I'm configuring a catalyst 3500XL, but I'm having a problem, when I connect an ip phone it works just fine but if I connect a computer to the pc port in the phone the computer doesn't get an ip address. The switch is configure with two vlans Voice and Data and is connected from fa0/24 to a Catalyst 3560 fa0/46. I did configure both ports as trunk.
View 9 RepliesI have a POE switch running 12.0(5). I have port 24 connected as a trunk connected to the main switch. I need to add an ip address on vlan 21 which is where the network vlan is. I created it but I can not seem to enable it. I have issued the no shut command several times, but doing "sh ip int brief" it keeps showing up as administively down.
View 13 Replies View RelatedI've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies View RelatedCan I have two different routers (different subnets) on one cisco 3500XL switch and still be able to communicate between the two? If so how can I do it?
View 8 Replies View RelatedI am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
I am trying to trunk between a 3Com 4800g and a Cisco 3500xl. I can get the a PC that connects to a vlan 1 port on thecisco switch to connect to the 3com switch and get connectivity. However, I cannot get anthing on the cisco switch that is on vlan 2 to connect and get dhcp. I am not a 3com guy, so I am not familiar with the command and configs.We have 2 vlans on both switches: Vlan 1 is Admin and Vlan 2 is Student.
View 17 Replies View RelatedMy understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies View RelatedI have an old Cisco 3500XL I am using for my home lab, but was wondering can I use the fiber ports to connect to my PC. I have to correct NIC interfaces but no link indication. I did make sure the port was no down, but sill not link.
View 8 Replies View RelatedBase ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
have a Switch I bought off a guy at work. Just to get into the Switching world of Cisco. He doesnt know the password on it and i cant reset the switch. I would like to mess around with it more but it doesnt load the flash or helper. It just sits there and holds. I have tried the password recovery and everything. Trust me, everything is correct, but it wont work for me. I cant load a new image to it because I dont have access to a server to get it from.
Base ethernet MAC Address: 00:0a:8a:94:58:c0Xmodem file system is available.
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init load_helper boot
switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4û
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies View Relatedi have several cisco 3500XL switches with trunking. I created a VLAN lets say 20 which purpose is for wireless clients. I installed wireless controller with 4 APs and controllers sees all 4 APs. Controller is also DCHP server. When wireless client authenticates it's DCHP requests in not getting to DHCP server (controller). If i connect all equipment in non managed switch everything works.
View 10 Replies View RelatedI have several Cata 3500XL switches connected to one 1 HP L3 switch which is connected Sonicwall router. Vlan1 has subnet of 10.10.0.0/24 and Microsoft DCHP server lays inside VLAN1.
Now i want to add VLAN11 (192.168.10.0/24) as second data VLAN but DHCP requests should go to microsoft DCHP server.
This is what i did:
Configured VLAN11 IP on each cisco switch
IP default gateway with IP from other subnet (i guess this is bad since maybe it should be IP of VLAN11 on HP L3 switch?)
Trunk ports are configured to pass everything on cisco switches
On VLAN11 i configured IPhelper IP to be MS DHCP server on each Cisco switch
I haven't tested this yet but i have problem in process.I can't ping VLAN11 IPs between switches (i configured VLAN1 and VLAN11 with IP). When client plugs computer to a port that belongs to VLAN11 will i be sure that client will get IP from the 192.168 range or there is possiblity that he gets IP from the management VLAN range?
I am trying to configure a 3500XL switch (and I know its old). I get to the int fa 0/1 line and thats where it all stops working.
switch#(config-if)#switch port mode access
switch#copy run start
or
switch#(config-if)#switch port mode access
switch#sh run int fa 0/1
It will show the configuration for port fa 0/1 as if I hadn't entered the "switch port mode access" command. Or any other command for that matter. Why the switch is not holding configuration and seemingly loses it as soon as you exit out of each interface?
giving unauthorized access and no internet access
Windows IP Configuration
Host Name . . . . . . . . . . . . : KHANBALOCH-PC
Primary Dns Suffix . . . . . . . :
[Code].....
We have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
Our 871 no longer allows us to make changes to it. I was told the contract ran out, so I renewed it and Cisco support then added the contract to my serial number. What now? Is there a step required to have the router check in with Cisco so that it becomes "unlocked" for me to make changes?
View 1 Replies View RelatedI have a 3945 router with two interfaces connected to my firewall, one to the management interface and another to my dmz. I'm running eigrp between all my network devices. The problem I'm running into is when I try to ssh to the management interface of the 3945 the traffice hits the firewall, then goes right to the management interface as it should, but the return traffic is trying to use the dmz interface since that is how the router knows to get back to my computers network. I created 2 route-maps to try and address this issue. [code] I've applied the MANAGE_IN route-map to all interfaces that might have inbound traffic destined for the management network and applied the MANAGE_OUT route-map to the management interface. The MANAGE_IN policy appears to be functioning correctly, the MANAGE_OUT doesn't appear to be functioning correctly. When I look at traffic from my host going to the management interface I see it still trying to return through the dmz interface.
View 11 Replies View RelatedI have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies View RelatedI created the configuration below to limit the bandwidth, but doesn't work
Qos - 3750
!
mls qosmls qos map policed-dscp 10 to 8!class-map match-all Testmatch access-group name ACL!policy-map QOSdescription Limit 10M set ip dscp af11 police
[Code]....
we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]
From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?
I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
I am building up vPC on 2 x Nexus 3048 and found that it did not work properly.The current config as follows,
1. OS: n3000-uk9.5.0.3.U2.2.bin
2. Peer link: 10 x 1G (E1/1 - E1/10) on both devices (I am wondering that 1G interface supports vPC Peer-Link. I heard that upgrading to U3.2 image will work for 1G rather than 10G... )
3. They can ping each other via management IPs
4. Edge switches vPC have not been built yet (I am focusing on Peer-Link and vPC role selection)
[code]....
c3750e-universalk9-tar.150-1.SE on 3750x
username cisco privilege 15 secret cico
aaa new-model
aaa authentication login default local
[Code]....
Console and telnet don't seem to auto authorize to level 15, I end up at level 1, I'm forced to use enable command.
Rolling back to c3750e-universalk9-mz.122-58.SE2 fixes it. Going back to c3750e-universalk9-tar.150-1.SE breaks it again.
is there some new behavior in cat 15 code (couldn't find it in config guide)? maybe a bug (couldn't find one)?
my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
I've been working on a 3560 that doesn't seem to map dscp values to a new value: mls qos map dscp-mutation ToR1 22 24 to 46
[Code]....
On the router on the other side, I created an acl that matched on dscp 46, but it doesn't match on it. I've tried moving the mutation map to the ingress interface and I've tried setting dscp with a service policy instead of marking COS and using internal dscp. Where is the mutation map supposed to be placed: ingress or egress? Also, I added an entry in the acl on the router to see if I was mapping to dscp 24, and I am:
[Code]....
So it seems like the mutation map is being ignored completely. Any reason why?
My network has two connections to a third party via links on two seperate ASA , one in location A and one in location B. The link in location A is the primary connection and the other in location B should be used by only two terminals (term1, term2) in location B. ASA are running OSPF and are redistributing static routes as metric-type 1 in OSPF. In order to achive the aforementioned goal, I have configured a route-map on ASA location B, that sets the metric for the route towards the third party to a high value (100). This way, all routers, even those in site B prefer the exit through location A (metric about 24).
I have checked that my routers correctly have the route to the 3rd party through location A, and the OSPF database has records for the network from both locations.In location B, I have configured the following route-map (on 6509)
route-map PREFER-LOCAL-ROUTER permit 10
match ip address XXX
set ip next hop locationB-ASA
int vlanYYYY
ip policy route-map PREFER-LOCAL-ROUTER
[code]....
From the terminals (term1 and term2) I have tried a traceroute towards the 3rd party's subnet, but I don't get any match neither on the access-list nor on the route-map. Unfortunately I have no other way to test that my configuration is correct, since the application on the terminals, that should access the 3rd party network, is not currently running.
I also addedd the statements below to the access-list, because of the test with tracert:
permit icmp host term1 route_to_3rd_party 0.0.255.255
permit icmp host term2 route_to_3rd_party 0.0.255.255
Nothing changed...Is there something wrong with the above config? Is there a chance that there is a problem with the IOS, that simply doesn't show any hits?
I have upgraded my C3560-PS-S switch to the latest IOS version 12(2)55-SE4 and it is not providing PoE anymore? It used to work before this upgrade? I searched Cisco bugtrack and there is bug defined for this IOS/Switch.
Switch(config-if)#do show power inline Available:370.0(w) Used:0.0(w) Remaining:370.0(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa0/1 auto off 0.0 n/a n/a 15.4
Fa0/2 auto off 0.0 n/a n/a 15.4
Fa0/3 auto off 0.0 n/a n/a 15.4
Fa0/4 auto off 0.0 n/a n/a 15.4
Fa0/5 auto off 0.0 n/a n/a 15.4
Fa0/6 auto off 0.0 n/a n/a 15.4
Fa0/7 auto off 0.0 n/a n/a 15.4
Fa0/8 auto off 0.0 n/a n/a 15.4
Fa0/9 auto off 0.0 n/a n/a 15.4
Fa0/10 auto off 0.0 n/a n/a 15.4
Fa0/11 auto off 0.0 n/a n/a 15.4
Fa0/12 auto off 0.0 n/a n/a 15.4
Fa0/13 auto off 0.0 n/a n/a 15.4
Fa0/14 auto off 0.0 n/a n/a 15.4
Fa0/15 auto off 0.0 n/a n/a 15.4
Fa0/16 auto off 0.0 n/a n/a 15.4
Fa0/17 auto off 0.0 n/a n/a 15.4
Fa0/18 auto off 0.0 n/a n/a 15.4
Fa0/19 auto off 0.0 n/a n/a 15.4
Fa0/20 auto off 0.0 n/a n/a 15.4
Fa0/21 auto off 0.0 n/a n/a 15.4
Fa0/22 auto off 0.0 n/a n/a 15.4
Fa0/23 auto off 0.0 n/a n/a 15.4
Fa0/24 auto off 0.0 n/a n/a 15.4
I've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies View RelatedWe have 10 ADSL lines and 5 of them goes in the load balancer (One gateway) and the rests are used as default gateways for internet access. We use ADSL routers as access points for internet, but those routers should be part of our network and should be given an address in order for them to act as default gateways for internet access. I'm facing a real prob with the ADSL routers Linksys WAG54G2 because they doesn't support a subnet mask 255.255.0.0 Any recommendation for an ADSL router model that support a netmask 255.255.0.0 ?
My cisco 2811 router interface configuration ip address: 172.20.0.1 255.255.254.0.Load balancer output lan ip address: 172.20.0.5.My ADSL routers will be in the following range : 172.20.0.6 - 172.20.0.10
we have three separated network segments going to one Cisco 3750 switch all is L2 .. from this switch is 100 mbit uplink.we need to apply some Qos mechanism not to saturate line by traffic from one network.. Configuration from various reason CANNOT be done on switch where 100Mbit line is terminated.. so all must be done on SW1,2,3..Correct me if iam wrond but as switches doesnt see traffic from other network iam affraid only think we can do is limit bandwidth on links going into SW1,2,3 to 33 Mbit.I found commad srr-queue bandwidth limit.But links going to SWs are 1Gbit so if i force bandwidth to 10% (minimum what command allows) its 100 Mbit..If I force speed on those links to 100Mbit and than apply srr-queue bandwidth limit to 30% doest it work.??. Will srr-queue bandwidth limit speed to 30Mbit?? Or srr-queue bandwidth limit is calculated from maxim speed of interface?
View 1 Replies View Related