I want to upgrade to the latest IOS for a client of mine. My client has the following image: cat4000-i5k91s-mz.122-25.EWA14.bin
His hardware specifications are as following:
cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory.
Processor board ID FOX102203CC
MPC8245 CPU at 400Mhz, Supervisor V
Last reset from Reload
5 Virtual Ethernet interfaces
152 Gigabit Ethernet interfaces
[Code]...
I am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?
View 3 Replies View RelatedI upgraded a 2811 router to the latest version and apparently everything went smooth. I reloaded and did a sh ver the IOS show the correct version, but the boot strap shows the old IOS. How can I change the boot strap to show the new IOS.
View 4 Replies View Relatedi need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedI am planning to upgrade Cisco 4948 IOS upgrade. We have few with older code( 12.2(25)EWA7), when issue sh version shows as Catalyst 4000 L3 Switch Software. while newer version of the switch show as Catalyst 4500 L3 switch.
1 Is this/(sh ver output) just because of the Older code ?
My 2 question is according to release note : [URL]
You need to upgrade your ROMMON before the IOS . 2 What is the approximate time it take to do this ROMMON upgrade ?
what is the latest firmware for cisco 1841 ? is firmware and router IOS image are same ?
View 1 Replies View RelatedOn the downloads page there's a 9.0.2.ED listed as the 'latest' but then if I expand the '9' below it I get to 9.1.1.ED. Which one is the actual latest? is there any way to tell the one that is not an 'interim' version I think 9.1.1 is also listed under interim?
View 4 Replies View RelatedHow to upgrade cisco asa 5510 from 8.0(4) to latest ios. Update latest one and step to upgrade. also need to update IPS firmware also because this device together with IPS.
View 9 Replies View RelatedWe have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedWe just purchased the following items:
(1) R-PI-1.1-500-K9
(2) PRIME-NCS-APL-K9
I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.
I have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.
I have two 3750x stacked switches , both with the latest firmware on them. I enter the configuration onto one switch and it obviously copies over onto the other switch. Although in the configuration I have both a console username and password and an enable password, when I try to log onto the initial switch that I entered the configuration on, I am prompted for a username and password, which works fine, but when I try to enter enable mode i get an error stating that no password has been set. However when logging onto the other switch I am not prompted for a username or password but when I try to enter enable mode I am prompted for a password and can access it with no problems.
View 1 Replies View RelatedI have Cisco 6513 with sup720 running s72033-adventerprisek9_wan-mz.122-18.SXF8.bin. I would like to upgrade with the latest and stable IOS.
View 5 Replies View RelatedI recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
I have a DCS-942L. Everything was working fine on my setup until I upgraded the firmware the other day. In the mydlink.com website when I logged in that day, it stated a firmware upgraded was needed. So I clicked on upgrade, let it run its thing and then tried to view the playback and now the thumbnails are just black and when I click on one, it looks like it is loading but then shows the quicktime icon with a question mark over it. I upgraded my Quicktime component and that didn't fix it either. So I went into advanced settings, downloaded the new firmware upgrade from there by saving the zip file and uploading it via the advanced settings website, and still nothing. I have another camera, same setup, that I have not upgraded firmware on yet and that playback is working fine.
View 1 Replies View RelatedRegion : Denmark
Model : TL-WDR4300
Hardware Versin : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
my TP-Link USB Controller after my latest firmware upgrade, and therefor my USB-printer (connected to the router) do not function any more, and i can not find a new software for the Controller
Have a new 4500-x (Comes with IPBase enabled), but I see only universal image is available for download (Which I understand has "all" features)...assume it is safe to use the latest universal image on 4500-x and the IPBase license will be automatically applied?
I also see there is a new rom upgrade available - Is this the correct procedure to follow: [URL]
Should I be doing the rom upgrade first?
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies View RelatedDoes the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies View Relatedquestion on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies View RelatedWhy Cisco 4500 R switch PBR tracking Command not working , I found just route-map next-hop ?
View 3 Replies View RelatedMy 4500 core always in 60 % cpu utility , and when i run #sh proc cpu sorted i find that
55 29725041543795572214 0 39.43% 41.40% 41.39% 0 Cat4k Mgmt LoPri
Which mean that this process is the top one , and when i run #sh platform health i found that Stub-JobEventSchedul
10.00 15.98 10 64 100 500 20 17 12 29269:55 K2 CpuMan Review
30.00 35.60 30 48 100 500 49 46 32 52390:52
Those two process are the top and they already exceed their maximum rang and when i run #sh platform cpu packet statistics i can find that Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Esmp 5053121950 475 462 340 326
L2/L3Control 244395185 17 8 5 11
Host Learning 67315739 0 0 0 0
L3 Fwd Low 346689615 73 23 14 13
L2 Fwd Low 5336180603 1180 1129 831 804
L3 Rx Low 2287913 0 0 0 0
RPF Failure 7510829 1 0 0 0
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies View RelatedI am getting a very strange problem where 4500 switch is remarking the packet with dscp 1 to 0.
Let me explaint the setup. I have two PCs connected on same switch but on different modules. PC1 is conencted to Gi4/19 and PC2 is connected to
Gi2/43. Both the ports has been configured to trust the dscp. Below are the configuration:
interface GigabitEthernet4/19
switchport access vlan 6
switchport mode access
[Code].....
I am trying to setup the WOL for our enterprise. We have a C4500 setup with mutliple Vlans. We are using Microsoft SCCM server to wake up workstations for security update. The workstations are on vlan190 and the Microsoft server is on vlan 441
Here's my config
the config below
interface Vlan190ip directed-broadcast 100 (Enables the translation of a directed broadcast to physical broadcasts)
access-list 100 remark ====== Wake-On-LAN ======no access-list 100 permit udp host 10.4.40.98 any eq 9 logaccess-list 100 remark ====== End of ACL 100 ======
[Code].....
We have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below
### For 4500 Switch
class-map match-all VOIP-Access-2MB
match cos 3 5
class-map match-all VOIP-Uplink-20MB
match cos 3 5
[code].....
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?
read the posts regarding vlans that are administratively down, they suggested that they are down if no ports are assigned to them, however I do have a switchport assigned, and the interface is still down. This is on the vtp server and on the clients. The vlan is not listed when issuing show vlan brief. Other vlans configured in a similar way do show and their interfaces are up. These are two Catalyst 4948-10G.Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).
View 5 Replies View RelatedI have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.
View 1 Replies View RelatedWhen I connect two 4500-x switches in a VSS setup, do I need to have both 4500-x switches equiped with Enterprise Services, or can I mix IP Base with Enterprise Services in one VSS setup in order to save on licensing costs?
View 1 Replies View RelatedI have a Cisco 4500 Sup 6 engine and I have two 48 port fiber line cards installed. When I do a show interfaces I do not see any of the Fiber cards. This is a new out of the box 4500 and I installed the Sup 6 Line card in Slot #1, And the two 48 port Fiber cards in Slots 2 and 3. Am I missing something, is there a command or set up procidure for the line cards. I just assumed they were plug and play
View 2 Replies View Related