On the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?
View 4 RepliesI am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?
View 3 Replies View RelatedI upgraded a 2811 router to the latest version and apparently everything went smooth. I reloaded and did a sh ver the IOS show the correct version, but the boot strap shows the old IOS. How can I change the boot strap to show the new IOS.
View 4 Replies View RelatedI have Cisco 6513 with sup720 running s72033-adventerprisek9_wan-mz.122-18.SXF8.bin. I would like to upgrade with the latest and stable IOS.
View 5 Replies View RelatedI have a ASA5505 and currently running Version 7.2(4). I was wondering what the latest version of the software would available to me would be.
Here's a show ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
Compiled on Sun 06-Apr-08 13:39 by builders
System image file is "disk0:/asa724-k8.bin"
Config file at boot was "startup-config"
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?
what is the latest firmware version for d-link dir-825? It tell me that i currently got the 2.60VT, is it the last one? If no, where can i download and how the latest version?
View 14 Replies View RelatedWe are a Small company with 400-Users and currently we are using ACS 4.2 at our company.we want to upgrade and use Cisco ISE Appliance instead.
I want to know is there any major changes in configuration between ACS 4.2 and the ISE Latest Verizon.?
Is there any Hardware (Switch or Cisco AP ) compatibility issues with using Cisco ISE. (we are currently using Cisco Cat 3550 and Cisco Aironet 2600 APs with the existing ACS4.2) What ISE Series & what Soft version are the latest so i can order ?
I am working at a client site today whom has Cisco ACS employed. Their current version is 4.1. It has been some time since I have done any upgrades on this system. What is the most current version for this appliance?
View 5 Replies View RelatedWhere the list of changes for the latest firmware version can be found? My new DIR-655 has firmware from May 2010, and I see the latest and greatest on the DLINK website is from September. But it doesn't state what the changes are, so I'm not sure if I should upgrade or not.
View 8 Replies View RelatedWe just purchased the following items:
(1) R-PI-1.1-500-K9
(2) PRIME-NCS-APL-K9
I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.
I have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.
We are running ACS 4.0 so understandably so we are looking to upgrading to a Cisco supportable version of ACS. The limitation of our current version of ACS does not support nested AD groups. The latest version of ACS (I think it is 5.4) will?
View 1 Replies View RelatedWhat is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0
I see the following at Cisco website:
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
Just purchased a Belkin AC1200 Router Modem and unable to locate the model number what is the current firmware version It is the UK model and I guess it must be very new?
View 4 Replies View RelatedWhen you will release the latest version for Wireless router Linksys E2100L?, because I bought a MAC with Lion and I can´t use my Router.
View 4 Replies View Relatedwhat is latest firmware version is for router WRT 160n (v1). The Linksys site currently states that it is Ver.1.02.11 (11/08/10). However, on the admin page for my actual router it states v1.52.0 Nov 16, 2007. These versions #s and dates don't jive. How could I have a supposedly newer version that is older than the most recent one posted?
View 3 Replies View RelatedAll of a sudden, my GUI look like this I'm using the latest version of Safari on a MacBook and FW 1.0.04 on the E4200.When I click on one of the menu items the only thing I get is "404 File not found".
View 3 Replies View Relatedwhat is the latest firmware for cisco 1841 ? is firmware and router IOS image are same ?
View 1 Replies View RelatedI want to upgrade to the latest IOS for a client of mine. My client has the following image: cat4000-i5k91s-mz.122-25.EWA14.bin
His hardware specifications are as following:
cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory.
Processor board ID FOX102203CC
MPC8245 CPU at 400Mhz, Supervisor V
Last reset from Reload
5 Virtual Ethernet interfaces
152 Gigabit Ethernet interfaces
[Code]...
I have two 3750x stacked switches , both with the latest firmware on them. I enter the configuration onto one switch and it obviously copies over onto the other switch. Although in the configuration I have both a console username and password and an enable password, when I try to log onto the initial switch that I entered the configuration on, I am prompted for a username and password, which works fine, but when I try to enter enable mode i get an error stating that no password has been set. However when logging onto the other switch I am not prompted for a username or password but when I try to enter enable mode I am prompted for a password and can access it with no problems.
View 1 Replies View RelatedI recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
I'm setting up an ASA 5505 with IOS 8.4(2) and ASDM 6.4(5) using the SSL client (well, and the Clientless SSL, but one thing at a time.) This is for a SOHO (they're on a cable modem) such that I should be able to remotely VPN into this system from anywhere on the Internet for support purposes.
I have the certificate generated, I can authenticate via AnyConnect - no errors. I'm used to using NAT exempt commands to move forward, but the ASA is telling me that my commands are invalid (as are the suggestions from the Cisco site, which apply to an earlier version of the ASA's software.) My local LAN access is fine.
I can't ping anything on the only network behind the firewall. (I can ping myself.)If I do a "route print" on my Windows box, it is routing correctly.I've got to be missing something basic, but for the life of me, I can't see it. My network behind the 5505 is 192.168.0.0/24; I have a VPN-Pool of 192.168.101.0/24; [code]
i need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View Related(F5D9230-4 v5111 Belkin mimo router ) is version 5.02.08 the most up to date firmware for my router?
View 1 Replies View RelatedI am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedIs there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 Replies View Relatedim trying to find out what is the latest ios version for 3500xl switch for upgrade it .
View 4 Replies View RelatedI purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
Unforunately I have not been able to find any IOS version requirement for a brand-new 1000BASE-LX10 SFP (MGBLH1) in the internet.
The IOS version in use on this stack is:Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)
[Code]...
I have searched for this error and beside a third-party module (this is a Cisco SFP) the reason could be that newer IOS version is required. Before I'll request an IOS update to the stack with our internal team, IOS version required for this module to run properly and maybe a link to an overview to lookup such requirements in the future.
I need to confirm that the 4510R+E switch with the SUB7-E/2 running version 15 IOS will not support NAT. I am 99% convinced that it does not but i am looking for confirmation, as i am a bit surprised by the lack of NAT support on this platform.
View 0 Replies View Related