Cisco Switching/Routing :: WS-C6509 / VLAN Interface Limit

Jan 2, 2012

I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
 
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
 
and vlan:
 
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
165  test5                                 active    Gi7/14
 
But I can't ping this IP address and show ip route shows:
 
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
  Known via "static", distance 254, metric 0 (connected)
 
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?

View 9 Replies


ADVERTISEMENT

Cisco Switching/Routing :: C6509 Loss Of Packets ICMP Sent By Different Hosts In Different VLAN

Oct 17, 2012

I've a big problem with a loss of packets ICMP sent by different hosts in differents VLAN. Here my architecture:
 
Core Switch : 2 Switch's C6509 (Version 15.0 (1) SY1)- Mode VSS - One lien VSL , the other link is defective.Access Switch: C3750 , Connected to Core Switch through 2 fibre optique wires.Topology: redundant ring
 
When I send consecutive ping message I  found always a missing of packets . Furthermore When I insert the  "show ip traffic" command., the parameter "bad hop count" increase after a loss of packets. I've 2 hosts connected in my network and they send packets with TTL =127.
 
In the Core Switch I haven't configured the MEC because it gave me troubles with the packets multicast.

View 1 Replies View Related

Cisco Switching/Routing :: 7606 / Limit Interface That Is Used By One Of Customers To 30M

May 15, 2012

I have a Cisco 7606 running 12.2.  I want to limit the interface that is used by one of our customers to 30M.

View 3 Replies View Related

Cisco Switching/Routing :: 6509-E - Rate Limit PPS On Interface?

Jun 8, 2013

How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance

View 2 Replies View Related

Cisco Switching/Routing :: QoS Limit Specific VLAN Within Trunk 4506

Jan 25, 2012

Need to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.

View 1 Replies View Related

Cisco Switching/Routing :: 4096 - Limit Number Of Vlan Trunk

Nov 15, 2011

a number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.

View 1 Replies View Related

Cisco Switching/Routing :: CAT 4006 VLan Routing Without Setting Interface IP?

Feb 26, 2013

We got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?

View 4 Replies View Related

Cisco Switching / Routing :: 1841 - How To Use Both 2 Interface For Two Different Vlan

Jan 3, 2013

we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).

Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.

see below configuration:

[code]...

View 5 Replies View Related

Cisco Switching/Routing :: 3845 NAT Translation In VLan Interface

Nov 20, 2011

I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]

View 8 Replies View Related

Cisco Switching/Routing :: VLAN Interface Quantity Of WLC 5508?

Apr 25, 2013

How many VLAN Interface can be create on a WLC Interface, e.g. GigabitEthernet 1?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6503 OSPF On Vlan Interface?

Oct 24, 2011

i'd like to configure OSPF on a Catalyst 6503 IOS 12.2.17.i habe an Gi1/9 with the ip address 192.168.97.30/24 and a VLAN 19 with the IP Address 192.168.19.0/24.I configured OSPF like this
 
router ospf 1
network 192.168.97.0 0.0.0.255 area 10.5.0.0
network 192.168.19.0 0.0.0.255 area 10.5.0.0
 
on the ospf peer is see that the adjaceny is established but i don't get the routes for the 192.168.19.0 network i checked the ip ospf interface vlan 19; i got ospf is not enabled on the interface then i tried to configure

int vlan 19
ip ospf 1 area 10.5.0.0
 
but it does not access ip ospf 1

View 3 Replies View Related

Cisco Switching/Routing :: 3560E / IP PIM Sparse-Mode On Vlan Interface

Sep 23, 2012

I'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface is already configured with IP PIM SPARSE-MODE.

View 2 Replies View Related

Cisco Switching/Routing :: Cannot Set Route-map On Interface Vlan In Non Default Vrf On 3750

Dec 12, 2012

Cannot set route map on interface vlan. which in non default vrf on Cisco 3750.IOS c3750-ipservicesk9-mz.122-55.SE.bin sdm prefer route in enable ip vrf users rd 200:0 route-target export 200:0 route-target import 200:0 interface Vlan201 description Users 1 ip vrf forwarding users ip address 10.31.76.1 255.255.252.0 ip helper-address 10.31.4.57 route-map fromuser permit 10 match ip address fromuser set ip next-hop 10.31.128.155 When I enter "ip policy route-map fromuser" to interface Vlan 201 I heve the message:
 
% Remove VRF configuration from interface Vlan201 first

View 5 Replies View Related

Cisco Switching/Routing :: Vlan And Physical Interface Counters 3560x

Dec 9, 2012

vlan interface and physical interface (that is serving for this vlan ) have different input/output counters, there is only one physical interface in this vlan .
 
sh int vlan 64
30 second input rate 9000 bits/sec, 9 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec

[Code]....

View 5 Replies View Related

Cisco Switching/Routing :: 3560 / Apply Acl Restrictions To The Vlan Interface Ip Address Itself

Nov 1, 2011

I've set up my 3560 to do routing.  Now, I'm looking for a way to apply acl restrictions to the vlan interface ip address itself. 

View 1 Replies View Related

Cisco Switching/Routing :: 6500 Show Interface Status Output As VLAN

Mar 5, 2013

I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
 
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.

View 5 Replies View Related

Cisco Switching/Routing :: How To Upgrade WS-C6509-E IOS

Oct 14, 2012

We would like to install a WS-SVC-WISM2-1-K9 in each of our 2 WS-C6509-E chassis.  Both of these have supervisor 720 engines installed.  One in each chassis.From what I have read we need to upgrade the IOS to 12.2.33 SXJ4.  Is this correct?If this is true then what are the memory requirements for the upgrade to this IOS version.  Below is the output from Show version?Is there sufficient memory instqalled to do this install?

View 3 Replies View Related

Cisco Switching/Routing :: 2900 - Nexus 7010 Layer 2 VLan 11 Active But Interface Shutdown

Sep 13, 2012

I understand the vlans on the catalyst side of the house on 2900 to 6500 Catalyst switches.
 
This 7010  running nx-os 5.1(3) I did not setup, but have to manage it.  Hasn't really been a proble till now.
 
My nexus 7010 has a Layer 2 only vlan 11. It is "Active" but the interface is "shutdown".  Yet, it is passing traffic across the directly connected  ports on the nexus 7010 and to other switches in my network.  Vlan 11 is being set out via VTP to all my switches and things are running fine.
 
I need to create another L2 only Vlan.  I can't seem to find any docs  that indicate that a Layer2 vlan Interface on nx-os should be in  "shutdown" mode as part of the setup. I do see in the docs where it has  to be set "Active" as part of the process.
 
Is this the correct way to seutp a L2 only vlan on nex-os? Leave the interface in "shutdown" but make it "Active"?
 
Mystery Vlan 4 and 6
The mystery deepens.  I have other L2 vlans ,Vlan4&6 that are NOT defined as "Interface Vlan4" in the nexus config, yet it is applied to GigE ports on the nexus and these Vlans 4/6is also being sent out VTP to all switches.  Even weirder is that these vlans have names associated with the numbers.  These are valid Vlans that were configured on the old 6509 before the Nexus was installed.
 
I have checked all switches, NONE are running in Server mode for VTP, all are in CLIENT. The nexus 7010 is the only device running in VTP Server mode. 

View 2 Replies View Related

Cisco Switching/Routing :: C6509 To Have Feedbacks About Vss Availability

Mar 9, 2012

we plan to implement VSS on our datacenters (C6509/Sup720), in order to remove L2 loops (currently, access layer are C3750 stacks, which could evoluate for N5K/N2K). I would like to have some feedbacks about VSS stability. Some years ago, I have seen some bugs with this technology in another company, so I am still not totally comfortable  to use it in the datacenter.

View 0 Replies View Related

Cisco Switching/Routing :: Impact Of ACL On C6509 CPU Utilization?

Apr 4, 2012

We plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
 
unsecure layer
Proxy layer
Secure layer
 
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
 
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
 
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?

View 1 Replies View Related

Cisco Switching/Routing :: WS-C6509-E High CPU Utilization

Jan 13, 2013

I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.

[Code] .......

View 5 Replies View Related

Cisco Switching/Routing :: C6509-E Do A Unexpected Reload

Feb 26, 2012

Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
 
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.

View 1 Replies View Related

Cisco Switching/Routing :: What Should Be Minimum IOS Version On WS-C6509-E

Sep 26, 2012

what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?

Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
 
(config)#logging ?  Hostname or A.B.C.D  IP address of the logging host  buffered             Set buffered logging parameters  buginf               Enable buginf logging for debugging  cns-events           Set CNS Event logging level  console              Set console logging parameters  count                Count every log message and timestamp last occurance  esm                  Set ESM filter restrictions  event                Global interface events  exception            Limit(code)

View 2 Replies View Related

Cisco Switching/Routing :: C6509-E / What Is Mean That Is Packet Capture?

Apr 1, 2013

I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but  i dont know it and is it attack?also same seq no switch gots it?what is problem?

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E Doesn't Remove IPs From ARP

Mar 25, 2012

we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]

From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?

View 2 Replies View Related

Cisco :: Routing Traffic From Non VLAN To VLAN On Same Interface?

Nov 21, 2012

i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this

View 10 Replies View Related

Cisco Switching/Routing :: Monitor ICMP Traffic On C6509?

Dec 22, 2011

Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
 
qa-c6509-c(config)#monitor session 1 filter ?  vlan  SPAN filter VLAN
 
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.

View 4 Replies View Related

Cisco Switching/Routing :: C6509 Switch Port Over Subscription

Nov 25, 2012

I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.

View 2 Replies View Related

Cisco Switching/Routing :: C6509-E And VS-S720-10G Visio Stencils?

Sep 9, 2009

I need those two stencils.I have checked here [URL] but:

- the one for the C6509-E is not there

- the one for the supervisor does not work properly (misaligned anchor points).

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E - Possible To Boot IOS From TFTP Server

Oct 21, 2012

I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration

View 2 Replies View Related

Cisco Switching/Routing :: What Is Heat Dissipation Of C6509-E Configured

Sep 10, 2009

I am trying to figure out what is heat dissipation of a C6509-E configured as follows:
 
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
 
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
 
1) The power calculator says 13630 BTU/h
 2) Manual calculation says: [code]
 
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E - Verification Of Services And Protocols

Sep 19, 2012

Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on.  This layer 3 switch will be used to connect to servers.
 
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)

[Code]....

View 6 Replies View Related

Cisco Switching/Routing :: C6K Randomly High CPU Usage C6509

Mar 20, 2012

We have two c6509 budled in VSS. I have noticed randomly high usage of CPU, sometimes up to 99% in peaks. I have found that it can be generated by SNMP engine. So I unconfigure all SNMP things. But situation is the same. I would like to know if this state is OK or not. CPU shows are enclosed in file.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved