I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 RepliesI have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies View RelatedI have a Linksys E2000 router that is connected to my cable modem. I have a desktop computer that is connected to the router via an ethernet cable, and two laptops in the house that connect wirelessly to the router to get internet access.
This morning, all devices were connected to the internet just fine. I stepped away for a few hours and during that time the desktop 'lost' its internet connection. I have tried re-booting the router and removing-reconnecting the ethernet cable but nothing is restoring the connection.
The fact that my wireless devices are connecting means my internet service is fine, right? So what is preventing the desktop from gaining a connection?
Just replaced my older Cisco router with an E2000 and now none of the connected PCs can ping each other. I have two wired and two wireless nodes on the 192.168.1.X subnet (defaults) using DHCP. All nodes can access the Internet with no problems, but none of them can see each other -- no ping, no Network Neighborhood, nothing. Since this all worked fine before I swapped routers and I've made no changes on any of the nodes, I presume this is something about the router.
I've tried all the usual troubleshooting steps (spent 10 years working as Systems Engineering in IP networking) - no luck. I've also tried various settings of the router (e.g. turned off SPI) but no luck either.
my new router doesn't block connections between attached PCs on the same subnet ....
P.S. One strange observation : using Wireshark I can see the pinging node (.137) ARP for the destination IP (.102), and the ARP reply is sent by the destination node (.102) , but it looks like the Echo Request never makes it to the target machine -- i.e. I think the router is blocking it.
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies View RelatedI have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies View Relatedwas wondering if i go wired but through the router is it still being effected by the extra step or is that only going to effect wireless? asking because my wife is wireless but barely gets on, so if im about to do something intensive online would it be worth bypassing the router and plugging straight into the modem
View 2 Replies View RelatedI would like to put an E2000 in an office where clients are coming and going throughout the day. When the documentation says that there is a maximum of 10 guest network users allowed (with a default setting of 5) what exactly does that mean ? I don't want the first 10 guest-clients who come in, connect to the guest network, then leave the office to consume all 10 slots for the day.If I have 50 people that come and go from the office throughout the day who connect to the guest 192.168.33.X network and attempt to enter the password (but no more than 10 guests authenticated at any given time) will all 50 be successful in connecting ? Or do I have to reduce the Client Lease Time to something less than the default setting of one day ?
View 1 Replies View RelatedI recently purchased a 20ft Ethernet cable to speed up my internet connection. On wireless, I would download files at about 2 MB/s. On wired I get 1.5 MB/s. Is it supposed to be like this
View 1 Replies View RelatedI have internet thru Century Link (DSL). I also have a Netgear N-300 wireless router. My computer is 4 years old and is an HP with a G wireless adapter buit-in. Until yesterday, my provided internet speed was up to 7mbps. I received the same speed regardless of whether my computer was plugged in directly to the modem (1), plugged directly into the router (2), or wirelessly. We just upgraded our internet to 40mbps. Now, I get the 40 mbps when my computer is plugged into the modem or router, but wirelessly I only get about 4 mbps, 1/10th of what I get with wired.
View 3 Replies View RelatedI seem to have an issue when with my new E2500 router Version 1 (upgraded to the new fireware - today to elimate issues with that).I had RCN installed a 50MB connection today.When I connect directly to the Modem, I get almost the 50MB of the server, see link from the speedtest. [URL]. However, when i plug the ethernet cable from my Cable Modem to my Wireless Router I get around 15-20MB. Here is an example:[URL]. I know speeds can vary, but if i unplugged and rest within seconds i get my expected 50MB.The cable modem is in the living room, right next to the Wireless Router. I am situated less than 2 metres from the devices when I get results and have full bars.I've tried varying the MTU on manual and also enabled it to adjust as required.
View 8 Replies View Relatedmy linksys e1000 router compares pretty well to my modem when the Ethernet cable is hooked up. I get fast DL speeds above 50Mbps either way when the Ethernet cable is plugged into my computer. However, when I connect wirelessly, regardless of range I can't seem to DL any faster than 20Mbps. I went ahead and restored my factory defaults so that I could use Cicsco Connect and upgrade the firmware, but beyond that I don't know what settings to tweak.
View 6 Replies View RelatedAfter changing name and password, the speed became much slower. Checking it with speed test, download is just 0.19 Mbps while upload is 3 Mbps. Wired speed is much better, download is 20 Mbps. So it is not the problem of I provider, comcast. How to solve this problem? I rebooted and reset it already.
View 8 Replies View RelatedI am getting very slow download speeds on my wireless router (Linksys model#WRT160N). I measured it on speedtest.net. with my ASUS laptop, ASUS Transformer Prime tablet, and 2 Ipod touches. All similar speeds.
Download avg: 1.30 Mbps
upload avg: 6.20 Mbps
I measured my desktop speed that is hardwired through the router to the modem.
Download avg: 30.00 Mbps
upload ave: 6.20 Mbps
I have scanned all the wireless connection in my area and found them to occupy channels 1, 6, 11. I tried changing my channels one at a time for all 11 channels. Some did a little better than others but not a lot.Also, if I by a dual channel router, can all wireless devices pick up on the 5GHz spectrim and if some, could this alleviate some interference?Is it possible that my router is going bad and a new single channel 2.4 GHz router will be fine?
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
For Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies View RelatedIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 Replies View RelatedI have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies View RelatedFor some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies View RelatedI got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies View Related