Cisco Switching/Routing :: Upgrading IOS On 2811 From Version 12.2.X To 15
Apr 25, 2012
I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
View 2 Replies
ADVERTISEMENT
Dec 8, 2011
I want to know is there is an license for upgrading the C2960-48PST-S to the "L" version (Lan Base).
View 2 Replies
View Related
Aug 22, 2012
I upgraded a 2811 router to the latest version and apparently everything went smooth. I reloaded and did a sh ver the IOS show the correct version, but the boot strap shows the old IOS. How can I change the boot strap to show the new IOS.
View 4 Replies
View Related
Mar 13, 2012
We are looking to upgrade our WiSMs to version 7.0.230.0, but the Cisco compatibility matrix suggests we need to upgrade WCS to the same version (it is currently on 7.0.172.0). My question is can we upgrade the WiSMs and do the WCS at a later date with no issues or do we need to do them at the same time to keep visibility of everything?
The reason I ask is that some of my clients use lobby ambassador for some of their users and they will need wireless access on the day we are due to upgrade WCS (the WiSMs are due to be upgraded and rebooted earlier that morning.
View 1 Replies
View Related
Apr 26, 2012
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?
View 3 Replies
View Related
Oct 13, 2011
I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220.When it was unstable, I found three strange condition 1. A lot of log looks like this*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/1059/stat.(erno 24)*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'fmcHsTask'2. Internal Temperature was showed "sensor failed"3. CPU User load is Zero?
View 8 Replies
View Related
Mar 9, 2013
I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220. [code]
View 1 Replies
View Related
Mar 28, 2011
Did anybody ever succeeded upgrading 1.3.12.19-tm to 4.0.0.07-tm version?
View 1 Replies
View Related
Apr 11, 2012
The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
View 13 Replies
View Related
Sep 7, 2009
I would like to ask if a cisco 2811 running on an ios c2800nm-adventerprisek9-mz.124-25a.bin should be able to make an HWIC-1FE card work? I am also not detecting the card on any show commands. Plus i am seeing that all the LEDs (FDX/COL,100 and LINK/ACT) are lit steadily even though there is no cable attached to it, is it safe to say that the card could be defective?
View 6 Replies
View Related
Jul 31, 2012
I'm trying to run ZBFW on a 2811 with IOS version 15.3(T4) and I'm running into a strange issue I'm not quite sure how to troubleshoot.
I have 3 zones, internet, local, and ssl-vpn.The rules I'm trying to enforce are: all traffic from SSL-VPN can go to anywhere, anywhere can go to SSL-VPN. Anything originating from local can go out. Certain ports can come in for DMZ services (http, https, imap/s, pop3/s, submission).
After rebooting the router and applying f0/0 and tun0 to internet, f0/1 to local, and virtual-template 1 to ssl-vpn things work fine. But after a while I stop being able to connect to servers at the high end of the subnet. (I have .20 to .26 configured with the services, .20, .21 work fine always, .22 and up stop responding). Remove interfaces from the ZBFW, no problem at all. Apply ZBFW, traffic stops.
I'm seeing dropped sessions in the log on zone-pair local-to-internet , invalid flags with ip ident 0 which I think is outbound traffic attempted for no inbound inspect entry, but everything should be allowed out, and the traffic is to port 80 which is allowed by 'match protocol http' on the inbound policy.
Edited config attached (remove passwords and stuff) Last few log lines are at the bottom.
View 3 Replies
View Related
Jan 31, 2013
I am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
View 2 Replies
View Related
Jan 15, 2011
We want to upgrade the IOS from 15.0(1) to 15.1 for some reason. Here is the output of my router's "show ver":
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 18:32 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE
[code]....
We have enabled the technology package license "uc" in the previous version, would it be loss after the upgrade?
View 5 Replies
View Related
Jan 4, 2013
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies
View Related
Aug 30, 2012
we have two core swiches 6506 and around 55 cat 3550 switches. currently we are on the process of replacing the cat 3550 switches to 3750 switches.We need 10/1000/1000 speed, ip base image with upgrade options. Our up links from cat 3550s(sfps) are single mode and dual mode fiber mode with 1 gbps ports on core switch.
At present we are not upgrading to 10 gb modules on core. Spread over 15 floors each floor needs 2 up links(single mode , and dual mode). since cat 3750 sfps are smaller in size existing gibics cannot be used. Looking for the best option of cat 3750 switches with 1 gb up links which can be upgraded to 10 gb later when we replace the modle on core. Requirements:
1- Cat 3750 switches 55 in no with sfps for 1 gb up link (dual mode fiber and single mode fiber)
2- stacking option
3- 10/100/1000 speed
4- ip base image upgradable to ip service image
5- ipv6 compatibaility. Network is spread over 15 floors so from each floor we need two sfp up links 1 gbps using dual mode and single mode
-6-Should be upgradable to 10 gb in future when we upgrade the core modules
Or is it better to go for 10 gb module in core as well as edge switches ? if so what should be the modules?
View 13 Replies
View Related
Jun 4, 2012
I am planning to upgrade my cat6500 using ISSU but can not find my doc to follow yet.
View 1 Replies
View Related
Apr 18, 2013
I am upgrading a Cisco 6506E VSS from 12.2(33)SXI5 to 12.2(33)SXJ5 during a maintenance window. So I have plenty of time to reboot the VSS. Confirm below is the correct procedure. I have manually copied the new IOS to both active and standby Sup720s.
no boot system
boot system flash sup-bootdisk:NEW_IOS.bin
boot system flash sup-bootdisk:OLD_IOS.bin
!
copy run start
reload
I was going through the below cisco document and there are a few more steps as below: Is it necessary?
[URL]
Router(config)# no boot system
View 2 Replies
View Related
Mar 19, 2013
I am looking at upgrading my 6503-E switch. While I get the chance, I would like all aspects upgraded as I finally have some "downtime". I am running a Sup 720-3B.From what I understand, the boot image is a recovery image (mini IOS) - should the main IOS fail.Where should this be installed, sup-bootflash:/ or bootflash:/ ?,The file is “s72033-boot-mz.122-33.SXI11.bin.”The Boot Loader. My understanding is that Bootloaders are not used in these Sups with a MSFC3? I am not sure why TBH .. but would this be the case ?Rommon can be upgraded. I don’t quite understand if there are two ROMs (SP and RP).
View 1 Replies
View Related
Apr 29, 2012
I just need a little refreshing on upgrading a stack of 3750's. This stack only has 2 switches: [code]
1.) If I remember correctly I simply tftp the IOS to the flash of each switch and then reload the master only?
2.) Can I safely assume these are the 2 flash locations:
View 3 Replies
View Related
Apr 2, 2012
I had a strange problem here after upgrading Cisco 3750X.The upgrading was going smoothly, I copied a newer IOS to the flash from another Cisco 3750X through TFTP, changed the boot image.It took a while do to the microcode upgrading, finally, it started to boot up. But when it completes the boot up, I can't see the normal login prompt, but only some strange codes. From what I can see, it seems some decoding problem, as if I plug or unplug a cable from the switch, the strange code pops up again, like in normal situation, the console tells you that the interface is going up and down.
The original image of the switch: c3750e-universalk9-mz.122-53.SE2.bin
Upgrade to image: c3750e-universalk9-mz.122-55.SE3.bin
However, I don't have any problem to telnet to this switch, as it has correct IP address and login configured before the upgrading. I have reboot the switch for couple of times, reconnect to the serial port still doesn't show me anything.I am wonering has any one has met this situation before? detailed message shown after the boot up. cisco WS-C3750X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1449Z04L
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
[Code] .....
View 3 Replies
View Related
Feb 20, 2012
I have a 4510R-E chassis which currently has a single supervisor 5 installed.
We are now looking at upgrading the supervisor to a Sup6. Now the question is this, can I install the Sup6 into the redundant cpu slot and then perform a failover to get the new switch working without any noticable downtime.
I'm not sure what having a Sup V and a Sup 6 in at the same time will do to the backplane.
Otherwise I have to take the switch down and then install the card and software manually.
View 2 Replies
View Related
Oct 12, 2012
It would be so easy but failed to upgrade 3560X switch to ip services licence is bought and paid for mail and log from the CLI and tftp server attached
View 17 Replies
View Related
Dec 3, 2012
way to upgrade the IOS in my stack on 4 3750x switches
View 6 Replies
View Related
Jan 16, 2013
Am attempting to load a new license on a 24 Port 3750X. Was LANBase code, need to get it to IPBase. Have the license file. Have put it on the flash drive. Running "license install flash:" i get the message "%Error reading flash: (is a directory)%Error: License installation failed with error: XML parsing failed"The license installation instructions are a bit cryptic so I could be messing it up. However, every variation I can think of is not working. The command listed above gets the most "promising" results.
View 1 Replies
View Related
Dec 28, 2012
It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies
View Related
Feb 17, 2012
I have the following switch:
#show version
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Image text-base: 0x01000000, data-base: 0x02C00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
[code]...
I have downloaded c3750-ipservicesk9-mz.150-1.SE2.bin and I want to upgrade iOS to this image.
I have a few questions related to this:
1. Is my switch model compatible with this iOS version?
2. Do you recommend the upgrade? Does it bring some notable features?
3. Can I upgrade for free or do I need to buy some license?
4. I also want to upgrade/add the crypto image, can I add crypto for free or some license is required?
5. I have remote access to my switch via the console cable which plugged into machine1. But machine1 is connected to network via the same switch. I am accessing machine1 via SSH, and then the switch via console cable (minicom on CentOS). Is there an upgrade procedure for this kind of situation that also has some fall back (like reboot in X minutes and load the previous image) if the upgrade goes wrong?
View 6 Replies
View Related
Jan 10, 2012
I have a customer who has a Cisco 2821 router with software 2821/HSEC/K9 and they wish to upgrade to C2821-VSEC-SRST/K9.From my understanding they want to use the same router but install an IOS with the capabilites it has at the moment but with voice. [code]How do I go about pricing this up and what upgrade sku's will do this?I am not to worried about the memory.Is it just a simple ios upgrade as the srst licenses are on a trust basis?
View 2 Replies
View Related
Nov 3, 2011
I have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
View 5 Replies
View Related
Nov 9, 2011
I have cisco 3750 with ipservices license and I am running with c3750e-universal-mz.122-50.SE2. And I would like to upgrade the IOS " k9" IOS. ie c3750e-universalk9-mz.122-50.SE2. Is there any license required for that ?Also any difference in the IOS upgrade procedure.
View 1 Replies
View Related
May 19, 2013
I currently have a 3560G switch running c3560-ipservicesk9-mz.122-58.SE2 I have a spare 3560 V2 switch I want to configure and have ready in case of a failure. This spare switch is running c3560-ipbasek9-mz.122-55.SE5 My plan was to pull the IOS image from the current switch and upload it to the spare that way I have an "idnetical" switch. From what I have read, there are some feature differences between "ipbase" and "ipservices". However, when I run the show license command on the production switch, I get an unrecongnized command error. So that throws into my confusion as if its running an ipservices image, shouldn't it have a license file?
View 4 Replies
View Related
Nov 9, 2011
I'm having some problems when upgrading the IOS of my Catalyst 3750 switch through a tftp server. I've been surfing the net and found that there seems to be a problem when the image file is larger than 16M but this is not my case.I erased the flash to be sure that there was enough memory space to upload the image but didnt work.I also tried with archive download-sw /overwrite command and using a ftp server but the problem is the always the same: [code]To make sure it was not a problem of my computer or tftp server, I tried with a different computer and with a different tftp server but the same happen. I also tried with a 3750V2 and still the same. Even when trying to backup the current IOS to my computer, I got "error writing".
Then, I have tried to do the same with a different model of switch, a WS-C3560-48PS and it works perfect.I still need to try using Xmodem but Xmodem takes ages to finalize the process.
View 8 Replies
View Related
Apr 4, 2013
I have a Catalyst 4510 that is running IOS version 15.X that has a bug and Cisco recommends upgrading the IOS. Are there additional steps required to perform an IOS upgrade due to licencing Cisco put in place?
View 5 Replies
View Related
Feb 4, 2013
I have a requirement to upgrade some line cards in our 4510R-E chassis to ease some oversubscription due to the 6Gbps limit.
At the moment my plan is to upgrade three cards from WS-X4548-GB-RJ45 to X4648 to get the 24Gbps per card.
Supervisors are 6-E
1. Is this a viable plan?
2. If so can the cards be hot-swapped?
3. Would the new cards retain the existing interface settings of the previous cards?
4. Any gotchas to look out for?
View 4 Replies
View Related
