Cisco Switching/Routing :: WS-C6509-E Doesn't Remove IPs From ARP
Mar 25, 2012
we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]
From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?
View 2 Replies
ADVERTISEMENT
Oct 14, 2012
We would like to install a WS-SVC-WISM2-1-K9 in each of our 2 WS-C6509-E chassis. Both of these have supervisor 720 engines installed. One in each chassis.From what I have read we need to upgrade the IOS to 12.2.33 SXJ4. Is this correct?If this is true then what are the memory requirements for the upgrade to this IOS version. Below is the output from Show version?Is there sufficient memory instqalled to do this install?
View 3 Replies
View Related
Mar 9, 2012
we plan to implement VSS on our datacenters (C6509/Sup720), in order to remove L2 loops (currently, access layer are C3750 stacks, which could evoluate for N5K/N2K). I would like to have some feedbacks about VSS stability. Some years ago, I have seen some bugs with this technology in another company, so I am still not totally comfortable to use it in the datacenter.
View 0 Replies
View Related
Apr 4, 2012
We plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
unsecure layer
Proxy layer
Secure layer
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?
View 1 Replies
View Related
Jan 13, 2013
I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.
[Code] .......
View 5 Replies
View Related
Feb 26, 2012
Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.
View 1 Replies
View Related
Sep 26, 2012
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
View 2 Replies
View Related
Apr 1, 2013
I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but i dont know it and is it attack?also same seq no switch gots it?what is problem?
View 2 Replies
View Related
Dec 22, 2011
Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
qa-c6509-c(config)#monitor session 1 filter ? vlan SPAN filter VLAN
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.
View 4 Replies
View Related
Nov 25, 2012
I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.
View 2 Replies
View Related
Sep 9, 2009
I need those two stencils.I have checked here [URL] but:
- the one for the C6509-E is not there
- the one for the supervisor does not work properly (misaligned anchor points).
View 2 Replies
View Related
Oct 21, 2012
I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
View 2 Replies
View Related
Jan 2, 2012
I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
and vlan:
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
165 test5 active Gi7/14
But I can't ping this IP address and show ip route shows:
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
Known via "static", distance 254, metric 0 (connected)
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?
View 9 Replies
View Related
Sep 10, 2009
I am trying to figure out what is heat dissipation of a C6509-E configured as follows:
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
1) The power calculator says 13630 BTU/h
2) Manual calculation says: [code]
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?
View 2 Replies
View Related
Sep 19, 2012
Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on. This layer 3 switch will be used to connect to servers.
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
[Code]....
View 6 Replies
View Related
Mar 20, 2012
We have two c6509 budled in VSS. I have noticed randomly high usage of CPU, sometimes up to 99% in peaks. I have found that it can be generated by SNMP engine. So I unconfigure all SNMP things. But situation is the same. I would like to know if this state is OK or not. CPU shows are enclosed in file.
View 1 Replies
View Related
Aug 8, 2012
We are facing issue of getting very high CPU utilization for the VSS Switch model WS-C6509-E some times approx 100%.Attaching here show tech-support taken later after CPU normal along with show logging, show cpu sorted.HCAINNOI01XXXCS0001#sh proces cpu | ex 0.0%CPU utilization for five seconds: 100%/13%; one minute: 90%; five minutes: 91%PID 5Sec 1Min 5Min Process16406 91.2% 75.2% 76.2% ios-base16426 1.7% 1.4% 1.4% udp.proc16429 0.3% 0.3% 0.3% raw_ip.proc16432 2.8% 3.1% 3.1% cdp2.iosproc
View 3 Replies
View Related
Nov 27, 2011
we have cisco WS-C6509-V-E with IOS version 12.2(33)SXI4; s3223_rp_IPSERVICESK9_WAN_M) running on a switch. I am trying to configure the command "mac-address-table synchronize" under global config mode. But when I enter the command Cisco(config)#mac-address-table ?It doesn't show the synchronize option?
View 3 Replies
View Related
Nov 14, 2012
I am trying to find a command for dhcp snooping rate-limiting on a CatOS. The PFC card is PFC. PFC3B is said to support that command. But there seems no this command.
-6k> (enable) sh ver
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:26:46
[Code] ......
Up time is 1183 days, 1 hour, 41 minutes
View 3 Replies
View Related
Jan 14, 2013
We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
View 3 Replies
View Related
Oct 17, 2012
I've a big problem with a loss of packets ICMP sent by different hosts in differents VLAN. Here my architecture:
Core Switch : 2 Switch's C6509 (Version 15.0 (1) SY1)- Mode VSS - One lien VSL , the other link is defective.Access Switch: C3750 , Connected to Core Switch through 2 fibre optique wires.Topology: redundant ring
When I send consecutive ping message I found always a missing of packets . Furthermore When I insert the "show ip traffic" command., the parameter "bad hop count" increase after a loss of packets. I've 2 hosts connected in my network and they send packets with TTL =127.
In the Core Switch I haven't configured the MEC because it gave me troubles with the packets multicast.
View 1 Replies
View Related
May 11, 2012
I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies
View Related
Jun 8, 2007
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies
View Related
Dec 3, 2012
We have a pair of 6509's with duplicate ACL lists & entries.
1 = Version 12.2(33)SXI4a
2 = Version 12.2(18)SXF15a
I wanted to remove some logging that was on an entry on one of our extended ACL's. On 1 this worked fine with the no 400
400 <acl rule without log>
However on 2 it lets me carry out the no 400 command but when i go to add the 400 <acl rule without log> i get the error % Duplicate sequence number.sure enough when i perform the 'Show access-lists <Name>' it is still there!
I have tried the following:
Adding a duplicate ACL entry before it (399) without log and i still get hits on line 400Adding and removing the duplicate created line 399 (without logging) with no issues.Adding and removing a dupliacte ACL (without Logging) after (line 401) with no issues
It looks like it is just this line it seems to think it has removed but hasn't?!
I understand an option is to duplicate the ACL in a text editor remove line, delete the ACL and put the edit back in .....however i wondered if this is something known (bug).
View 11 Replies
View Related
Apr 30, 2013
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies
View Related
Aug 9, 2012
I have a 3500 XL switch with the following default gate IP address that i need to clear from the switch but not quite shore how to remove it.
I've removed the customer original Ip for security reason as this is an open discussion forum and just replaced with 1.1.1.1
switch#show ru
Building configuration...
Current configuration:
!
[Code].....
View 2 Replies
View Related
Jan 29, 2012
I have a 6509 running s72033_rp-ADVIPSERVICESK9_WAN-M version 12.2(33)SXH5. Four incorrect bgp aggregate-address statements were entered in which overlap. Attempted to remove the statements but they won't come out.
aggregate address 16.37.31.0 255.255.224.0 summary-only
aggregate address 16.37.30.0 255.255.224.0 summary-only
aggregate address 16.37.29.0 255.255.224.0 summary-only
aggregate address 16.37.26.0 255.255.224.0 summary only
I have entered in the correct statements and have no problem getting those in, removing them, and reentering them.
View 2 Replies
View Related
Jul 17, 2012
what is the best way to remove configs from ports (GigE or Fa) in a 6500 that we aren't using anymore (i.e. best way to return a port to default). Remove each line one at a time or is there a command to default a port?
View 2 Replies
View Related
Aug 12, 2012
I'm having trouble with a Cisco Catalyst 2950 Series Switch where by I'm following the procedure from Cisco's web site to remove the Banner and login information, url..
Each command is being accepted by the switch from following the information given within the help sheet above,the problem i have now is when i turn the power off then turn the switch back on I'm still getting the banner and login information even though i have follwed Cisco's help correctly.
View 2 Replies
View Related
Jan 23, 2011
We currently have two 6509's running in VSS, both switches have a WS-6748-GE module in slot 3. I'm in the processing of removing these modules. I will then be replacing them with a different module type, but I need to know how to remove the old configuration of the previous modules.
View 4 Replies
View Related
Feb 20, 2012
I have been given 2 x 3750 switches that were a stack, I need to keep the configs on both but how do I make them individual switches again and remove the stack info?
View 3 Replies
View Related
Mar 5, 2012
I have removed an embbedded service engine modole from an 2951 router, after reboot the rouiter. the service engine interface still appears; any command can I use to completely remove it.
View 2 Replies
View Related
May 2, 2013
is it easy to remove the 3750x stacking? i'd like to test one of them on a sunday and keep the other one on production. it's just two stack of 3750x, is it hard and do i really need to remove the cables on the back?
basically i need to put a different config for my testing, i gues i need to remove the cables right? and put it back on the stack before monday.
View 2 Replies
View Related
