Linksys :: E2000 - Multiple WLANs With Same AP?
Jun 7, 2011
I want to run 2 separate wireless networks from the same appliance (Linksys E2000). Not just separate BSIDs or SSIDs, I want to run an N-only AP and a G-only AP. My wife's laptop is the only wireless N device and I want to ensure that she's getting true wireless N speeds. From what I could tell, I could set up a different VLAN for 2 separate WLANs, but they'll both still both follow the 1 wireless standard (either G or N). Is this even possible or do I need to run two separate wireless APs?
View 4 Replies
ADVERTISEMENT
Sep 25, 2012
when I try to enable a WLAN that is using the same SSID as another WLAN I get this message
The following errors occurred while updating the WLAN:
WLAN with duplicate SSID and L2 security policy found.
each location has its own interface because each site is setup on our 6509 with a different VLAN. What is the best way to work around this.
View 10 Replies
View Related
Feb 13, 2011
I'm having trouble getting our xboxes to show up as open on Xbox Live. I was able to do it for one xbox by assigning static IP and doing port forwarding, but this doesn't work for more than one. I have now done every option I can find and get the same result of moderate NAT no matter what. I have entered the ports in port range triggering, tried UPnP both on and off, filter anonymous internet requests is disabled, filter NAT redirection disabled, and have upgraded the firmware. I don't know if there is anything that can even be done at this point. On a previous router I had this issue was very simple and just had to disable a certain NAT box but with this new one nothing seems to work.
View 7 Replies
View Related
Sep 7, 2011
I would like to create multi-WLAN for personal communications, and gaming purposes. Each WLAN (is located in seperate house) and consists of a wireless AP wirely- connected to wireless router. The computers in each of these WLANs are connected wirelessly to the router. The houses (containing the WLANs) are locates within the region of a central wireless internet AP tower antenna.
I managed to utilize this central AP to make the connection, and make multiplayer gaming on two computers (in different houses and without using the internet services), each computer is connected to the central AP by a USB witrless adapter.My question is what are the necessary configurations that I need to make on the routers and APs? I have a number of different TP-Link routers (wr1043, wr743, wr543), micronet APs. Wr743 and 543 have AP client mode that can be used to simultaneously connecting wirelessly to central AP and to attaced computers.
View 2 Replies
View Related
Jan 25, 2011
I am using Cisco Wireless LAN software revision 7 on an AIR5508. I am sure that I read somewhere that the controller will not allow 2 w lans to talk to each other but trawling back through my books I can't find the information again. Essentially, I am looking to find out if there is a feature (other than on the default gateway which is a layer 3 switch) that will say that if WLAN1 tries to talk to WLAN2 via the default gateway, the controller will not allow it.
I remember from what I read that I think this is the case but just cant find where I read it.
View 2 Replies
View Related
Jul 29, 2012
I have intel centrino n 2230 wireless card in my alienware M17X-R4. When I search for available WLANs I can see all 2.4 GHz networks but none 5 GHz.
I have Netgear WNDR3800 AP running openwrt backfire 10.03.1
settings for the AP are:
mode:802.11 a+n
HT mode: 20 Mhz
Channel: 40 (5.200 GHz)
i tried several config alternatives - no joy
i updated the driver of the intel wifi card to the latest - no joy.
View 5 Replies
View Related
Aug 2, 2012
There are 8 existing W LAN's in our WISM controller & it is working fine without any problem. Now the problem is any new W LAN's are not broadcasting from WISM to APs, I am able to create & enable it in WLC but it these W LAN's are not reflecting in associated APs.
FYI: WISM controller is in 6500 switch & FWSM module also in the same switch, earlier there was rule with any any traffic in the FWSM but recently we have removed the FWSM & all rules moved to checkpoint. We have check the in firewall there is traffic is blocking.
View 18 Replies
View Related
Feb 16, 2013
We have inherited a 5508 controller running 7.0 code and WCS running 7.0 code. This site did not have a backup controller. So we have installed a wism as a backup controller. The problem is no one can seem to remember the pre shared keys for the wlans on the primary controller. Can I use WCS to duplicate the wlans to the secondary controller and have the psk copied?
View 3 Replies
View Related
Sep 4, 2012
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".
WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot. Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
View 5 Replies
View Related
Sep 3, 2012
I didn't design the job, but is pretty straight forward, except the following, the design has a single wlc 5508 with 2 physical connection between two non cisco switches. There are 2 initial WLANs to be created. I am ok with most of the wlc config execpt the following:
Now from my understanding of everything I have read recently, you can't use LAG on the 2 physical connections if they connect to 2 seperate switches, unless, although not offically supported, the 2 connections are on either 2 3750s in the same stack or a pair of 6500s running VSS. So I believe that in my case 2 seperate connections from the wlc to 2 non cisco switches will not work with LAG. Is my understanding of this correct?
Is there a way to maintain the 2 physical connections from the wlc to the 2 non cisco switches to maintain redundancy?The wlc will have a management interface obviously, but from what I have read, the 2 WLANs that are going to be created have to have their own interface on the WLC. Which I understand as the managment int and each of the 2 WLANs are on different subnets.
If I don't use a single uplink to one of the non cisco switches (either 1 or 2 physical connections) using LAG, it appears to me that each of the interfaces ( management, wlan1 and wlan2) need to have a physical connection from the WLC to the switch, with each interface mapped to a physical port on the WLC, so correct me please if I am wrong, but this would mean I need 3 physical connections between the wlc and the swtich?
View 3 Replies
View Related
Feb 15, 2013
I have a WLC 2106 which is configured and working as follows: [code] how do i get the AP at Site B to use the local server (10.0.28.x) to hand out DHCP leases?
View 3 Replies
View Related
Jan 2, 2013
We created a VLAN interface and a WLAN on the wireless controller (5508) and using it for Guest Wireless (Web auth), can we use the same VLAN and WLAN s for Wired Guests also?
View 5 Replies
View Related
Sep 7, 2011
What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?
View 5 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Feb 26, 2011
I bought this router because it had gigabit and because it was cheap /w good reviews. I was wondering what DD-WRT is (I know it's some sort of firmware) and what does it do. I use the wireless network mostly for gaming and streaming movies. How can I install DD-WRT (if it's better than the Linksys firmware)
View 7 Replies
View Related
Jan 22, 2011
I have a linksys WVC200 Internet camera and a Linksys E2000 Router.I cannot get the camera to connect to the E2000 via wireless, using a network cable no problems.Yet It works perfectly wireless and wired if I cannect the WVC200 Camera to a Belkin N1 Router. Linksys WVC200 - Linksys E2000does NOT WORK! Yet Linksys WVC200 Camera to Belkin N1 Router wsorks perfectly?
View 1 Replies
View Related
Sep 28, 2011
I have lost my wireless connection. I was wondering if somehow it got turned off on my Linksys E2000
View 1 Replies
View Related
Feb 2, 2013
I need to get my tablet set uo with Linksys E2000 router
View 1 Replies
View Related
Jul 2, 2012
About a month ago I set up FTP on my QNap for the first time. To my surprise I was able to connect to it from an outside network with no further configuration needed. Since then I have had a bit of an issue with firmware. I ended up wiping and upgrading the QNap. Since then I am unable to connect. Some resources are saying the only problem is that I don't have port forwarding set up. I guess my default router settings were already set up to forward the port (I'm not sure how to confirm) because it worked originally, the only thing that changed is my QNap settings. I would like to be able to use it as a FTP, MySQL database, and a few other things. Will I have to do a different configuration for each one?
My network set up is like this: Verizon Router/Modem -> Linksys Router e2000 -> Qnap (ethernet)
I accessed my verizon router and under port forwarding it says "Protocol: FTP, Ports: TCP Any -> 21". NAT is disabled on the Linksys so does that mean I won't have to configure it at all because it is set up in bridged mode as a dummy switch?
What IP should I be using to try to access it remotely?
When I try to connect to my QNap IP I get this in Filezilla:
Status:Connecting to 192.168.1.22:21...
Status:Connection established, waiting for welcome message...
[Code].....
View 1 Replies
View Related
May 10, 2011
what would be the easiest way of blocking a mac address from LAN not wireless, the router is Linksys E2000 and the reason isnt important, just that i want to do it, i have full access to router
View 7 Replies
View Related
Mar 25, 2011
i have just connected my linksys e2000 to the internet now i would like to set it up so other computers can connect to the internet through it wired/ wireless
View 1 Replies
View Related
Mar 13, 2012
How can i use Linksys E2000 rounter as a Access point ?
View 1 Replies
View Related
Aug 5, 2011
Can i move my linksys e2000 router to a new computer and if so how do i go about it
View 2 Replies
View Related
Jan 21, 2011
Can I hook up an antenna booster for linksys E2000? Where does it plug in if so?
View 4 Replies
View Related
Jul 12, 2011
Because of limited budget and a paranoid boss, the MS Access database at work is running through a simple Linksys wireless E2000 N router rather than a more dedicated server setup.A desktop server PC is storing the Access database and 3-4 laptops are connecting to the split database linked tables via laptop wireless N adapters only.Upon having several people accessing and updating records we've noticed a huge amount of instability frequent network interruptions.I have several theories/observations:
1) While not an ideal location (one end of the building), signal strength is consistently shown as 4/5 bars to 5/5 bars, even through several walls
2) Interference: Several other routers, all on 2.4Ghz could be creating too much interference. (none of the laptops support 5Ghz)
3) Number of individuals accessing the database at one time. This is where I'm unclear. Could having 3-4 people working on the database at once pose any potential problems? I'd ordinarily think not but I am coming up short with explanations.
Last week two of us were working with the database, updating records and such, from probably 100 ft or more away with no issues. Then the last few days just to stay connected requires being within 5-10 feet of the router AT MOST. No settings have been changed and network disconnects/interruptions in Access are happening every few minutes.
View 4 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
May 28, 2012
I've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies
View Related
Apr 24, 2011
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies
View Related
Aug 28, 2011
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies
View Related
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
View 2 Replies
View Related
