin SUP7-E's.
Abbreviated show ver Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.03.01.SG RELEASE SOFTWARE (fc2)Technical Support: [URL]/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Sun 26-Aug-12 13:45 by prod_rel_team
ROM: 15.0(1r)SG2gp08401 uptime is 6 weeks, 6 days, 4 hours, 59 minutesUptime for this control processor is 6 weeks, 3 days, 2 hours, 21 minutesSystem returned to ROM by RPR SwitchoverSystem image file is "bootflash:/cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1.bin"Jawa Revision 7, Snowtrooper Revision 0x0.0x1C
[code]....
View 3 Replies
View Related
Nov 15, 2011
I'm not able to find power redundancy mode when i do show power on my Cisco 4510R+R with SUP7E.
[code]...
When i do show power on my Cisco 65000 the first line shows the power redundancy mode, I have all other show power related command but couldn't find redundancy mode
View 1 Replies
View Related
Apr 4, 2013
Customer has a Catalyst WS-C2960-48PST-L. and in some ports we have VoIP phones with PoE company Aastra. If I use first config we have problem when phone boot up.
First config:
description tp-11-voip
switchport access vlan 250
switchport mode access
switchport voice vlan 201
switchport port-security maximum 2
switchport port-security(code )
The MAC shown here is from a voip Phone. After the phone boot up, the p, because it must boot first in vlan 250 (access vlan). On the port you can only see the MAC from vlan 201. With the second config the phone can boot without problems:
interface FastEthernet0/48
description tp-11-voip
switchport access vlan 250
switchport mode access
switchport voice vlan 201
is there a reason, why it is the problem with the first config on cat2960 ? The same first config works with an Cat2950 without problems.
View 3 Replies
View Related
Feb 27, 2012
On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
View 9 Replies
View Related
Apr 23, 2013
I have a C2960-24TT-L Switch with the following problem:When the Power Cord is plugged in the Switch, all switch indicator LEDs go on very briefly. Then SYST LED blinks very briefly, goes on steady and remains at this state without any indication at the console.Tried the reset by holding the MODE button while plugging in power but I still get no indication at the console. All is fine with console, meaning that if I take out the cable and plug it in another switch, then I see all that there is there to be seen.My question: Is the switch beyond repair or is there something that can be done to get the switch to run POST and boot at rommon so that I can reload SW and configs?
View 3 Replies
View Related
Feb 7, 2012
I've got a C2960 (sw01) and a C2948. (sw02) The sw02 switch is trunked with sw01, and is meant to serve as an extension to the VLANs (1-4) that exist on sw01. It is trunking properly, however, how would I go about giving the sw02 an IP so that I can access it via SSH? Would I have to create a VLAN specifically on sw02 with an ip and switchport an interface to use it? I know that a VLAN can only have a single IP, but I'd like sw02 to have an IP on VLAN1 (192.168.1.0 subnet), is that possible?
View 5 Replies
View Related
Feb 14, 2012
i am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error:Failed to execute the command archive download -sw /overwrite /http iosFile
View 2 Replies
View Related
Feb 20, 2013
Is it possible to configure both Catalyst WS-C2960-24PC-L and Switch Cisco SG300-28 to work together for VLANs for voice and data ? If yes, can you give me the resources which I can refer to ?
View 4 Replies
View Related
May 12, 2013
It looks like pretty basic config, but it does not work. I have 1x 2602i autonomous mode AP, 1x C2960 switch (with inter-vlan routing prefered SDM template) and 1x 1841 router.
I trunk between Switch and Router works smoothly, but it does not work between AP and Switch or AP and Router.
Configuration looks like this:
AP2602i:
interface GigabitEthernet0
no ip address
duplex full
speed 100
[code]....
View 12 Replies
View Related
Nov 8, 2011
I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies
View Related
Dec 15, 2012
does the WS-C2960-24TT-L switch support power over Ethernet ?
View 2 Replies
View Related
Jun 24, 2009
in a customer project we are evaluating if it's possible to connect from cisco ios switches via "ssh -l <user> <ip address>" to an enterasys n series dfe modul which is running a ssh server v2.
Unfortunately this doesn't work as expected, every connection attempt is resetted.We did a trace of the ssh connection attempt where you can see that there is some problem in the algorithm negotiation (see attachment).
Equipment/OS:
- Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(44)SE1
- Enterasys 7H4382-49, Fw: 05.42.10
View 3 Replies
View Related
Feb 26, 2013
I have a 3com 2948 switch and is needing to put the configuration on a Cisco WS C2960 48 port switch. I am attaching the config to heck if that is correct. I know my IP will need to change to .123
View 7 Replies
View Related
Oct 31, 2012
My network consist of that network device. cisco catalyst 3750 with stackwise, 2xnexsus 5000 series and servers.servers connected to nexsus switch. nexsus connect to 3750.
Each server have two link, one of them connect nexsus1 and other connect to nexsus2 switch.(same traffic) each nexsus have one link to 3750. At 3750 the nexsus link configurate etherchannel. but the flapping occur at 3750.
i understand that at 2 nexsus link have the same server source mac address so the flapping occur at 3750. how i solve this problem?
View 5 Replies
View Related
Sep 16, 2012
I have the following: 1 5520 ASA connected to the internet, 2 core switches, and several access switches.Aside from implementing RSTP, VRRP, hard code access and trunk ports, is there any other recommendation you would like to add.
View 7 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 8, 2012
I want to know what is the different between IOS of the catalyst WS-C2960-48PST-S and the IOS of catalyset WS-C2960-48PST-L.a want to upgrad the IOS of a WS-C2960-48PST-S with the IOS of WS-C2960-48PST-L (because this reference has a LANBASE version of IOS).
View 4 Replies
View Related
Oct 1, 2012
I have a switch 2960-24TC-L with GEC (realised with 2 giga interface uplink) with switch 3750. the configuration is ok, the GEC is up and other feature working. I try to upgrade 2960-24TC-L from 12.2.44SE6 to 12.2.46 or 12.2.5x or 15.0.x...the upgrade it's ok the swithc boot..and the configuraiton is same.. but the giga 0/1 and 0/2 on 2960 not bring up....and the better the interface on 3750 are up.
View 3 Replies
View Related
Jul 24, 2012
My Cisco Catalyst 2960G-24TC-L is broken.Yes,I think it's broken.
1.Always dispaly : “ !!! WARNING: The switch is not usable !!! ” “Unable to create l2trace server process, socket_open() failed”.
2.All GigabitEthernet is missing .
Switch(config)#interface ?
Async Async interface
Auto-Template Auto-Template interface
[Code].....
View 5 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Dec 20, 2012
Recently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies
View Related
Feb 8, 2012
We've just purchased a WS-C3750-24FS-S, only to find that the 100baseFX ports will not work over Single Mode fibre, backhaul links. Any way or a device that convert from MM to SM?
View 2 Replies
View Related
Apr 22, 2013
my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
View 6 Replies
View Related