Linksys Wireless Router :: E2000 - How To Keep Speed At 300 M
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
The smile was big when I bought my new Linksys E2000 Wireless Router.
Unfortunately the smiled stiffened when I realised that the network speed did not meet the expected up to 300 Mbps for Wireless and x10 for a Giganet connection. What to do to improve the LAN speed to an acceptable level ?
Network:
* Linksys E2000 ; WPA2 (Personal) * x2 Windows7 Laptop ; x1 Linux Laptop ; x1 Qnap TS-409 Pro * Download speed WiFi (between laptops as well as from NAS) <2MB/Sec * Download Speed Cable (between laptops as well as from NAS) <8MB/Sec * Download speed with direct connection to NAS (without switch) ~13 MB/sec
I have an E2000 Wireless N Router setup to use WPA2/AES. I have Comcast cable internet service and I just upgraded to the 50Mbps speed. I have a Motorola Surfboard modem (DOCSIS 3.0).
If I connect my computer directly to the modem or to one of the ports on the E2000 I get great speeds sometimes up to 60Mbps but on average I am getting 45-48Mbps which is acceptable.
When I try to connect the same computer to the E2000 wirelessly my speed tests return a horrible 18-22Mbps. When I run these tests the computer is in the same room as the router. As I move throughout my house the speed tests are the same. My wireless connection speed to my laptop is good 144Mbps and 300Mbps depending on the band (2.4 or 5.0).
I have tried to use the 2.4ghz and 5.0ghz using different channels. I have also tried different "N Transmission Rate" settings. One of them (5 - 52Mpbs) does increase the speed to around 25-26Mpbs but that is all.
Strangely (or maybe not) the upload speeds are consistent on all of the tests at around 12Mpbs.
I am using Speedtest.net and Speakeasy for all of my tests.
Is there anyway I can get my wireless download speed up to around 40Mpbs? Or am I going to have to run cables through my house to the devices where I need these high speeds?
I also have upgraded to the latest firmware version.(1.0.04)
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
I bought an E2000 router as a replacement for my WRT54G router, since my internet speeds had been upgraded. But this E2000 router has been giving me nothing but trouble.
Wired through both the router or modem, I get my topspeed of 110mbps. However, as soon as I switch over to the wireless N function, my speed drops to only 25mbps. As far as I know, wireless N should have a much faster speed than that. Even my old WRT54G had faster speeds than this new router has. Mind you, that the distance between my laptop and router is about 3 inches away. The further I go away from my router, the speed exponentialy drops (20 feet, and the speed even drops to below 10mbps). Even with different laptops that have completely different wireless cards. Now honestly, I have tried EVERYTHING to get the speed up. Both 2.4 and 5ghz, 20mhz only, 40 mhz only, different channels (currently the router is in channel 11, being the only router in that channel), setting the network to G-only. I tried changing the Beacon interval thing in numerous settings, I even tried changing the MUT. Firmware is completely up to date. I have also tried placing the router on a completely different place, to make sure there was absolutely no interference (tough that shouldn't be an issue if my laptop is only 3 inches away) I tried changing the security mode to something different than WPA2/AES.
Nothing worked, if anything, it made it worse in some cases. I have litteraly tried every option I could find online, except for trying a third party firmware like DDWRT, which worked excellently for my old WRT54G, though I read that speeds can't be improved on this E2000 with a third party firmware.
Is there anything else I can do, or should I assume that my router is defective?
When I'm in my bedroom, I get a very poor connection and my speed drops to about 0.25mbps. Abysmal, so I bought a WiFi range extender to get me a better signal. It works, and it allows me to get a speed of about 5-6 mbps, without dropped connections. Still slow, but at least it works. The weird thing is, wired through my router or modem, I get about 9mbps upload speed. With this extender, I get the same 9mbps upload speed in my bedroom, though only 5-6 mbps download speed. You'd think that the upload speed would drop simultaneously with the download speed. How can my upload speed be higher (maxing out) than my download speed? I wonder if my transmitting antenna of my router isn't defective.
How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
My problem occurs when i am trying to download something big, mainly the speed of the download raises at a peak and then it drops disconnecting me from the internet for a few seconds. This only happens when my laptop is on a wireless connection and this phenomenon repeats itself untill the download is complete. During the connection crash I am not able to access any site.
My laptop is an Asus G series with Win7 64bit SP1, and I use utorrent for P2P downloads.
I just bought a refurbished E2000 wireless-n router with 1 Gb LAN ports (from Cisco online).This router is meant to replace my Netgear wireless-n router that only have 100 Mb LAN ports.I have 10 devices in my home network, 6 of them are using wireless (1 'g' and 5 'n') and 4 are interconnected with cat5e cables (trough the router).The devices have some different operating systems and their network adapters are from different brands.When I set up the Netgear router I didn't have to adjust anything for the wireless network to work fine.All wireless-n devices worked at 150 Mbps (sometimes going down shortly to 130 Mbps).The wireless-g device worked at 54 Mbps.For the last 2 days I've been trying to set up the E2000 to achieve a wireless-n speed higher then 72 Mpbs... without success.I tried all the suggestions that I found in the Cisco Knowledge Base.
- Upgrading the firmware to the latest version
- Trying different channels and channel widths
- Different wireless security methods and many others.
Also trying different settings on the different devices doesn't work.Changing the distance between router and devices as well as changing the location of the router don't affect the results.Switching on only 1 device at a time doesn't change anything either.It looks like the E2000 is set to not transmit on a higher speed than 72 Mbps, when it's actually supposed to achieve a wireless-n speed of up to 300 Mbps. I would be lucky if I get the half of it, but not if it's only one fourth.
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
For Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
I have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
For some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
I want to set up another wireless laptop to access my e2000 but i dont remember the network key, How can I retirieve the key? through cisco connect maybe?
E2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
I have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
my internet connection cuts in and out so my computer cant connect to the router and it wont show up. I am on a windows 7 toshiba laptop and i have comcast as my internet service provider.
