We've just purchased a WS-C3750-24FS-S, only to find that the 100baseFX ports will not work over Single Mode fibre, backhaul links. Any way or a device that convert from MM to SM?
View 2 RepliesI have a new building to add to our campus and I have been encouraged to run single mode fiber. All of my other buildings are connected with multi-mode fiber. I just want to make sure i will not have an issue if I run single mode to the new building with SM SFP's.
View 2 Replies View RelatedWe have WS-C3750-24FS switches stacked supporting users on our LAN. I want take advantage of the netflow capabilities of the WS-C3750X using the C3KX-SM-10G card.
Would I be to see netflow data coming from the WS-C3750's if I stacked it with the WS-C3750X?
Also I read that the C3KX-SM-10G card would support a 1G SFP is that correct?
we are having trouble with the VPC, and etherchannel ? looked at many forums not to clear on wich one to use, this is are config, we have been getting alot of loops and kills are entire network
nexus switch config, this is on both nexus we have 2 of them at this site, that talk back to 2 other ones back to another site
pd554801
interface port-channel9
description *PD3750_Fiber01 network rack*
[Code].....
Using SFP-10G-LRM with single mode fiber? We have 1310nm.
View 2 Replies View RelatedI'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies View RelatedThe module WS-X4306, support fibber fiber single mode ó fiber multi mode? what GBIC is for fiber single mode or fiber multi mode?
View 1 Replies View Related I'm having a problem with some new gear and can't seem to figure it out. I have a 3750X-48P-S with a C3KX-10G-NM using SFP-10G-LR transceivers and I'm trying to trunk that with a 6509 that has a X2-10G-LR transceiver over single mode fiber. This is not working. Cisco TAC says the SFP+'s that we just got brand new are both bad and we need to order new ones. I find that hard to believe but who knows.
The switch recognized the module and I tested all 4 ports in gigabit mode using GLC-SX-MM transceivers, all worked great. I have the SFP+'s in tengig1/1/1 and 1/1/2 as they should be. There are no other SFP's in the module either.
When I do a sho int tengig1/1/1 and 1/1/2 the media type doesn't show the transceiver that is installed like it does for the GLC-SX-MM ones. Maybe it's not supposed to or maybe it just doesn't recognize them and it's a hardware issue.
connecting a Cisco 3945 Router to an Ethernet WAN Link. The service provider has provided a 100M Ethernet Single Mode Fiber handoff to the customer premises with SC Connector. The CPE configuration proposed for this setup is like this. [code]
Since the SFP has LC Connector, i suppose i need to have an SC-LC Cable for connecting the Ethernet link. Do i need anything else, apart from above?
Prior we only had 62.5u multi mode.I've got 3750x switches and new SM SFP and yellow fiber patch cables. None of my links show connected. No lights and trunk port interfaces show down/down.
Is there a special command you have to do on a port when using SM fiber? Do you think I need cross over fibers?
Also, should I be able to see a laser signal light like MM or is SM a different frequency so it's not as visible as MM?
We have Fiber link down down from both ends. From switch A goes to fiber box then to other fiber box then to switch B.
Switch A
Model: WS-X4418-GB-Gbic
Type: 1000BaseSX
Switch B
Model: WS-C3750G-24TS-1U
Type: 1000BaseSX SFP
Both sides are configured as trunk .
I have 3 Data centres which I am linking up via Single Mode Single Strand Fibre.The switches at each data centre are WS-C4948-E
-Distance between Data Centre 1 and Data Centre 2 is 60km single mode single strand
-Distance between Data Centre 2 and Data Centre 3 is 70km single mode single strand
What type of SFP do I need to use in each Data Centre for the WS-C4948-E switches for these distances.
I'm working with a customer who has an SGE2000P and a Catalyst 2960 to setup and configure a single mode fiber link. The SGE2000P has an MFELX1 fiber GBIC and the 2960 has a GLC-LH-SMD GBIC. When I have the customer plug in his fiber, there is a power light that comes on on the MFELX1 GBIC. Neither GBICs/switches show that a link or activity is occurring, but the presence of that light makes me think that they are connecting somehow. Are these two switches/GBICs compatible?
View 1 Replies View RelatedI have a 7206vxr with a NPE-G1 card in it. I am planning to add some PA-GE card with a ws-g5486 to light single mode Gigabit dark fibre.
it seems that users are experiencing throughput of around 200Mbps. Is this per card, or for the entire chasis? I have 6 free slots, if i were to fill 3 of them up with PA-GE card would i get 200Mbps on each card ?
I have stacked WS-C3750E-24PD with Ten Gigabit Ethernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it. One of the Ten Gigabit Ethernet ports, goes to err-disable mode with following errors on that specific ports.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm. (DROmx-1-1)
I have gone through some of CSC forums like {URL}. The workaround is to "Remove the X2 or SFP from the inactive up link port" which is not in my case.
I have a requirement to connect two 3750 switch with 10G speed between two sites with 150km distance. We will lay-out our own fiber (48 core) between two sites. I just want to consult the following:
1. Could i use two core switch 6500 with single mode fiber as a transport equipment?
2. Or i need to use SDH equipment because of the distance concern? If so do i need a repeater?Could i use Cisco Metro Core ONS, which one?
3. Any other option to achieve this requirement?
Can I use the SFP-10G-SR 10g interface woth Multi - Mode fiber?
View 3 Replies View RelatedAfter powering up a WS-C3750-48PS switch, Normal POST LED flashing of lights does not happen, instead the switch is stuck in SYST Mode on the front panel. My attempt to hold down the mode button upon powering up for 15 sec fails to reboot the switch. I cannot console to the switch. Is this switch unrecoverable? Should I RMA with TAC?
View 5 Replies View RelatedI have an old Cisco 3500XL I am using for my home lab, but was wondering can I use the fiber ports to connect to my PC. I have to correct NIC interfaces but no link indication. I did make sure the port was no down, but sill not link.
View 8 Replies View RelatedWe have a scenario where we want to connect 14 access layer 2950 switches to Core switch 3750 via optical fiber in a LAN.What model of 3750 Switch should we use to tackle this situation.I have learnt that WS-C3750X-24P should support it.Isnt it?
Can we use optical fiber SFP module to connect 2950 switches to core switch?Does Cisco 2950 Switch support optical fiber sfp module?
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies View RelatedI am doing an small project, I have to connect 4 cisco switches SF 302-08 (1 GBIC each one) to a core switch SGE 2000 (4 GBICs). Because of cable length I have go connect all 5 switches with fiber. The fiber termination is multimode LC duplex. My confusion is on the mini GBICs. There is compatibilities issues i been reading. [code]
View 3 Replies View RelatedWe have a project in which we are using 34 Cisco SG200-18's each with a MGBLX1 (LC Single Mode Fiber) SFP mini-GBIC.All the fiber's come back to one building where we must "bridge" all 34 fiber connections. What hardware should be used to accomplish this? A L2 switch? For example, a 12 port SFP Switch with Fiber SFP's accepting the first 12 fiber connections, then other switch with SFP for the next 12 and so on, until there is a overall capacity of 36 and having patch cables between the 3 switches?
what cisco or non cisco hardware would work with these SF200-18's to accomplish this?
I am troubleshooting a fiber connectivity issue.Now I have two switches, one is 3750, and another is small biz 300 series switch. Both switch has a single mode smf gbic. Now I have two swtiches face to face and connect with a single mode cable. Do you think if I would get a link light on? Both ports are no shutdown.
View 3 Replies View RelatedI am struggling to find an SFP transceiver, single mode, that operates at 100Mbps in a 1000Mbps port in an ME3600 or ME3800.
View 5 Replies View RelatedDoes Nexus 7K support Multiple VDCs sharing ports on a single line card. One of our cisco parnter engineers stated that cisco doenst recommend using same line card for multiple VDCs.The second VDC (Non-Default VDC) will be used four our Outside, and DMZ Segment, and to phyiscally segregate our Firewall from our Internal/Inside Core Switch without using a physical DMZ Switch.I know Cisco used the Nexus in this way in their PCI DSS 2.0 Compliance Document. Module is N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 10/100/1000 Mbps Ethernet XL Mod N7K-M148GT-11L
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
I've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View RelatedI am having 2950 Cisco switch. After completing the boot process LAN Ports are working for few minutes afterwards Ports are going into Orange Signal Mode.
View 1 Replies View Relatedi have new project in hospital with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work first the 2 core switch for redundancy then each catalyst switch 2960 connected to the core with 2 uplink each uplink for each core switch that way i have rendundancy in the connection then i need one vlan ?i need to configure this switch to work perfectly with each other in best redundancy mode?
I got an ASA 5510 system currently in single context mode, with CSC SSM installed. Single ISP uplink to internet, no VPN. And now customer would like add another ISP uplink, without invest another box for HA.What come across my mind is make the current box into multi context. There's some area i need to concern and also need yours perspective on it.
Question 1: For making the firewall into multi context, am i need to do it from scratch, issue mode multiple command. Then rebuilt the current production config into one of the context, then another context meant for the new IPS uplink, and one admin context?
Question 2: For CSC -SSM licensing requirement, model ASA 5510 with security plus license is able to support 2 context. So if i split my firewall like what i mention in question, what exactly number of context do i own (admin, context A, context B)?
Question 3: For CSC-SSM module in multi context mode, so the management port of CSC SSM must attach at admin context?
Question 4: After configured all the policy and traffic to scan, how exactly i should do in order apply this policy to the interface? Should i only enable at admin context, then firewall service-policy rules, and apply it global, OR should i also do the same action on context A and Context B?
I have a Cisco ASA 5520 that I'd like to be able to connect directly to our gigabit fiber connection (we're currently connected through a media converter that's causing problems). I've found the following:Cisco ASA 5500 Series 4 Port Gigabit Ethernet Security Services Module [URL]. I only need a single fiber connection, as opposed to the 4 copper + 4 fiber.
View 1 Replies View RelatedBuilding was recently upgraded from cat3 to cat6 wiring and I'd like to ssh into each Cisco C3750 stack and change every port on the stack to autonegotiate. I can release each port one at a time by doing "no speed" and "no duplex" after selecting each port (interface fastethernet x/x/x) , but it's taking forever as there are many stacks and each stack has a number of 24 and 48 port switches. The stacks are a mix of fastethernet and gigabit ports (C3750 and C3750G switches) if that changes anything command wise.
View 2 Replies View Related