Cisco Switching/Routing :: C3750 - Ethernet Port Goes To Err Disable Mode
Dec 6, 2011
I have stacked WS-C3750E-24PD with Ten Gigabit Ethernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it. One of the Ten Gigabit Ethernet ports, goes to err-disable mode with following errors on that specific ports.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm. (DROmx-1-1)
I have gone through some of CSC forums like {URL}. The workaround is to "Remove the X2 or SFP from the inactive up link port" which is not in my case.
View 9 Replies
ADVERTISEMENT
May 10, 2013
In our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies
View Related
Oct 11, 2012
I have a new building to add to our campus and I have been encouraged to run single mode fiber. All of my other buildings are connected with multi-mode fiber. I just want to make sure i will not have an issue if I run single mode to the new building with SM SFP's.
View 2 Replies
View Related
Dec 13, 2012
After powering up a WS-C3750-48PS switch, Normal POST LED flashing of lights does not happen, instead the switch is stuck in SYST Mode on the front panel. My attempt to hold down the mode button upon powering up for 15 sec fails to reboot the switch. I cannot console to the switch. Is this switch unrecoverable? Should I RMA with TAC?
View 5 Replies
View Related
Feb 8, 2012
We've just purchased a WS-C3750-24FS-S, only to find that the 100baseFX ports will not work over Single Mode fibre, backhaul links. Any way or a device that convert from MM to SM?
View 2 Replies
View Related
Aug 3, 2012
I have a Cisco 4500 as my core switch and there are two sup eng in this core. However, I noticed that the redundant sup is in diable mode rather than Hot Standby.
I have tired to enable the module but I am not able to do that.
The sup of my core is: WS-X45-SUP6L-E
View 1 Replies
View Related
Jun 22, 2012
I have couple C2960G and C3750. Is there any way to filter (on ingress port) type of traffic? I would like to allow IP only, and discard (i.e.) IPX, or other garbage, that any device can produce.I have tried to find something about this, but only thing I have found is feature : protocol filter, which doesn't seems to be working on my hardware.
View 6 Replies
View Related
Sep 27, 2012
I am having an issue on a Cisco 3750 stack where when the stack master is rebooted, all my lacp port-channels drop and then come back up again. After doing some investigation It seems that it is happening because of lacp using the stack master mac-address as part of the system-id, so when the stack master reboots, the stack mac changes. I see that there is the command: stack-mac persistent timer 0
There is this warning about using this command:
When you configure this feature, a warning message displays the consequences of your configuration. You should use this feature cautiously. Using the old master MAC address elsewhere in the domain could result in lost traffic.
My question are:
Are there any other consequences to using this command (apart from moving the switch/mac to another location in the network)It mentions 'If the entire switch stack reloads, it acquires the MAC address of the master as the stack MAC address' Is this still the case if you have the stack-mac persistent timer to 0? Does using channel-group mode on for the port-channels still use the same mechanism of having a system-id? (Will the channels flap using 'mode on' when rebooting the stack master.
View 4 Replies
View Related
Nov 12, 2011
Why I cannot ping vlan when no port connect to switch.
View 3 Replies
View Related
Jan 14, 2012
I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies
View Related
Aug 2, 2012
I have several SF300 switches deployed (SF300-08, SF300-24P). They are connected to IP Telephones (NEC) which communicate with the switch for auto voice VLAN on LLDP. The problem I am experiencing is that periodically the IP telephones are rebooted by the telephone vendor and when they do the switch puts that port into "Locked" port security mode and discards all traffic to the port. The IP telephones of course do not work. In other switch models, I have seen the ability to enable / disable port security switch wide or on a port by port basis. This model does not appear to have this feature. How to disable or why the phones would cause the switch ports to "lock"? There is usually one PC attached to each phone.
View 1 Replies
View Related
Mar 1, 2010
I have upgraded a couple of 2960G switches to 12.2.52SE and now discovered that TCP port 4786 is open on the switches.
I have looked in the document{URL}, trying to find a way to disable this function/port, but didn't find anything useful. Any way to disable this function/port?
View 3 Replies
View Related
Jan 18, 2012
Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies
View Related
Jun 20, 2012
I have a Cisco 2960G switch and one of the ports was configured with srr-queue bandwidth limit 90 - I need to remove this bandwidth limiting from this interface. [code]
View 2 Replies
View Related
Jan 25, 2012
I am testing 2960 24 S with storm-control and Errdisable Port timer interval 60s , connected HUB on fa0/17 to make traffic / loop.After Strom Control detection the interface goes down thats ok after 60s they will try to recover the interface and going up although the loop is still there.For my understanding if the interface detect still a loop on that interface they will disable the port again for 60s and will check again. [code]
View 7 Replies
View Related
Jun 29, 2012
We have a number of 3750 stacks used as access layer switches connecting Siemens VOIP phones and then a PC that connects to the phone.
For example if I plug PC A to the phone that connects to port 13 I pick up an IP addressand all works as predicted now if I plug in PC A to any other VOIP phone that connect to another port on the same switch it goes in error disable state ITs like the switch is holding my PC mac address and locks it down with the port which in my case is Gi2/0/13.
interface GigabitEthernet2/0/13
switchport access vlan 726
switchport mode access
[Code].....
View 7 Replies
View Related
Aug 1, 2012
I am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down
Err-Disable - Port goes into err-disable state (securedown)
HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
Equipment:
2x Cisco 1921 series routers
3x Cisco 2960 POE switches stacked
View 1 Replies
View Related
Oct 11, 2012
We have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
View 3 Replies
View Related
Mar 15, 2012
we have a scenario that consists of a Cisco 4507 series core switch with more than 20 vlans which is connected to a C2960G switch( in a nearby building) using a trunk by a fiber connection. Up to this point everyhting is fine . VTP domain is configured on the core switch and we have all of the 20 vlans present correctly on the edge 2960G wich is part of course of this same VTP domain.the fiber connection goes from core switch to a "in the middle location" where we have a fiber patch panel that is connected in a jumper style to another fiber patch panel going to the destination building where the C2960G sits.
Now imagine that Fiber connection from this middle location to the destination C2960 edge switch is down for any possible reason meanwhile the fiber connection from Core switch 4507 to the middle location is still intact.In the same time, in this middle location , we do have a wireless connection which links 1 Cisco 3750G switche ( a different infrastructure and different VTP domain) to another C3560G switch which sits on the same Room in the nearby destination building where we have the edge C2960G, An idea came to me is to connect one of the fiber port (core) in the intact fiber patch panel coming from Core switch 4507 TO an access vlan configured switchport in the 3750G switch ( this switchport will belong to a vlan designed only to trasmit the vlans on the trunk coming from 4507 core switch say VLAN 10) then connect one VLAN 10 access switchport to the destination C2960 edge switch ( the switchport on the c2960G is still a trunk)Will this solution work and all of the 20- 4507 core switch vlans arrive to the destination C2960G ? Or we do need something that tags the 2 VLAN 10 switchports like switchport dot1q tunnel like QinQ
View 2 Replies
View Related
Jan 14, 2013
I'm working at a company that has several 6509 switches running CatOS. They have two of the 6509's running in vtp server mode and the rest as clients. I set up a new vlan from one of the vtp servers and it propagated out. The problem comes when I try to assign a port on one of the vtp clients to this new vlan. It gives me an error that the switch must be in vtp server mode to add/delete vlans. I'm not trying to add/or delete a vlan just trying to add a port into an existing vlan. I'm hesitant to put the switch in vtp server mode. Is this a CatOS thing or is there a specific command to accomplish this?
View 5 Replies
View Related
Nov 15, 2012
What should the duplex mode to be set on a routed port gi0/21 that are running HSRP ? I try setting the gi0/21 to full, but it caused the port to be down. The only way for the port to be up is setting it to half duplex.
Cisco 3750 Switch
==============
interface GigabitEthernet0/21
no switchport
ip address 10.200.104.34 255.255.255.248
[Code].....
View 2 Replies
View Related
Jun 19, 2012
I'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies
View Related
Mar 23, 2013
Devices are 3750-24TS Switches, software version is 12.2(55)SE6. how to troubleshoot this issue, I have a pair of ports which are not bundling, no matter what. Is the same behavior with LACP or PAgP. In this outputs I have only the PAgP case.
Output is similar to:
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
12 Po12(SD) PAgP Fa1/0/23(I) Fa1/0/24(I)
Configuration on ports is simple:
SW1:
interface FastEthernet1/0/24
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 12 mode desirable
[code]....
View 3 Replies
View Related
Mar 5, 2013
I am trying to configure a 3500XL switch (and I know its old). I get to the int fa 0/1 line and thats where it all stops working.
switch#(config-if)#switch port mode access
switch#copy run start
or
switch#(config-if)#switch port mode access
switch#sh run int fa 0/1
It will show the configuration for port fa 0/1 as if I hadn't entered the "switch port mode access" command. Or any other command for that matter. Why the switch is not holding configuration and seemingly loses it as soon as you exit out of each interface?
View 4 Replies
View Related
Jan 11, 2012
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies
View Related
Dec 29, 2012
I have a Cisco 2851 router and need an additional gigabit Ethernet port. How to get the part number I need to order?
View 3 Replies
View Related
Jan 25, 2012
How to remove the config from an ethernet port on a Nexus 5548 - send it back to factory default.
View 1 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
Aug 15, 2012
I need to find out what is killing my Ethernet wan circuit urgently, It is a Ethernet trunk port with v lans tagged across it.
its a 3560x switch.
I configured span with the replicate keyword, but I'm not seeing all the traffic I'm sure.
I'm using wire shark.
Is there anything I can do to find what is causing this?
View 2 Replies
View Related
Oct 23, 2011
I have a 2610 router. How can I tell if the built-in ethernet port is only a 10BASE-T or if it's a 10/100 port? Is there a "Show" command to give me this information or did it only come one way? I have found conflicting information on this :-( If it's only 10BASE-T, can I upgrade it to 10/100?
View 8 Replies
View Related
Dec 18, 2012
I have a 2821 router and need to add another Ethernet port.
However, all the Ethernet modules seem to be End of Sale and the suggested replacements are only compatible with the ISRg2 range.
View 2 Replies
View Related
May 19, 2013
SW1#show interfaces fastEthernet 0/14 counters errors
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Fa0/14 6682 140364 0 306468 0
Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants
Fa0/14 0 0 0 0 180103 0 2798
[code]....
View 5 Replies
View Related
Feb 21, 2013
I have a problem to solve in our data center, see attached drawing. HW: Our core switches consists of two stacked C3750 with ip routing. What I want to do is probably simple but I haven't been able to figure out the best method.
VLAN10 and VLAN20 should not be able to communicate with each other. (ACLs?)VLAN10 will have it's own default route/firewall. Both VLAN10 and VLAN20 should be able to send server backups to server in VLAN30. All 3 V LANs come in on a trunk from a pair of stacked C2960-S. I need it to be able to scale if we have 50 VLANs for instance, hopefully without long complicated ACLs. I've been considering VRF's, PBR but can't decide what's the simplest solution to this problem. I have never done this before so I would prefer to start off on the right foot.
View 1 Replies
View Related
