Cisco Wireless :: 6500 AP Registration On WiSM

Mar 5, 2013

We have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
 
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.

However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.

View 7 Replies


ADVERTISEMENT

Cisco Wireless :: Can't Console To WISM In 6500

Dec 19, 2011

I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]

View 21 Replies View Related

Cisco Wireless :: 6500 WISM / Layer 3 Roaming And DHCP?

Nov 16, 2012

Setting up a multi floor WLAN using a 6500 WISM Controller. Each floor has an AP group with the floor WAPs assigned. Each floor has a VLAN and the WLC has an interface configured. Each floor has a WLAN configured with the same SSID and the only change is the interface on the WLAN per floor.DHCP is remote on AD servers and each floor as a scope configured.Each floor works fine - we can get connected and get assigned to correct IP address. The issue we had with this setup was moving between floors. When we move up a floor the client loses connection to the inital floor (coverage - as expected). if we disconnect and reconnect it connects to the new floor SSID and gets an IP from DHCP.When looking into this - I then created an interface group and added all the floor interfaces into the group. I then applied the interface group to each floor WLAN and did soem testing - it worked as expected. I could now move between floors.The issue with this is though. When I was testing I already had an IP address assigned from DHCP - before I changed to interface groups. The issue is that the intial DHCP assignment no longer works and we cant connect to the WLAN anymore,

View 2 Replies View Related

Cisco :: 6500 - New WLans Not Broadcasting From WISM To APs

Aug 2, 2012

There are 8 existing W LAN's in our WISM controller & it is working fine without any problem. Now the problem is any new W LAN's are not broadcasting from WISM to APs, I am able to create & enable it in WLC but it these W LAN's are not reflecting in associated APs.
 
FYI: WISM controller is in 6500 switch & FWSM module also in the same switch, earlier there was rule with any any traffic in the FWSM but recently we have removed the FWSM & all rules moved to checkpoint. We have check the in firewall there is traffic is blocking.

View 18 Replies View Related

Cisco Wireless :: AP3502 Registration Failure On WLC 5508

Oct 11, 2011

I am having issues registering Cisco 3502 APs with a WLC 5508. They initially register and then disassociate with the controller and fail to re-register. Is it possible to telnet to AP and factory rest the AP. I get connection refused when I try

View 1 Replies View Related

Cisco Wireless :: 2504 - 1042 AP Registration With Controller

Jul 21, 2012

I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
 
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16 
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...

View 4 Replies View Related

Cisco Wireless :: 1552E / 5508 - Registration Process (AAA Authentication Error)

Dec 9, 2012

i have a problem with 1552E to register with 5508 WLC, and always got "AAA authentication error” in the WLC log, while AAA is not enabled.  so my question is , do i need to add the MAC address to the WLC MAC filter list even if i not enable the AAA server in the WLC.

View 9 Replies View Related

Cisco :: 1230 / 1240 / 1250 - Web Based Registration For Guest Wireless Access

Mar 6, 2011

I just started a project to make a guest wireless network available at every site in my enterprise.  Guest wireless networks are currently available at some sites.  Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution.  All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points.  What do I need to do/get in order to make this happen?

View 3 Replies View Related

Cisco :: LMS 3.2 Application Registration Fail

Mar 12, 2012

I am attempting to register QPM 4.1.5 into LMS 3.2.1 Portal, under Home Page Admin - Application Registration but It fails.It seems to be a bug where it puts the details in the wrong place when submitting the info.
 
This is the output that it tries to submit obviously - Description, host name, port number and protocol are mixed up.You have selected the following application to be imported from the remote server. [code]

I'm not sure where to find the Tomcat logs or how much use they would be.

View 1 Replies View Related

Cisco WAN :: 3750x - Product Registration Number

Apr 8, 2013

I just bought 2 Cisco3750 X Switches, After I open the box, there are too many numbers lables on the switch.
 
1. Which number is for product registration ?
2. Can any give me the link for product registration ?
 
BTW, can explain to me what is PAK, is it come with the switch ? Where I can find it ? I can find serial number but I don't know how to use it and connect with PAK.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Secondary Registration Failed

Jun 5, 2013

I've just had to rebuild my ACS appliance with new hardrives but I am unable to register the devices to each I get a system error. I thought it may have had something to do with the rebuilt device not being joined tothe domain but it has now been joined albeit using a different ad account, but still cannot register to primary.

View 11 Replies View Related

Cisco Routers :: SRP527W SIP Source IP Registration

Nov 5, 2012

We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
 
VPN is working fine.
 
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
 
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.

View 2 Replies View Related

Cisco Wireless :: Migrating From WISM-1 To 5508?

Feb 5, 2013

We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?

View 5 Replies View Related

Cisco Wireless :: CAT6500 - How To Log Into WISM From Switch

Apr 9, 2012

we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?

View 4 Replies View Related

Cisco Firewall ::5520 - NAT SIP Registration From Outside To Inside Interface On ASA?

Mar 7, 2012

I'm trying to NAT SIP registration from OUTSIDE interface to Inside interface on ASA

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ISE 1.1.3.124 Secondary Node Not Reachable After Registration

Jun 1, 2013

I'm constantly seeing that the sync and replication status for my secondary admin/monitor node in the primary node as node not reachable. The secondary still thinks it is in standalone mode. When I run the ISE diag tool connectivity tests I am able successfully ping the devices from each other using both hostname and ip and the nslookup also works fine between both nodes. Ping and nslookups also work from different networks within the environment. The two nodes are in the same vlan on a 6500 vss pair but on different switches of the pair.

View 6 Replies View Related

Cisco Wireless :: 5508 To Join With 2 WISM As Backup

Jun 20, 2012

I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
 
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
 
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?

2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?

3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?

View 4 Replies View Related

Cisco Wireless :: WISM V7.0 Interface Grouping With Different Subnets?

Sep 19, 2012

WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
 
Eg. VLAN1 - mask 255.255.255.248
      VLAN2 - mask 255.255.255.120
 
Would these two VLANs be able to work together in interface grouping?

View 1 Replies View Related

Cisco Wireless :: WS-SVC-WISM-1-K9 / Getting The IP From Service-vlan DHCP?

Mar 20, 2012

WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP.The pertinent config is as follows.
 
!
vlan 300
name WiSM_Service_Vlan
!interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0

[code]....

The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to it by doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
 
HO2NET0001##session switch 1 slot 4 proc 1

The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...

View 5 Replies View Related

Cisco Wireless :: WS-SVC-WISM-1-K9-D Centralized Forwarding Card

Feb 10, 2013

What this card is and what is it used for?
 
from show module command, it appears that it is a sub-module of the wism blade.
 
what is it's primary function?

View 1 Replies View Related

Cisco Wireless :: Software Upgrade Of WISM / 4400 / WCS

May 4, 2013

I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,

View 1 Replies View Related

Cisco Wireless :: 6509-E / WiSM Controller Unreachable From WCS

Jan 26, 2013

I am getting an alarm on WCS where a one controller is down, unreachable from WCS, while the other one is reachable on the same WiSM module. Upon investigation, Status of controller is shown as "Oper-Up" for all controllers on Supervisory engine. Hardware platform is Cisco 6509-E.
 
     WLAN
Slot  Controller  Service IP       Management IP    SW Version  Status
----+-----------+----------------+----------------+-----------+---------------
2     1           192.167.10.11    172.19.47.65     6.0.196.0   Oper-Up
2     2           192.167.10.12    172.19.47.66     6.0.196.0   Oper-Up
 
However, I can not ping the managment interface of the down controller while the other controller management interface is pingable. All these interfaces are in the same VLAN.
 
ping 172.19.47.65  
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.19.47.65, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

Problem is fixed when I reboot the problematic Controller. However, this problem re-appears after some time. I am not able to figure out why controller is not able to ping its default-gateway which is an SVI interface on Supervisory card on the same chassis, and showing status UP/UP. Is it a software bug or backplane fault or any other reason ?

View 1 Replies View Related

Cisco Wireless :: 6509 - WISM Not Connecting After Reboot

Apr 7, 2013

We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 is not compatible with Po407 and will be suspended (trunk mode of Gi4/1 is dynamic, Po407 is trunk)

View 13 Replies View Related

Cisco Wireless :: WS-6504E / WiSM Can't Function Normally After Upgrading From Version 6.0.182

Oct 13, 2011

I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220.When it was unstable, I found three strange condition 1. A lot of log looks like this*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/1059/stat.(erno 24)*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'fmcHsTask'2. Internal Temperature was showed "sensor failed"3. CPU User load is Zero?

View 8 Replies View Related

Cisco Wireless :: Samsung SCH-i569 Can't Work At LAP1131G With WiSM

Apr 9, 2012

The Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scanning. The phone can work at the Autonoumous mode or other 3rd party Fat AP.

View 1 Replies View Related

Cisco Wireless :: WS-6504E WiSM Can't Function Normally After Upgrading From Version 6.0.182

Mar 9, 2013

I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220. [code]

View 1 Replies View Related

Cisco Wireless :: AIR-CAP1552I - Minimum WISM Support Code?

Feb 15, 2012

I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?

View 4 Replies View Related

Cisco Wireless :: Max Number Of Mobility Member In Group With WISM 7.0

Dec 5, 2011

I have a customer buys 12 x WISM and build up a mobility, when I add the final WLC to mobility, it prompts that there mobility group has reached the max of mobility member, but the total member is 23, according the configuration guide, it should be allow to 24 member, do I hit some bug? My using version is 7.0.98.0.

View 5 Replies View Related

Cisco Wireless :: WiSM In Catalyst 6509 - Resetting To Factory Mode

Mar 7, 2012

I have been having some issues trying to stand up an older WiSM that has been incorrectly configured by my predecesssor and has a bad Mgt IP so I am unable to telnet or SSH into it, nor can I console or session into it.
 
What I would like to do is to change the Mgt address for the WiSM controllers (1 and 2) by way of the Sup (not sure that is possible) because as it stands they are set to 169.254.1.1 and are unreachable even when directly consoled into them.
 
Core-A#sh wism status
 
Service Vlan : 52, Service IP Subnet : 10.104.52.2/255.255.255.0
      WLAN
Slot  Controller  Service IP       Management IP    SW Version  Status
-------------------------------------------------------------------------------------------------------
3           1       10.104.52.3         169.254.1.1          4.0.217.0    Oper-Up
3           2       10.104.52.4         169.254.1.1          4.0.217.0    Oper-Up
 
Core-B#sh wism status
 
Service Vlan : 52, Service IP Subnet : 10.104.52.1/255.255.255.0
      WLAN
Slot  Controller  Service IP       Management IP    SW Version  Status
-------------------------------------------------------------------------------------------------------
3          1       10.104.52.50        10.104.30.254      7.0.116.0    Oper-Up
3          2       10.104.52.51        10.104.30.250      7.0.116.0    Oper-Up
 
I hope to get this WiSM setup on Core A and get it configured like I have my Core B and then run them in a dual failover design with load balancing between the two.

View 6 Replies View Related

Cisco Wireless :: 6509 - WiSM Version 6 Cannot Modify Service Interface

Jun 19, 2009

although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16   suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:

B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
 
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;

View 4 Replies View Related

Cisco Wireless :: Cat6509 - WiSM Module Not Coming In OPER-UP Status

Aug 15, 2012

The problem is WiSM module not coming in OPER-UP status , it’s in  Started-Keepalive status.I did run debug wism events on cat6509 and seeing below logs:
 
[code]...
 
It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.

View 4 Replies View Related

Cisco Wireless :: How To Create Guest Access In Wireless By WISM V 7.0 And WCS And ACS

Oct 6, 2012

how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?

View 1 Replies View Related

Cisco Wireless :: 6513 - How To Access Memory On WISM To Delete Old Boot Image

Sep 22, 2012

I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.

Midway through the transfer, the transfer stopped and I got this error on the log:

*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
 
How to access the memory on the wism to delete the old boot image?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved