Cisco Wireless :: WS-6504E / WiSM Can't Function Normally After Upgrading From Version 6.0.182
Oct 13, 2011
I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220.When it was unstable, I found three strange condition 1. A lot of log looks like this*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/1059/stat.(erno 24)*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'fmcHsTask'2. Internal Temperature was showed "sensor failed"3. CPU User load is Zero?
View 8 Replies
ADVERTISEMENT
Mar 9, 2013
I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220. [code]
View 1 Replies
View Related
Jun 19, 2009
although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
View 4 Replies
View Related
Mar 13, 2012
We are looking to upgrade our WiSMs to version 7.0.230.0, but the Cisco compatibility matrix suggests we need to upgrade WCS to the same version (it is currently on 7.0.172.0). My question is can we upgrade the WiSMs and do the WCS at a later date with no issues or do we need to do them at the same time to keep visibility of everything?
The reason I ask is that some of my clients use lobby ambassador for some of their users and they will need wireless access on the day we are due to upgrade WCS (the WiSMs are due to be upgraded and rebooted earlier that morning.
View 1 Replies
View Related
Apr 26, 2012
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?
View 3 Replies
View Related
Apr 25, 2012
I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
View 2 Replies
View Related
Mar 28, 2011
Did anybody ever succeeded upgrading 1.3.12.19-tm to 4.0.0.07-tm version?
View 1 Replies
View Related
Dec 8, 2011
I want to know is there is an license for upgrading the C2960-48PST-S to the "L" version (Lan Base).
View 2 Replies
View Related
Sep 14, 2009
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies
View Related
Mar 11, 2013
which version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies
View Related
Feb 5, 2013
We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?
View 5 Replies
View Related
Dec 19, 2011
I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]
View 21 Replies
View Related
Apr 9, 2012
we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?
View 4 Replies
View Related
Mar 5, 2013
We have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.
However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.
View 7 Replies
View Related
Jun 20, 2012
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
View 4 Replies
View Related
Sep 19, 2012
WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
Eg. VLAN1 - mask 255.255.255.248
VLAN2 - mask 255.255.255.120
Would these two VLANs be able to work together in interface grouping?
View 1 Replies
View Related
Mar 20, 2012
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP.The pertinent config is as follows.
!
vlan 300
name WiSM_Service_Vlan
!interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
[code]....
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to it by doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
View 5 Replies
View Related
Feb 10, 2013
What this card is and what is it used for?
from show module command, it appears that it is a sub-module of the wism blade.
what is it's primary function?
View 1 Replies
View Related
May 4, 2013
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies
View Related
Jan 26, 2013
I am getting an alarm on WCS where a one controller is down, unreachable from WCS, while the other one is reachable on the same WiSM module. Upon investigation, Status of controller is shown as "Oper-Up" for all controllers on Supervisory engine. Hardware platform is Cisco 6509-E.
WLAN
Slot Controller Service IP Management IP SW Version Status
----+-----------+----------------+----------------+-----------+---------------
2 1 192.167.10.11 172.19.47.65 6.0.196.0 Oper-Up
2 2 192.167.10.12 172.19.47.66 6.0.196.0 Oper-Up
However, I can not ping the managment interface of the down controller while the other controller management interface is pingable. All these interfaces are in the same VLAN.
ping 172.19.47.65
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.19.47.65, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Problem is fixed when I reboot the problematic Controller. However, this problem re-appears after some time. I am not able to figure out why controller is not able to ping its default-gateway which is an SVI interface on Supervisory card on the same chassis, and showing status UP/UP. Is it a software bug or backplane fault or any other reason ?
View 1 Replies
View Related
Apr 7, 2013
We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 is not compatible with Po407 and will be suspended (trunk mode of Gi4/1 is dynamic, Po407 is trunk)
View 13 Replies
View Related
Apr 9, 2012
The Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scanning. The phone can work at the Autonoumous mode or other 3rd party Fat AP.
View 1 Replies
View Related
Nov 16, 2012
Setting up a multi floor WLAN using a 6500 WISM Controller. Each floor has an AP group with the floor WAPs assigned. Each floor has a VLAN and the WLC has an interface configured. Each floor has a WLAN configured with the same SSID and the only change is the interface on the WLAN per floor.DHCP is remote on AD servers and each floor as a scope configured.Each floor works fine - we can get connected and get assigned to correct IP address. The issue we had with this setup was moving between floors. When we move up a floor the client loses connection to the inital floor (coverage - as expected). if we disconnect and reconnect it connects to the new floor SSID and gets an IP from DHCP.When looking into this - I then created an interface group and added all the floor interfaces into the group. I then applied the interface group to each floor WLAN and did soem testing - it worked as expected. I could now move between floors.The issue with this is though. When I was testing I already had an IP address assigned from DHCP - before I changed to interface groups. The issue is that the intial DHCP assignment no longer works and we cant connect to the WLAN anymore,
View 2 Replies
View Related
Feb 15, 2012
I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies
View Related
Dec 5, 2011
I have a customer buys 12 x WISM and build up a mobility, when I add the final WLC to mobility, it prompts that there mobility group has reached the max of mobility member, but the total member is 23, according the configuration guide, it should be allow to 24 member, do I hit some bug? My using version is 7.0.98.0.
View 5 Replies
View Related
Mar 7, 2012
I have been having some issues trying to stand up an older WiSM that has been incorrectly configured by my predecesssor and has a bad Mgt IP so I am unable to telnet or SSH into it, nor can I console or session into it.
What I would like to do is to change the Mgt address for the WiSM controllers (1 and 2) by way of the Sup (not sure that is possible) because as it stands they are set to 169.254.1.1 and are unreachable even when directly consoled into them.
Core-A#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.2/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.3 169.254.1.1 4.0.217.0 Oper-Up
3 2 10.104.52.4 169.254.1.1 4.0.217.0 Oper-Up
Core-B#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.50 10.104.30.254 7.0.116.0 Oper-Up
3 2 10.104.52.51 10.104.30.250 7.0.116.0 Oper-Up
I hope to get this WiSM setup on Core A and get it configured like I have my Core B and then run them in a dual failover design with load balancing between the two.
View 6 Replies
View Related
Aug 15, 2012
The problem is WiSM module not coming in OPER-UP status , it’s in Started-Keepalive status.I did run debug wism events on cat6509 and seeing below logs:
[code]...
It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.
View 4 Replies
View Related
Oct 6, 2012
how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?
View 1 Replies
View Related
Sep 22, 2012
I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
View 1 Replies
View Related
Sep 4, 2011
i have a router in my sons room. It is separate from my house. My signal is weak and I can't use my printer with its wireless fucntion. should i buy another router or a repeater
View 1 Replies
View Related
Mar 7, 2011
I have a WRT160N and a WAP4410N but can not get WAP function as a repeater. I have already put as Wireless Client / Repeater and Wireless WDS Repeater. I notice they are both with the same settings security. View attach file.
View 14 Replies
View Related
Sep 2, 2012
We have got 3 Cisco APs 541N with firmware version 9.2.2 and want to set up the cluster function for those APs.Here is the problem:Before enabling the cluster you can ping all three APs located in the same local network with a delay of 1ms or below.If the cluster is enabled the pings for one AP rise above 200 ms in a random way (see attached file).Moreover users connected to that AP are more likely to lose the connection or experience delay.Do the APs communicate through LAN or WLAN ?
View 3 Replies
View Related
Mar 24, 2011
i have internet srevice working with my wireless usb stick or ethernet wire from my gateway modum. in device maneger i have network adapters listed and a question mark before network controller. windows auto update lists no driver avalible for it, and i would like to know it function/purpose?
View 1 Replies
View Related
