Cisco Switching/Routing :: What Should Be Minimum IOS Version On WS-C6509-E

Sep 26, 2012

what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?

Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
 
(config)#logging ?  Hostname or A.B.C.D  IP address of the logging host  buffered             Set buffered logging parameters  buginf               Enable buginf logging for debugging  cns-events           Set CNS Event logging level  console              Set console logging parameters  count                Count every log message and timestamp last occurance  esm                  Set ESM filter restrictions  event                Global interface events  exception            Limit(code)

View 2 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Minimum Code Version For N55-M16UP?

Apr 28, 2013

give me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?

View 1 Replies View Related

Cisco Switching/Routing :: Minimum UPS For Catalyst 3560G-48-Poe?

Oct 2, 2012

We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport  I would think I should have more, but have not had any issues with a few power outages

View 1 Replies View Related

Cisco Switching/Routing :: How To Upgrade WS-C6509-E IOS

Oct 14, 2012

We would like to install a WS-SVC-WISM2-1-K9 in each of our 2 WS-C6509-E chassis.  Both of these have supervisor 720 engines installed.  One in each chassis.From what I have read we need to upgrade the IOS to 12.2.33 SXJ4.  Is this correct?If this is true then what are the memory requirements for the upgrade to this IOS version.  Below is the output from Show version?Is there sufficient memory instqalled to do this install?

View 3 Replies View Related

Cisco Switching/Routing :: C6509 To Have Feedbacks About Vss Availability

Mar 9, 2012

we plan to implement VSS on our datacenters (C6509/Sup720), in order to remove L2 loops (currently, access layer are C3750 stacks, which could evoluate for N5K/N2K). I would like to have some feedbacks about VSS stability. Some years ago, I have seen some bugs with this technology in another company, so I am still not totally comfortable  to use it in the datacenter.

View 0 Replies View Related

Cisco Switching/Routing :: Impact Of ACL On C6509 CPU Utilization?

Apr 4, 2012

We plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
 
unsecure layer
Proxy layer
Secure layer
 
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
 
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
 
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?

View 1 Replies View Related

Cisco Switching/Routing :: WS-C6509-E High CPU Utilization

Jan 13, 2013

I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.

[Code] .......

View 5 Replies View Related

Cisco Switching/Routing :: C6509-E Do A Unexpected Reload

Feb 26, 2012

Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
 
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.

View 1 Replies View Related

Cisco Switching/Routing :: C6509-E / What Is Mean That Is Packet Capture?

Apr 1, 2013

I operate between c6509-E, what did you flooding? its just packet capture gi1/3 but  i dont know it and is it attack?also same seq no switch gots it?what is problem?

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E Doesn't Remove IPs From ARP

Mar 25, 2012

we have a WS-C6509-E WITH SUP VS-S720-10G, and IOS s72033-advipservicesk9_wan-mz.122-33.SXI5.bin. [code]

From, what we can see, whenever we try to clear arp-cache, it doesn't remove the IPs from the ARP. We've checked a bug in the IOS 12.2(33)SXH4 with the same issue, in version SXI4 is solved, but I have version SXI5, it is supposed to be fixed, from this caveat CSCtf16300, since it says it was fixed on 12.2(33)SXI4, it should be fixed on SXI5, right ?

View 2 Replies View Related

Cisco Switching/Routing :: Minimum Power / Voltage Of Switch 3750

May 20, 2013

I want to know how much minimum power required for swicth catalyst 3750.I want to know cause in my building place, the power in unstable so it make my switch corrupt/damage even i add power consistancy....
 
How much amount power to the ups and ups to switch?

View 5 Replies View Related

Cisco Switching/Routing :: Monitor ICMP Traffic On C6509?

Dec 22, 2011

Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
 
qa-c6509-c(config)#monitor session 1 filter ?  vlan  SPAN filter VLAN
 
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.

View 4 Replies View Related

Cisco Switching/Routing :: C6509 Switch Port Over Subscription

Nov 25, 2012

I have a C6509 with WS-X6548-GE-TX port module. The first port group, 1-8, is showing oversubscription (packets dropping) in the shared buffer. What interface commands can I use to find the specific port causing the buffer overflow?None of the ports is continuously overutilized and none of them in a SPAN destination group.I don't want to move connections without knowing which one is causing the problem. Also I fear that moving the connections may shift the bleeding to another shared port group.

View 2 Replies View Related

Cisco Switching/Routing :: C6509-E And VS-S720-10G Visio Stencils?

Sep 9, 2009

I need those two stencils.I have checked here [URL] but:

- the one for the C6509-E is not there

- the one for the supervisor does not work properly (misaligned anchor points).

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E - Possible To Boot IOS From TFTP Server

Oct 21, 2012

I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509 / VLAN Interface Limit

Jan 2, 2012

I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
 
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
 
and vlan:
 
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
165  test5                                 active    Gi7/14
 
But I can't ping this IP address and show ip route shows:
 
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
  Known via "static", distance 254, metric 0 (connected)
 
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?

View 9 Replies View Related

Cisco Switching/Routing :: What Is Heat Dissipation Of C6509-E Configured

Sep 10, 2009

I am trying to figure out what is heat dissipation of a C6509-E configured as follows:
 
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
 
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
 
1) The power calculator says 13630 BTU/h
 2) Manual calculation says: [code]
 
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?

View 2 Replies View Related

Cisco Switching/Routing :: WS-C6509-E - Verification Of Services And Protocols

Sep 19, 2012

Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on.  This layer 3 switch will be used to connect to servers.
 
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)

[Code]....

View 6 Replies View Related

Cisco Switching/Routing :: C6K Randomly High CPU Usage C6509

Mar 20, 2012

We have two c6509 budled in VSS. I have noticed randomly high usage of CPU, sometimes up to 99% in peaks. I have found that it can be generated by SNMP engine. So I unconfigure all SNMP things. But situation is the same. I would like to know if this state is OK or not. CPU shows are enclosed in file.

View 1 Replies View Related

Cisco Switching/Routing :: WS-C6509-E / VSS Switch Showing Very High CPU Continue?

Aug 8, 2012

We are facing issue of getting very high CPU utilization for the VSS Switch model WS-C6509-E some times approx 100%.Attaching here show tech-support taken later after CPU normal along with show logging, show cpu sorted.HCAINNOI01XXXCS0001#sh proces cpu | ex 0.0%CPU utilization for five seconds: 100%/13%; one minute: 90%; five minutes: 91%PID 5Sec 1Min 5Min Process16406 91.2% 75.2% 76.2% ios-base16426 1.7% 1.4% 1.4% udp.proc16429 0.3% 0.3% 0.3% raw_ip.proc16432 2.8% 3.1% 3.1% cdp2.iosproc

View 3 Replies View Related

Cisco Switching/Routing :: WS-C6509-V-E / Mac-address-table Synchronize Command

Nov 27, 2011

we have  cisco WS-C6509-V-E with IOS version 12.2(33)SXI4; s3223_rp_IPSERVICESK9_WAN_M) running on a switch. I am trying to configure the command "mac-address-table synchronize" under global config mode. But when I enter the command Cisco(config)#mac-address-table ?It doesn't show the synchronize option?

View 3 Replies View Related

Cisco Switching/Routing :: WS C6509 E - DHCP Snooping Command On CatOS

Nov 14, 2012

I am trying to find a command for dhcp snooping rate-limiting on a CatOS. The PFC card is PFC. PFC3B is said to support that command. But there seems no this command.
 
-6k> (enable) sh ver
   
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug  3 2005, 13:26:46
 
[Code] ......
 
Up time is 1183 days, 1 hour, 41 minutes

View 3 Replies View Related

Cisco Switching/Routing :: Requirements For Line Card Upgrade On WS-C6509-E

Jan 14, 2013

We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:

1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
 
What are the requirements in terms of IOS and Roman.
 
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2) 
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
 
Do I need an upgrade?

View 3 Replies View Related

Cisco Switching/Routing :: Possible To1941 Security Bundle Router Support Minimum Of 2k Of VLAN ID

Dec 17, 2012

Is it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?

View 4 Replies View Related

Cisco Switching/Routing :: C6509 Loss Of Packets ICMP Sent By Different Hosts In Different VLAN

Oct 17, 2012

I've a big problem with a loss of packets ICMP sent by different hosts in differents VLAN. Here my architecture:
 
Core Switch : 2 Switch's C6509 (Version 15.0 (1) SY1)- Mode VSS - One lien VSL , the other link is defective.Access Switch: C3750 , Connected to Core Switch through 2 fibre optique wires.Topology: redundant ring
 
When I send consecutive ping message I  found always a missing of packets . Furthermore When I insert the  "show ip traffic" command., the parameter "bad hop count" increase after a loss of packets. I've 2 hosts connected in my network and they send packets with TTL =127.
 
In the Core Switch I haven't configured the MEC because it gave me troubles with the packets multicast.

View 1 Replies View Related

Cisco Switching/Routing :: C6509 - Broadcast Not Working Between Primary And Secondary IP Address

May 11, 2012

I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet    & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine...  Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...

View 6 Replies View Related

Cisco :: WS-C6509-E OID For Virtual Switching System

Nov 21, 2011

The OID I am using  for module index 6509-E family is not working on 6509 Virtual Switching System(VSS).I have used "1.3.6.1.4.1.9.5.1.3.1.1.1" for single6509- E configuration. How to know OID for module index on VSS environment.

View 5 Replies View Related

Cisco Switching/Routing :: 2911 With IOS Version Is 15.1 - Routing Table Not Updating

Oct 2, 2012

I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.

View 2 Replies View Related

Cisco Switching/Routing :: Show Version On VSS 6509?

Apr 7, 2013

Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.

View 3 Replies View Related

Cisco Switching/Routing :: IOS Version For C3500XL Switch?

Nov 13, 2007

im trying to find out what is the latest ios version for 3500xl switch for upgrade it .

View 4 Replies View Related

Cisco Switching/Routing :: 5505 Latest OS Version - 9.0.2 Or 9.1.1?

Apr 23, 2013

On the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?

View 4 Replies View Related

Cisco Switching/Routing :: Upgrading IOS On 2811 From Version 12.2.X To 15

Apr 25, 2012

I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
 
The product number looked like this
CISCO2811-HSEC/K9    2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
 
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?

View 2 Replies View Related

Cisco Switching/Routing :: 4900M - Upgrade IOS Version

May 7, 2012

I have this 4900M running version 12.2(54)SG1.  I the log I get this 3 lines:

May  8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0  aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May  8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry:  Sw entry:
May  8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0  aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
 
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ".  I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved