Cisco Wireless :: WS-SVC-WISM-1-K9 / Getting The IP From Service-vlan DHCP?
Mar 20, 2012
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP.The pertinent config is as follows.
!
vlan 300
name WiSM_Service_Vlan
!interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
[code]....
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to it by doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
View 5 Replies
ADVERTISEMENT
Jun 19, 2009
although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
View 4 Replies
View Related
Oct 16, 2011
I currently have a vlan/SVI on my 6506 for the WiSM service-port. The WiSM has an address on the same subnet. To manage the WiSM, I either https to the Management interface address or use 'session slot X proc Y' from the the 6506. Since I am essentially only using two addresses from a subnet for this service-port I would like to free up the subnet. Can I keep my current functionality by having a vlan only (with the wism service-vlan XX command) with no SVI?
View 7 Replies
View Related
Nov 16, 2012
Setting up a multi floor WLAN using a 6500 WISM Controller. Each floor has an AP group with the floor WAPs assigned. Each floor has a VLAN and the WLC has an interface configured. Each floor has a WLAN configured with the same SSID and the only change is the interface on the WLAN per floor.DHCP is remote on AD servers and each floor as a scope configured.Each floor works fine - we can get connected and get assigned to correct IP address. The issue we had with this setup was moving between floors. When we move up a floor the client loses connection to the inital floor (coverage - as expected). if we disconnect and reconnect it connects to the new floor SSID and gets an IP from DHCP.When looking into this - I then created an interface group and added all the floor interfaces into the group. I then applied the interface group to each floor WLAN and did soem testing - it worked as expected. I could now move between floors.The issue with this is though. When I was testing I already had an IP address assigned from DHCP - before I changed to interface groups. The issue is that the intial DHCP assignment no longer works and we cant connect to the WLAN anymore,
View 2 Replies
View Related
Apr 20, 2012
I'm trying to configure a dhcp service on a router for some vlans.I would like to give the range 172.16.0.0 - 172.16.10.255 to vlan 10, 172.16.20.0 - 172.16.20.255 to vlan 20.for some reason it doesn't work?here's the config.
ip dhcp excluded-address 172.16.0.1
ip dhcp excluded-address 172.16.20.1
ip dhcp excluded-address 172.16.30.1
ip dhcp pool vlan10
network 172.16.0.0 255.255.0.0
[code]...
View 10 Replies
View Related
Aug 8, 2012
My problem, in a nutshell, is that clients do not get an IP from an external DHCP server when connected to a guest VLAN.
My current setup is:
Native VLAN 1 (192.168.2.x)
2008 DHCP Servers
2504 WLC
[Code].....
The guest WLAN just uses WPA and a PSK and is set to interface vlan101 There rest of the 2504 config is default.
The ports that the WLC and APs are connected to are tagged on the correct VLANs. (is that even necessary for the AP now?)
Ive changed the interface config around a hundred times now with no luck. No matter what a client will not get an IP.
Could this be due to the 2504 and ASA both acting as DHCP relays? Ive tried setting the IP of the DHCP on the dynamic interface to many different things with no luck.
View 10 Replies
View Related
Jun 13, 2012
I have an inside network using PAT to one outside address. Our DNS server is on another local, but outside address. I can't get the inside network to successfully get addresses.I have another inside address that just uses the wirewall and gets addresses just fine from the same server.I have the box checked in ASDN that enables DHCP on the inside interface and points to the correct DHCP server,PAT service is working properly if I use a hard coded address for a machine on the inside network.This is an ASA5540 with 8.3(2)
View 2 Replies
View Related
Feb 16, 2013
I have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
View 3 Replies
View Related
Oct 8, 2011
I had a virus. I think I got rid of it. Avast scans and boot time scans and Super Anti Spyware and TDSS killer report all clear. However, the network shield of Avast and the Internet don't work. Points to note: 1. In services, the DHCP and DNS cannot be started. I get the error 1075: service has been marked for deletion or one of it's dependancies are missing. (close to that)
I've checked the dependancies of both, and reinstated the ADF module in device manager after selecting the 'View Hidden' option.
View 3 Replies
View Related
Aug 8, 2012
When you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies
View Related
Feb 16, 2012
I did the config below but unable to obtain the ip from the subnet scope 10.10.9.0. The switch is in the layer 3 mode.
no spanning-tree
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
View 1 Replies
View Related
Sep 25, 2012
I have a new 5508 that I am setting up. My first one from scratch.
Interfaces:
managment -> 10.10.10.10 ->dhcp 10.10.10.1
voice -> 10.10.7.1 ->dhcp 10.10.10.1
guest -> 192.168.1.2 ->dhcp 192.168.1.2
Local DHCP (via the 5508) is for the guest network while the management and voice use the Windows DHCP server.
My problem, Voice and guest work fine. I have two SSID's (one 802.1X and the other PSK) that use the management interface that will not get an IP. I have enabled dhcp proxy from the cli on the controller. I tried with the management VLAN tagged and untagged.
View 2 Replies
View Related
Feb 7, 2013
So I have a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data. I have this router interface plugged into FA 0/24 on my 3550 and the 3550 is configured as a dot1Q trunk (I have attached configs for RTR and SW).I have most ports configured as access VLAN 1 which is where i have my ISP connection plugged FA0/1 on the 3550. When I connect the service provider link FA0/0.1 never picks up an address. If I take my internal DHCP server and connect it to FA0/1 of the 3550 it snags an address almost immediately.In my mind this validates that my config is fine. I also took the same cable from the service provider cable modem and connected it to my laptop and the laptop is pulling DHCP.
View 4 Replies
View Related
Mar 19, 2012
can you enable dhcp service on a 3560 switch.
View 3 Replies
View Related
Dec 27, 2012
My F5D8235-4 v3 constantly looses it's DHCP service and needs to be rebooted.
View 1 Replies
View Related
Dec 14, 2011
We have a Cisco Aironet 1130AG Wireless AP (firmware 12.4) and have a guest wireless network (internet only) and corporate wireless network configured on it. They are kept separate by having different VLANs assigned to them. When a laptop connects to the guest network I see the DHCP request go out and it is tagged with the correct VLAN. The problem is when a laptop connects to the corporate network I see the DHCP request go out but there is no VLAN tagged on the packets. This causes a problem because both of our DHCP servers (on VLAN 1 and 3, remote DHCP servers no DHCP running on the Aironet [Doesn't seem like this version has a DHCP server]) are sending responses and sometimes the corporate user will get an IP address on the Guest subnet.
Our corporate network is setup on VLAN 1 which is configured as the Native VLAN on the Aironet. Will this cause the Aironet not to tag these packets with any VLAN information? Any other thoughts as to why it isn’t tagging these packets to a VLAN?
View 3 Replies
View Related
Sep 25, 2012
My Network Layout is as, Firewall (with Routing)------>Cisco 3560 Switch (L3)------> connected 8 Cisco 2960 switch (L2)----> all users I have configured 20 VLAN's on cisco 3560 switch with Dynamic Pool and Static, Means, 5 Vlan's are Dynamic and remaining are Static Our Company process provides only internet access to existing clients computers. Problem is that, I configured Static VLAN 5 for one of our Client in their seperate room, mean to say, i activated all ports of their room with Static VLAN 5. one day they configured own DHCP server on Windows 2003 Server with same subnet (Same as VLAN5) in their room without any information and now their all computer/ Laptop acquiring ip address Dynamically.
If i have configured Static vlan on that port's then how it is get Dynamic ip from same port's.How to restrict to permit another DHCP server/Service in our premises. I Do not want to give administrative control to Clients to do such kind of thing with LAN.
View 8 Replies
View Related
Feb 23, 2012
In our test set up, we have two WLC 5508 Controllers connected via Checkpoint UTM-1 firewall Inside and DMZ Interfaces. Both the WLC controllers are connected to the firewall via Cisco 3750 switch. On the Local (Inside) Controller, guest SSID is enabled and attached to the wireless management Interface. On the remote anchor controller, guest SSID is enabled and attached to the Management Interface as well. The following configs are replicated on both the Controllers.
SSID Name - guest
Interface - Management ( VLAN 10 on Local and VLAN 20 on remote) -
Mobility Group: Same configs at both ends
SSID Anchor : Anchor SSID on local and local SSID on Anchor.
AP: CAPWAP 3502 Management Subnet
[code]....
Is there any thing missing in the wireless configs and or the firewall rules as i could not see DHCP request back from the Anchor Controller. Also, after DHCP is obtained, the web authentication request will be redirected to an Amigopod device for authentication. In this case is the redirect URL congiguration to be performed only on the Anchor Controller or is this to be replicated on both the Local and Anchor Controllers.
View 8 Replies
View Related
Feb 20, 2013
I have a asa 5510 vpn client groups configured and connected to the internal network DHCP server stops giving network service dhcp and the network goes down.
View 6 Replies
View Related
Feb 5, 2013
We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?
View 5 Replies
View Related
Dec 19, 2011
I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]
View 21 Replies
View Related
Apr 9, 2012
we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?
View 4 Replies
View Related
Mar 5, 2013
We have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.
However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.
View 7 Replies
View Related
Oct 15, 2012
I have a firewall that I want acting as a DHCP relay. This firewall has a number of VLAN interfaces serving clients. The DHCP relay destination is the IP address of a Windows 2012 Server running Microsoft DHCP which has multiple scopes configured, one for each client VLAN.What I'm finding confusing is how the DHCP will identify the client. Does the DHCP relay insert an identifier of some sort (opt. 54?) based on which VLAN the DHCPREQUEST comes from and then this identifier can be configured to be recognized on the DHCP server?
View 2 Replies
View Related
Apr 14, 2013
I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies
View Related
Jan 18, 2013
I have a 2620 Cisco Router plugged into a 2924 Cisco switch by a trunk.The vlan configuration works, I subdivide my router interface with dot1q and have virtual machines on different vlans and everything works perfectly.The problem comes with a DHCP request.Let's say that I have my local lan on the native VLAN 1. I create a VLAN 25 in the switch and create a fa0/0.25 in the router.In the switch, I plug the cable modem from my ISP in a port on vlan 25In the router, I go to fa0/0.25 and issue "ip address dhcp".The DHCP request goes out, but never comes back. The problem seems to be in the switch because if I try the same thing with a virtual machine I have on a trunked VMWare ESXi server, I get the exact same results. I just don't get the IP address from the ISP.The next step would be to monitor the port on which the cable modem is connected and sniff the packets to see if the DHCP request actually gets back through.
View 2 Replies
View Related
Jan 22, 2012
We have a server that we remove from the rack. The only role it has is to give out DHCP on the wireless network. I tried enabling the built in DHCP server on the Airespace 4112, though a Catalyst 3750G, but I dont get an address when I'm connected to the wireless network even though the range is enabled. If I set an static IP on my wireless card I can access the network. I also tried enabling DHCP on a Sonicwall that is connected to the Catalyst 3750G.
Do I need to link the DHCP scope to the wireless network? Is there anything on the switch that would be blocking DCHP since it on a VLAN? I have the last four ports in a VLAN for the AP's and the internet connection to the Sonciwall.
View 6 Replies
View Related
Jan 2, 2013
I have a Cisco RV220W router (firmware version 1.0.4.17).
I would like to have two separate networks with the following specifications:
Netwrork1: address range for the network is 192.168.0.1-254. All devices should be able to reach eachother within this network and connect to the internet either on LAN or through Wifi. From this network I should also be able to reach the device management page of the router. Also the devices should get the ip addresses throgh DHCP.
Network2: address range for the network is 192.168.5.1-254. All devices within this network should not be able to reach the devices in network1. All devices on this network should reach the internet through Wifi only. Device management page should not be available on this network.
I have configured the router as shown in the attached screenshots but the problem is that in Network2, devices get IPs from the 192.168.0.1-254 range and not from the 192.168.5.1-254 range. Also there is no internet on these either.
View 8 Replies
View Related
Jan 16, 2011
I have just upgraded our WLC from 4.0 to 7.0 (via 4.2). Before the upgrade we had our ACS returning a VLAN based on user group. This seemed to be working without an issue. Now that the WLC is on version 7 this is no longer working correctly. The ACS is returning a VLAN and passing the user but the client can not get an IP from the DHCP server configured.
Example configuration:
SSID-----VLAN
PN-CSC-----CSCVlan: Works
PN-Others------OthersVlan: Works
PN-Others-----CSCVlan: No DHCP
When users are trying to be allocated to a vlan that is different from the native one the DHCP fails however both WLANs are configured to point to the management interface so dont have any real connection to the vlan other than by name.
Have there been any changes I haven't seen in the way the dynamic vlan allocation works in version 7?
View 8 Replies
View Related
Jun 20, 2012
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
View 4 Replies
View Related
Sep 19, 2012
WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
Eg. VLAN1 - mask 255.255.255.248
VLAN2 - mask 255.255.255.120
Would these two VLANs be able to work together in interface grouping?
View 1 Replies
View Related
Feb 10, 2013
What this card is and what is it used for?
from show module command, it appears that it is a sub-module of the wism blade.
what is it's primary function?
View 1 Replies
View Related
May 4, 2013
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies
View Related
