I dont think my cards are faulty (4 cards in 2 6500 switches),I connect directly to my WISM cards, boot them (insert them), I see it turning on, enabling services, and as soon as the "username:" prompt apears, the Status led turns off and I lose console. [code]
View 21 RepliesWe have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.
However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.
Setting up a multi floor WLAN using a 6500 WISM Controller. Each floor has an AP group with the floor WAPs assigned. Each floor has a VLAN and the WLC has an interface configured. Each floor has a WLAN configured with the same SSID and the only change is the interface on the WLAN per floor.DHCP is remote on AD servers and each floor as a scope configured.Each floor works fine - we can get connected and get assigned to correct IP address. The issue we had with this setup was moving between floors. When we move up a floor the client loses connection to the inital floor (coverage - as expected). if we disconnect and reconnect it connects to the new floor SSID and gets an IP from DHCP.When looking into this - I then created an interface group and added all the floor interfaces into the group. I then applied the interface group to each floor WLAN and did soem testing - it worked as expected. I could now move between floors.The issue with this is though. When I was testing I already had an IP address assigned from DHCP - before I changed to interface groups. The issue is that the intial DHCP assignment no longer works and we cant connect to the WLAN anymore,
View 2 Replies View RelatedThere are 8 existing W LAN's in our WISM controller & it is working fine without any problem. Now the problem is any new W LAN's are not broadcasting from WISM to APs, I am able to create & enable it in WLC but it these W LAN's are not reflecting in associated APs.
FYI: WISM controller is in 6500 switch & FWSM module also in the same switch, earlier there was rule with any any traffic in the FWSM but recently we have removed the FWSM & all rules moved to checkpoint. We have check the in firewall there is traffic is blocking.
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
We are currently upgrading from WISM-1's to individual 5508 WLC's. Is it possible to export the config from controller on the WISM to the 5508?
View 5 Replies View Relatedwe have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?
View 4 Replies View RelatedI have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
Eg. VLAN1 - mask 255.255.255.248
VLAN2 - mask 255.255.255.120
Would these two VLANs be able to work together in interface grouping?
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP.The pertinent config is as follows.
!
vlan 300
name WiSM_Service_Vlan
!interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
[code]....
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to it by doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
What this card is and what is it used for?
from show module command, it appears that it is a sub-module of the wism blade.
what is it's primary function?
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies View RelatedI am getting an alarm on WCS where a one controller is down, unreachable from WCS, while the other one is reachable on the same WiSM module. Upon investigation, Status of controller is shown as "Oper-Up" for all controllers on Supervisory engine. Hardware platform is Cisco 6509-E.
WLAN
Slot Controller Service IP Management IP SW Version Status
----+-----------+----------------+----------------+-----------+---------------
2 1 192.167.10.11 172.19.47.65 6.0.196.0 Oper-Up
2 2 192.167.10.12 172.19.47.66 6.0.196.0 Oper-Up
However, I can not ping the managment interface of the down controller while the other controller management interface is pingable. All these interfaces are in the same VLAN.
ping 172.19.47.65
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.19.47.65, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Problem is fixed when I reboot the problematic Controller. However, this problem re-appears after some time. I am not able to figure out why controller is not able to ping its default-gateway which is an SVI interface on Supervisory card on the same chassis, and showing status UP/UP. Is it a software bug or backplane fault or any other reason ?
We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 is not compatible with Po407 and will be suspended (trunk mode of Gi4/1 is dynamic, Po407 is trunk)
View 13 Replies View RelatedI have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220.When it was unstable, I found three strange condition 1. A lot of log looks like this*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/1059/stat.(erno 24)*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'fmcHsTask'2. Internal Temperature was showed "sensor failed"3. CPU User load is Zero?
View 8 Replies View RelatedThe Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scanning. The phone can work at the Autonoumous mode or other 3rd party Fat AP.
View 1 Replies View RelatedI have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220. [code]
View 1 Replies View RelatedI am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies View RelatedI have a customer buys 12 x WISM and build up a mobility, when I add the final WLC to mobility, it prompts that there mobility group has reached the max of mobility member, but the total member is 23, according the configuration guide, it should be allow to 24 member, do I hit some bug? My using version is 7.0.98.0.
View 5 Replies View RelatedI have been having some issues trying to stand up an older WiSM that has been incorrectly configured by my predecesssor and has a bad Mgt IP so I am unable to telnet or SSH into it, nor can I console or session into it.
What I would like to do is to change the Mgt address for the WiSM controllers (1 and 2) by way of the Sup (not sure that is possible) because as it stands they are set to 169.254.1.1 and are unreachable even when directly consoled into them.
Core-A#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.2/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.3 169.254.1.1 4.0.217.0 Oper-Up
3 2 10.104.52.4 169.254.1.1 4.0.217.0 Oper-Up
Core-B#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.50 10.104.30.254 7.0.116.0 Oper-Up
3 2 10.104.52.51 10.104.30.250 7.0.116.0 Oper-Up
I hope to get this WiSM setup on Core A and get it configured like I have my Core B and then run them in a dual failover design with load balancing between the two.
although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
The problem is WiSM module not coming in OPER-UP status , it’s in Started-Keepalive status.I did run debug wism events on cat6509 and seeing below logs:
[code]...
It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.
how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?
View 1 Replies View RelatedI'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies View Relatedweb authentication when using Android devices. I've been testing it and it seems to be caused by certificates (as it has been said in others discussions). With https disabled in the WLC (Wism 6.0.196.0), the portal authentications loads, but no with https. In addition, another issue I've detected is the DNS resolution of my controller by 1.1.1.1 when redirection takes place. With https enabled, DNS resolution and redirection works fine, so I don't think DNS server misconfiguration is the cause of the problem.I've only been able to see the portal with https disabled and entering manually 1.1.1.1/login.html
View 13 Replies View Relatedis there a way for pre deploying the new ap images? We have around 500 APs and my inspection windows isnt long enough to upgrade via controller......
View 6 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedI currently have a vlan/SVI on my 6506 for the WiSM service-port. The WiSM has an address on the same subnet. To manage the WiSM, I either https to the Management interface address or use 'session slot X proc Y' from the the 6506. Since I am essentially only using two addresses from a subnet for this service-port I would like to free up the subnet. Can I keep my current functionality by having a vlan only (with the wism service-vlan XX command) with no SVI?
View 7 Replies View RelatedI have issue to access one of the wism on 6509 switch however other wism is ok both wism on switch are up and functional how to enable remote access on wism.
View 13 Replies View RelatedIn our setup we have WiSM modules installed on cisco 6506-E, ACS 5.3 virtual appliance. We are trying to implement EAP-FAST for our Wireless using WPA/WPA2 802.1x on the WLC side.
I have followed the instructions in the following document step-by-step: [URL]
Still I have no success. Tried most of the permutations on ACS EAP-FAST configuration.
I think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies View Relatedmy college using WisM (WS-SVC-WISM-1-K9) as wireless controller , Cisco 1130 access point and Cisco Secure ACS 4.X Solution Engine 1113 Appliance as radius server. For username and password, we take it from existing Oracle database.
The problem is the password that store in oracle database is in encrypted format. Base from feedback from database administrator, the encrpytion is done by oracle - application layer and cannot be decrypt back.
To tackle this problem, we decide to use external script in php to verify the username & password...The php script will check directly from oracle database. If the username & password match, it will sent a boolean true (1) to the Wism controller and if the username & password not match, the script will send boolean false(0) to the Wism controller.
My question is, can WiSM module talk to php script? Can it receive boolean parameter from php script?