Cisco Switching/Routing :: 3500XL - Configuration Switch Port Mode Access
Mar 5, 2013
I am trying to configure a 3500XL switch (and I know its old). I get to the int fa 0/1 line and thats where it all stops working.
switch#(config-if)#switch port mode access
switch#copy run start
or
switch#(config-if)#switch port mode access
switch#sh run int fa 0/1
It will show the configuration for port fa 0/1 as if I hadn't entered the "switch port mode access" command. Or any other command for that matter. Why the switch is not holding configuration and seemingly loses it as soon as you exit out of each interface?
View 4 Replies
ADVERTISEMENT
Mar 4, 2012
Can I have two different routers (different subnets) on one cisco 3500XL switch and still be able to communicate between the two? If so how can I do it?
View 8 Replies
View Related
Sep 5, 2012
My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies
View Related
Dec 8, 2011
Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
View 1 Replies
View Related
Feb 23, 2012
have a Switch I bought off a guy at work. Just to get into the Switching world of Cisco. He doesnt know the password on it and i cant reset the switch. I would like to mess around with it more but it doesnt load the flash or helper. It just sits there and holds. I have tried the password recovery and everything. Trust me, everything is correct, but it wont work for me. I cant load a new image to it because I dont have access to a server to get it from.
Base ethernet MAC Address: 00:0a:8a:94:58:c0Xmodem file system is available.
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init load_helper boot
switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4û
View 2 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
Feb 20, 2013
i have new project in hospital with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work first the 2 core switch for redundancy then each catalyst switch 2960 connected to the core with 2 uplink each uplink for each core switch that way i have rendundancy in the connection then i need one vlan ?i need to configure this switch to work perfectly with each other in best redundancy mode?
View 2 Replies
View Related
Jun 19, 2012
I'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies
View Related
May 12, 2013
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
View 9 Replies
View Related
Oct 29, 2011
I read quite a few documents on configuring SPAN on a cisco switch but none of them mention any limitations or any kind of CPU load it can have on a switch. I need to configure this on one of our switches and would like to know if there are any implications related to SPAN.
View 5 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
May 29, 2013
Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
View 2 Replies
View Related
Mar 15, 2012
we have a scenario that consists of a Cisco 4507 series core switch with more than 20 vlans which is connected to a C2960G switch( in a nearby building) using a trunk by a fiber connection. Up to this point everyhting is fine . VTP domain is configured on the core switch and we have all of the 20 vlans present correctly on the edge 2960G wich is part of course of this same VTP domain.the fiber connection goes from core switch to a "in the middle location" where we have a fiber patch panel that is connected in a jumper style to another fiber patch panel going to the destination building where the C2960G sits.
Now imagine that Fiber connection from this middle location to the destination C2960 edge switch is down for any possible reason meanwhile the fiber connection from Core switch 4507 to the middle location is still intact.In the same time, in this middle location , we do have a wireless connection which links 1 Cisco 3750G switche ( a different infrastructure and different VTP domain) to another C3560G switch which sits on the same Room in the nearby destination building where we have the edge C2960G, An idea came to me is to connect one of the fiber port (core) in the intact fiber patch panel coming from Core switch 4507 TO an access vlan configured switchport in the 3750G switch ( this switchport will belong to a vlan designed only to trasmit the vlans on the trunk coming from 4507 core switch say VLAN 10) then connect one VLAN 10 access switchport to the destination C2960 edge switch ( the switchport on the c2960G is still a trunk)Will this solution work and all of the 20- 4507 core switch vlans arrive to the destination C2960G ? Or we do need something that tags the 2 VLAN 10 switchports like switchport dot1q tunnel like QinQ
View 2 Replies
View Related
Oct 21, 2012
I have one cisco 4507R+E.My question is if the IOS of the acive SUP crushed and the switch is running through it's second SUP then how to restore the IOS of the first SUP.Also how to access the ROMON mode of the crushed SUP when switch is running through second SUP.
View 1 Replies
View Related
Jan 20, 2013
Can I configure the Port at the ASA 5050 from Mode: access Port to trunk during the FW is running in a production area without console access ?As I know at the 5505 ist should work?
View 3 Replies
View Related
Feb 21, 2012
cant assign cisco switch 3560G port g0/1to access vlan 10
main-switch(config-if)#switchport access vlan 10 Command rejected: Gi0/1 not a switching port.
View 5 Replies
View Related
Feb 14, 2013
Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies
View Related
Jan 15, 2013
We just installed a hosted VOIP system using Cisco 7900 series IP phones. We are having a strange issue with a few computers where they pull DHCP information from our VOIP provider's DHCP server on the Internet and not our LAN DHCP server.
The switchports areconfigured as: switchport mode access
My rationale behind this is that the phones would use CDP to get their VLAN info from the providers Cisco router and the PCs would just ride on the default VLAN. But this is not the case. Computers randomly keep getting DHCP info from the provider's router. Do I have to use voice vlan x and make the switchports trunks?
View 6 Replies
View Related
Apr 22, 2012
I've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies
View Related
Apr 27, 2012
I have a POE switch running 12.0(5). I have port 24 connected as a trunk connected to the main switch. I need to add an ip address on vlan 21 which is where the network vlan is. I created it but I can not seem to enable it. I have issued the no shut command several times, but doing "sh ip int brief" it keeps showing up as administively down.
View 13 Replies
View Related
Jan 9, 2013
I am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
View 8 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Jul 10, 2012
I'm configuring a catalyst 3500XL, but I'm having a problem, when I connect an ip phone it works just fine but if I connect a computer to the pc port in the phone the computer doesn't get an ip address. The switch is configure with two vlans Voice and Data and is connected from fa0/24 to a Catalyst 3560 fa0/46. I did configure both ports as trunk.
View 9 Replies
View Related
Oct 14, 2012
I am trying to trunk between a 3Com 4800g and a Cisco 3500xl. I can get the a PC that connects to a vlan 1 port on thecisco switch to connect to the 3com switch and get connectivity. However, I cannot get anthing on the cisco switch that is on vlan 2 to connect and get dhcp. I am not a 3com guy, so I am not familiar with the command and configs.We have 2 vlans on both switches: Vlan 1 is Admin and Vlan 2 is Student.
View 17 Replies
View Related
Mar 7, 2012
I have an old Cisco 3500XL I am using for my home lab, but was wondering can I use the fiber ports to connect to my PC. I have to correct NIC interfaces but no link indication. I did make sure the port was no down, but sill not link.
View 8 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Jul 7, 2012
i have several cisco 3500XL switches with trunking. I created a VLAN lets say 20 which purpose is for wireless clients. I installed wireless controller with 4 APs and controllers sees all 4 APs. Controller is also DCHP server. When wireless client authenticates it's DCHP requests in not getting to DHCP server (controller). If i connect all equipment in non managed switch everything works.
View 10 Replies
View Related
Jul 18, 2012
I have several Cata 3500XL switches connected to one 1 HP L3 switch which is connected Sonicwall router. Vlan1 has subnet of 10.10.0.0/24 and Microsoft DCHP server lays inside VLAN1.
Now i want to add VLAN11 (192.168.10.0/24) as second data VLAN but DHCP requests should go to microsoft DCHP server.
This is what i did:
Configured VLAN11 IP on each cisco switch
IP default gateway with IP from other subnet (i guess this is bad since maybe it should be IP of VLAN11 on HP L3 switch?)
Trunk ports are configured to pass everything on cisco switches
On VLAN11 i configured IPhelper IP to be MS DHCP server on each Cisco switch
I haven't tested this yet but i have problem in process.I can't ping VLAN11 IPs between switches (i configured VLAN1 and VLAN11 with IP). When client plugs computer to a port that belongs to VLAN11 will i be sure that client will get IP from the 192.168 range or there is possiblity that he gets IP from the management VLAN range?
View 4 Replies
View Related
Mar 20, 2013
Need your expert input in sorting out the below problem.I have a cisco 6513 switch which is going into SP mode after a reboot whci i have done during BCP activity in my organization.Below are the log for your reference.
Code...
View 1 Replies
View Related
Oct 14, 2012
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies
View Related
