Cisco :: 6500 - New WLans Not Broadcasting From WISM To APs
Aug 2, 2012
There are 8 existing W LAN's in our WISM controller & it is working fine without any problem. Now the problem is any new W LAN's are not broadcasting from WISM to APs, I am able to create & enable it in WLC but it these W LAN's are not reflecting in associated APs.
FYI: WISM controller is in 6500 switch & FWSM module also in the same switch, earlier there was rule with any any traffic in the FWSM but recently we have removed the FWSM & all rules moved to checkpoint. We have check the in firewall there is traffic is blocking.
View 18 Replies
ADVERTISEMENT
Dec 19, 2011
I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]
View 21 Replies
View Related
Mar 5, 2013
We have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.
However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.
View 7 Replies
View Related
Nov 16, 2012
Setting up a multi floor WLAN using a 6500 WISM Controller. Each floor has an AP group with the floor WAPs assigned. Each floor has a VLAN and the WLC has an interface configured. Each floor has a WLAN configured with the same SSID and the only change is the interface on the WLAN per floor.DHCP is remote on AD servers and each floor as a scope configured.Each floor works fine - we can get connected and get assigned to correct IP address. The issue we had with this setup was moving between floors. When we move up a floor the client loses connection to the inital floor (coverage - as expected). if we disconnect and reconnect it connects to the new floor SSID and gets an IP from DHCP.When looking into this - I then created an interface group and added all the floor interfaces into the group. I then applied the interface group to each floor WLAN and did soem testing - it worked as expected. I could now move between floors.The issue with this is though. When I was testing I already had an IP address assigned from DHCP - before I changed to interface groups. The issue is that the intial DHCP assignment no longer works and we cant connect to the WLAN anymore,
View 2 Replies
View Related
Jan 25, 2011
I am using Cisco Wireless LAN software revision 7 on an AIR5508. I am sure that I read somewhere that the controller will not allow 2 w lans to talk to each other but trawling back through my books I can't find the information again. Essentially, I am looking to find out if there is a feature (other than on the default gateway which is a layer 3 switch) that will say that if WLAN1 tries to talk to WLAN2 via the default gateway, the controller will not allow it.
I remember from what I read that I think this is the case but just cant find where I read it.
View 2 Replies
View Related
Sep 7, 2011
I would like to create multi-WLAN for personal communications, and gaming purposes. Each WLAN (is located in seperate house) and consists of a wireless AP wirely- connected to wireless router. The computers in each of these WLANs are connected wirelessly to the router. The houses (containing the WLANs) are locates within the region of a central wireless internet AP tower antenna.
I managed to utilize this central AP to make the connection, and make multiplayer gaming on two computers (in different houses and without using the internet services), each computer is connected to the central AP by a USB witrless adapter.My question is what are the necessary configurations that I need to make on the routers and APs? I have a number of different TP-Link routers (wr1043, wr743, wr543), micronet APs. Wr743 and 543 have AP client mode that can be used to simultaneously connecting wirelessly to central AP and to attaced computers.
View 2 Replies
View Related
Jun 7, 2011
I want to run 2 separate wireless networks from the same appliance (Linksys E2000). Not just separate BSIDs or SSIDs, I want to run an N-only AP and a G-only AP. My wife's laptop is the only wireless N device and I want to ensure that she's getting true wireless N speeds. From what I could tell, I could set up a different VLAN for 2 separate WLANs, but they'll both still both follow the 1 wireless standard (either G or N). Is this even possible or do I need to run two separate wireless APs?
View 4 Replies
View Related
Feb 16, 2013
We have inherited a 5508 controller running 7.0 code and WCS running 7.0 code. This site did not have a backup controller. So we have installed a wism as a backup controller. The problem is no one can seem to remember the pre shared keys for the wlans on the primary controller. Can I use WCS to duplicate the wlans to the secondary controller and have the psk copied?
View 3 Replies
View Related
Sep 25, 2012
when I try to enable a WLAN that is using the same SSID as another WLAN I get this message
The following errors occurred while updating the WLAN:
WLAN with duplicate SSID and L2 security policy found.
each location has its own interface because each site is setup on our 6509 with a different VLAN. What is the best way to work around this.
View 10 Replies
View Related
Sep 4, 2012
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".
WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot. Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
View 5 Replies
View Related
Sep 3, 2012
I didn't design the job, but is pretty straight forward, except the following, the design has a single wlc 5508 with 2 physical connection between two non cisco switches. There are 2 initial WLANs to be created. I am ok with most of the wlc config execpt the following:
Now from my understanding of everything I have read recently, you can't use LAG on the 2 physical connections if they connect to 2 seperate switches, unless, although not offically supported, the 2 connections are on either 2 3750s in the same stack or a pair of 6500s running VSS. So I believe that in my case 2 seperate connections from the wlc to 2 non cisco switches will not work with LAG. Is my understanding of this correct?
Is there a way to maintain the 2 physical connections from the wlc to the 2 non cisco switches to maintain redundancy?The wlc will have a management interface obviously, but from what I have read, the 2 WLANs that are going to be created have to have their own interface on the WLC. Which I understand as the managment int and each of the 2 WLANs are on different subnets.
If I don't use a single uplink to one of the non cisco switches (either 1 or 2 physical connections) using LAG, it appears to me that each of the interfaces ( management, wlan1 and wlan2) need to have a physical connection from the WLC to the switch, with each interface mapped to a physical port on the WLC, so correct me please if I am wrong, but this would mean I need 3 physical connections between the wlc and the swtich?
View 3 Replies
View Related
Jul 29, 2012
I have intel centrino n 2230 wireless card in my alienware M17X-R4. When I search for available WLANs I can see all 2.4 GHz networks but none 5 GHz.
I have Netgear WNDR3800 AP running openwrt backfire 10.03.1
settings for the AP are:
mode:802.11 a+n
HT mode: 20 Mhz
Channel: 40 (5.200 GHz)
i tried several config alternatives - no joy
i updated the driver of the intel wifi card to the latest - no joy.
View 5 Replies
View Related
Feb 15, 2013
I have a WLC 2106 which is configured and working as follows: [code] how do i get the AP at Site B to use the local server (10.0.28.x) to hand out DHCP leases?
View 3 Replies
View Related
Jan 2, 2013
We created a VLAN interface and a WLAN on the wireless controller (5508) and using it for Guest Wireless (Web auth), can we use the same VLAN and WLAN s for Wired Guests also?
View 5 Replies
View Related
Sep 7, 2011
What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?
View 5 Replies
View Related
Aug 9, 2011
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies
View Related
Nov 11, 2012
web authentication when using Android devices. I've been testing it and it seems to be caused by certificates (as it has been said in others discussions). With https disabled in the WLC (Wism 6.0.196.0), the portal authentications loads, but no with https. In addition, another issue I've detected is the DNS resolution of my controller by 1.1.1.1 when redirection takes place. With https enabled, DNS resolution and redirection works fine, so I don't think DNS server misconfiguration is the cause of the problem.I've only been able to see the portal with https disabled and entering manually 1.1.1.1/login.html
View 13 Replies
View Related
Jan 17, 2011
is there a way for pre deploying the new ap images? We have around 500 APs and my inspection windows isnt long enough to upgrade via controller......
View 6 Replies
View Related
Feb 5, 2013
We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?
View 5 Replies
View Related
Apr 9, 2012
we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?
View 4 Replies
View Related
Dec 21, 2011
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies
View Related
Oct 16, 2011
I currently have a vlan/SVI on my 6506 for the WiSM service-port. The WiSM has an address on the same subnet. To manage the WiSM, I either https to the Management interface address or use 'session slot X proc Y' from the the 6506. Since I am essentially only using two addresses from a subnet for this service-port I would like to free up the subnet. Can I keep my current functionality by having a vlan only (with the wism service-vlan XX command) with no SVI?
View 7 Replies
View Related
Feb 26, 2013
I have issue to access one of the wism on 6509 switch however other wism is ok both wism on switch are up and functional how to enable remote access on wism.
View 13 Replies
View Related
Jun 20, 2012
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
View 4 Replies
View Related
Sep 19, 2012
WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
Eg. VLAN1 - mask 255.255.255.248
VLAN2 - mask 255.255.255.120
Would these two VLANs be able to work together in interface grouping?
View 1 Replies
View Related
Dec 13, 2011
In our setup we have WiSM modules installed on cisco 6506-E, ACS 5.3 virtual appliance. We are trying to implement EAP-FAST for our Wireless using WPA/WPA2 802.1x on the WLC side.
I have followed the instructions in the following document step-by-step: [URL]
Still I have no success. Tried most of the permutations on ACS EAP-FAST configuration.
View 2 Replies
View Related
Mar 20, 2012
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP.The pertinent config is as follows.
!
vlan 300
name WiSM_Service_Vlan
!interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
[code]....
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to it by doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
View 5 Replies
View Related
Feb 10, 2013
What this card is and what is it used for?
from show module command, it appears that it is a sub-module of the wism blade.
what is it's primary function?
View 1 Replies
View Related
Oct 9, 2011
I think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies
View Related
Mar 23, 2011
my college using WisM (WS-SVC-WISM-1-K9) as wireless controller , Cisco 1130 access point and Cisco Secure ACS 4.X Solution Engine 1113 Appliance as radius server. For username and password, we take it from existing Oracle database.
The problem is the password that store in oracle database is in encrypted format. Base from feedback from database administrator, the encrpytion is done by oracle - application layer and cannot be decrypt back.
To tackle this problem, we decide to use external script in php to verify the username & password...The php script will check directly from oracle database. If the username & password match, it will sent a boolean true (1) to the Wism controller and if the username & password not match, the script will send boolean false(0) to the Wism controller.
My question is, can WiSM module talk to php script? Can it receive boolean parameter from php script?
View 5 Replies
View Related
May 4, 2013
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies
View Related
Jan 26, 2013
I am getting an alarm on WCS where a one controller is down, unreachable from WCS, while the other one is reachable on the same WiSM module. Upon investigation, Status of controller is shown as "Oper-Up" for all controllers on Supervisory engine. Hardware platform is Cisco 6509-E.
WLAN
Slot Controller Service IP Management IP SW Version Status
----+-----------+----------------+----------------+-----------+---------------
2 1 192.167.10.11 172.19.47.65 6.0.196.0 Oper-Up
2 2 192.167.10.12 172.19.47.66 6.0.196.0 Oper-Up
However, I can not ping the managment interface of the down controller while the other controller management interface is pingable. All these interfaces are in the same VLAN.
ping 172.19.47.65
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.19.47.65, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Problem is fixed when I reboot the problematic Controller. However, this problem re-appears after some time. I am not able to figure out why controller is not able to ping its default-gateway which is an SVI interface on Supervisory card on the same chassis, and showing status UP/UP. Is it a software bug or backplane fault or any other reason ?
View 1 Replies
View Related
Apr 7, 2013
We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 is not compatible with Po407 and will be suspended (trunk mode of Gi4/1 is dynamic, Po407 is trunk)
View 13 Replies
View Related
