I have a Cisco 4500 Sup 6 engine and I have two 48 port fiber line cards installed. When I do a show interfaces I do not see any of the Fiber cards. This is a new out of the box 4500 and I installed the Sup 6 Line card in Slot #1, And the two 48 port Fiber cards in Slots 2 and 3. Am I missing something, is there a command or set up procidure for the line cards. I just assumed they were plug and play
View 2 RepliesI wonder are 4500-E series line cards (i.e. WS-X4648-GB-RJ45, WS-X4748-UPOE+E and WS-X4606-X2-E) supported on 4507R chassis? Datasheet says "Classic line cards may be deployed in both classic and E-Series chassis with either classic Cisco Catalyst 4500 Series supervisor engines or with the Cisco Catalyst 4500E Series Supervisor Engine." But it says nothing about E-Series line-cards being (or not) supported on classic chassis (like 4507R).
View 3 Replies View RelatedI have 2 x WS-X4548-GB-RJ45 Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45) line cards in a 4500 chassis with 2 x WS-C4507R-E E-Series Super visor engines. We would like to create a layer 3 ether channel from a access layer switch terminating on our 4500 chassis. Can we configure the ether channel from the access layer switch such that one port on the ether channel is on one line card and the other one is on the other line card?
View 2 Replies View RelatedI have two data centres connected via a L2 DWDM, my manager wants to look into using OTV to get rid of the layer 2 broadcasting issues.
Problem is the DWDM is 1000BaseSX, which is only supported on the N7K-F132XP-15. (and the N7K-M148GS-11 but that doesn't support FCOE, so many bloody caveats). From what I can gather OTV is not supported on the N7K-F132XP-15.
Is it possible to terminate the DWDM on the F1 card & loop another port from the F1 to a port on the N7K-M148GT-11 & run OTV on the M1????
Either using VDCs or just an isolated VLAN on the F1. Is there any better way to do this? Hardware has not yet been purchased.
We need to move some line cards around on our 4510. The top slots have a 24Gbps backplane while the lower slots are limited to 6Gbps. Poor planning on our part has left us with installing a 10Gb line card in one of the bottom slots. I'd like to move a couple of the cards up top, to the bottom.
My question is simply will the switch magically preserve the configuration for those cards and change the slot number for me or will I need to reconfigure the interfaces for those cards I move?
I have a requirement to upgrade some line cards in our 4510R-E chassis to ease some oversubscription due to the 6Gbps limit.
At the moment my plan is to upgrade three cards from WS-X4548-GB-RJ45 to X4648 to get the 24Gbps per card.
Supervisors are 6-E
1. Is this a viable plan?
2. If so can the cards be hot-swapped?
3. Would the new cards retain the existing interface settings of the previous cards?
4. Any gotchas to look out for?
I would like to know whether WOL is supported on a N7K with 6.x code and F2 line cards. I also would like a how to for this. If it is not supported will an ip helper address to the broadcast address of the destination vlan SVI will suffice to get it workinng. If so I can restricht the forwarded broadcast to only the wol traffic.
View 1 Replies View RelatedI read the document, [URL]
[
Q.I have Cisco 6700 Series line cards today with Centralized Forwarding Cards (CFCs). Are these line cards supported in a Cisco Supervisor Engine 2T system?
#
A. A Cisco Supervisor Engine 2T system will support all Cisco 6700 Series line cards with CFCs.
]
So, As long as the 67XX line card is using CFC, it is compatible with Sup-2T.
I also find the IOS release note indicate the 6704-10G with CFC is supported by Sup-2T, but it require 512M memory.
[URL]
The bug details is not disclosed. So I further search what the default memory size of the WS-F6700-CFC is, then I found here says it is only supported by Sup720 and no memory upgrade option, which means must upgrade to DFC4, in another words, it is not compatible with Sup-2T
[URL]
WS-F6700-CFC:
Centralized Forwarding Card (CFC) for use on WS-X67xx Ethernet modules. This daughter card is supported only by the Supervisor Engine 720. There are no memory options for this daughter card. default memory: 256M
So my question is: whether “WS-X6724-SFP with CFC” and “WS-X6704-10G with CFC” compatible with Sup-2T without upgrading to DFC4 daughter card, and do they support in VSS-2T?
Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
I wanted to know that in nexus 7009, can i use mix of F2/M1/M2 series line cards ? will they work with each other ? Lets say i have F2 line card and M2 line card, will servers attached to them will communicate with each other ?
View 4 Replies View RelatedWhen quoting a WS-X6724-SFP line card for a Catalyst 6500:
1. If no Distributed Forwarding Card 3 (DFC3) is selected, can it be purchased at a later time as a spare part or the client needs to buy the line card with the DFC3 included from start?
2. Does each line card require a DFC3 in order to be able to perform localized forwarding decisions?
3. Does the DFC3 card is embedded in the line card physically?
Client has Cisco 4507R+E chasis with SUP- 7L-E and he has WS-X4418-GB line card in stock can this line card work with E series chassis
View 2 Replies View RelatedI need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies View RelatedI recently changed the entire configuration on two 6509 switches, and the fibre modules on slot 7 and 8 have gone down on BOTH switches. It would be easy to say that its a hardware fault but I cannot understand how module 7 and 8 can go down on both switches. Initially I thought it maybe due to IOS bug 22-33.SXI2a.bin" so I upgraded it to s72033-advipservicesk9_wan-mz.122-18.SXF12a.bin but it still down.These are the actions I have carrried out to try resolve the issue:
- Reverted back to orginal configs but no luck
- Tried to use "power enable" command but the status light on both modules seems to turn red and then go off again.
- I have also tried to put one of the fibre modules into a different slot but no joy
- Upgraded the IOS from 22-33.SXI2a. to 122-18.SXF12a
I am sure that hardware fault cannot occur on BOTH modules 7 & 8 on BOTH switches after config change.The error in the log shows that modules "failed to bring online because of registration timer event". I understand this means that it is unable to download the image within the allocated time. [code]
I previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
It is possible to add interface from different line cards reference ( for example N7K-148GT-11L and N7K-F132XP-15 ) to a vPC ? I ask you because I try it and I have the following error :
command failed: port not compatible [Capabilities FabricPath]
I have a number of existing 4506 chassis type switches (the older non -E version) that I would like to roll out IP phones to. Instead of replacing the entire chassis, I would like to just replace the line cards in the switches with WS-X4548-GB-RJ45V. What or how much power supplies should I have in each switch to be able to power the 5 poe line cards (each port per line card will power an ip phone)?
View 6 Replies View Relatedwe need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies View RelatedI have a console access to a Cisco 4500 series router over Cisco access server, which has following "line con 0" configuration:
View 8 Replies View RelatedI configured dot1x on my swicth 4500 series, Here is the interface configration:
interface FastEthernet3/2
description Test dot1x
switchport mode access
load-interval 30
authentication event fail action authorize vlan 800
authentication host-mode multi-host
authentication port-control auto
[code]....
When I remove the port-control configuration on the interface, the status change to UP/UP.
I want to add a new phone line to a small office in a hotel. They have avaya phone system and they are currently using 6 or 7 phone lines. From the avaya wires are run to the 66 block and from there to the outlets. So i think i can connect a cable from the avaya to the 66 block and it automaticaly give an extension number, but how do i add a phone line number to that connection?
View 5 Replies View RelatedWe have the Cisco Cat4510 with the 2 Sup-6Es as follows:
5 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
6 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
Each line card comes with dual 10Gig Ethernet X2 Optics. I am currently using int g5/1 and g6/2. I tried to connected a server to the int g5/2 and assigned the poper parameters(VLAN, speed, ...etc) but I am the int is showing down. Is there some type of limitations in using the second port of each line card?
I know there are some line cards on the 6500 that do not play well with each other when trying to setup an etherchannel using two different line cards on the same chassis. I always thought it was line cards of different type, i.e. 6400 with a 6700 but these two line cards are exactly the same model with the same code level.
1) Are the error messages below from this incompatibility between line cards and etherchannel creation?
2) How to fix if the answer to #1 is yes?
3) What line cards work with which for etherchannel creation?
Assuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies View RelatedDoes the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies View Relatedquestion on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies View RelatedWhy Cisco 4500 R switch PBR tracking Command not working , I found just route-map next-hop ?
View 3 Replies View RelatedMy 4500 core always in 60 % cpu utility , and when i run #sh proc cpu sorted i find that
55 29725041543795572214 0 39.43% 41.40% 41.39% 0 Cat4k Mgmt LoPri
Which mean that this process is the top one , and when i run #sh platform health i found that Stub-JobEventSchedul
10.00 15.98 10 64 100 500 20 17 12 29269:55 K2 CpuMan Review
30.00 35.60 30 48 100 500 49 46 32 52390:52
Those two process are the top and they already exceed their maximum rang and when i run #sh platform cpu packet statistics i can find that Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Esmp 5053121950 475 462 340 326
L2/L3Control 244395185 17 8 5 11
Host Learning 67315739 0 0 0 0
L3 Fwd Low 346689615 73 23 14 13
L2 Fwd Low 5336180603 1180 1129 831 804
L3 Rx Low 2287913 0 0 0 0
RPF Failure 7510829 1 0 0 0
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies View Related