Linksys Wired Router :: E2000 / E3000 - How Many Guest Clients Allowed In A Day
Jan 26, 2011
I would like to put an E2000 in an office where clients are coming and going throughout the day. When the documentation says that there is a maximum of 10 guest network users allowed (with a default setting of 5) what exactly does that mean ? I don't want the first 10 guest-clients who come in, connect to the guest network, then leave the office to consume all 10 slots for the day.If I have 50 people that come and go from the office throughout the day who connect to the guest 192.168.33.X network and attempt to enter the password (but no more than 10 guests authenticated at any given time) will all 50 be successful in connecting ? Or do I have to reduce the Client Lease Time to something less than the default setting of one day ?
View 1 Replies
ADVERTISEMENT
Oct 17, 2012
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies
View Related
Sep 19, 2011
I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies
View Related
Jul 10, 2011
which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
Wired clients count as wireless clients??
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?
View 2 Replies
View Related
Feb 12, 2013
How do I reenable guest access on my e2000 without having cisco connect installed?
View 1 Replies
View Related
May 31, 2010
I have an E2000 setup with the Cisco Connect Utility. I have a MAIN account and a GUEST account setup.I'm recently having a problem where I can only connect wireless through the "Guest" account. I can connect to my MAIN account, but it states that I have "Limited Access".
View 9 Replies
View Related
Jul 16, 2011
I tried to extend the Range of the Guest WLAN of the E2000 with several different Access Points vom TP-Link. (Last try: TL-WA901D) The Access Point recognises the WLAN and sometimes it has a connection for a short time. But then the whole WLAN is breaking down, sometimes the Router E200 hangs up, also with the LAN connections. The E200 is connected to a sky-DSL Router and works fine when no additional access point is connected. In the web-Interface of the E2000 I cant setup any specific Guest-WLAN settings.
View 1 Replies
View Related
Jul 7, 2011
E2000 has the guest account feature. Not sure if all guests shares the same login credentials. I would like to have guests account use seperate logins. Is this feature available? Another thing, I read the manual and it is indicated that only up to 10 maximum guest acccounts is allowed. I am looking for more than 10 - kinda like a hotspot software.
I've been looking everywhere. I've seen hotspot system, ddwrt, chillspot, etc. But it's complicated as firmware needed to be flashed.
View 1 Replies
View Related
Feb 12, 2011
Is it true that if someone wants to connect to the Guest network and macfiltering is on this is not possible. Which makes the guest network basicly useless.
View 5 Replies
View Related
Jul 15, 2011
How do I find the guest logon password?
View 3 Replies
View Related
Dec 6, 2010
We have been unable to connect our PSPs to the new E2000, and after several hours we're ready to throw in the towel and go get a different router!The PSPs only see the "guest" connection when using the scan option, but cannot connect to it. Even after manually adding both the main and the guest info we are STILL unable to connect either of the PSPs We had an older router from your company which we had no issues connecting 6 desktops, a lappy, 2 psp, 2 ds, 2 xbox 360, and a Wii, as well as our smart phones. After this recent "upgrade" to the E2000 the PSPs CANNOT connect no matter what we do. It gives many different error messages.
View 9 Replies
View Related
Oct 30, 2011
How do I add a guest without the cisco connect software since they don't have upgrade for osx lion.
View 3 Replies
View Related
Jul 7, 2011
How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies
View Related
Feb 18, 2013
I just installed and started using my E3000. Love it so far but I have a question about the guest network. I did set one up with a network name and password. It does show up under available networks but as an unsecured one. How do I go about securing it?
View 2 Replies
View Related
Jul 30, 2011
Using Cisco Connest I set up a password for guest access. It will function for a time then suddenly become insecure. Sometimes it will function for a month, sometimes a week. I have to reset the Unit to factory defaults each time and began again.
View 3 Replies
View Related
Nov 3, 2010
I had a simple PPTP VPN server running behind my old DLink router. When I installed the E3000 the VPN clients could no longer connect. The port forwarding for PPTP is turned on and VPN passthrough is enabled. The PPTP server reported GRE47 checksum failed. The linksys chat tech was not beneficial. How to get a PPTP route to work?
View 5 Replies
View Related
Dec 30, 2012
I switched from comcast to att uverse. I was happy about the guest-access feature of E3000 when using the comcast, where I can directly connect my e3000 to the modem (basically you can see two network, one is XXX, the other is XXX-guest). However, the ATT uverse has a gateway that combines the modem and router together, in order to use my e3000 instead of the built-in router of the gateway, I have done a LAN-to-LAN connection and I can access internet without any problem. But in this case, I can not enable my guest-access feature. When I use Cisco Connect to set up e3000, it says "cannot connect to your router". how to set up the guess-access feature of e3000 when using ATT uverse.
View 3 Replies
View Related
Jan 20, 2012
I haven't found a way to rename the Guest account on my E3000 router. If my router is named HomeRouter the Guest account automatically gets the name HomeRouter-guest. I have disabled the router's SSID broadcast, but it still broadcasts the almost identical Guest account.
View 4 Replies
View Related
Jul 8, 2011
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies
View Related
Feb 9, 2013
I have an E3000 that I am just setting up.I have two issues:
1> I am replacing a WRT110. I had the old router set with a static IP address supplied by my ISP. I configured the E3000 with the same address and I cannot access the internet. Are there any tricks to setting this up on an E3000?
2> As configured I there is a guest network setup. BUT when I access the router I don't see the tab to be able to configure it.
View 4 Replies
View Related
Feb 8, 2012
I have a wrt54g router and would like to separate the WLAN clients from accessing computers and servers on the LAN... in other words I would like to make it a "guest" network. I've put the router in "router" mode instead of "gateway". I just want to be sure if that is the best thing I can do in terms of turning the wireless network into an isolated one.
View 4 Replies
View Related
Sep 7, 2012
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies
View Related
Apr 12, 2011
For weeks guest access to my e3000 worked fine. Today I have a friend come over, his XP connects to the guest wi-fi, but his computer does not get a prompt for a password.
View 6 Replies
View Related
Apr 6, 2010
I just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
View 9 Replies
View Related
Aug 11, 2011
I have an E3000 with firmware version 1.0.04 with WiFi configured as:Guest5GHz (only N)2.4 GHz (only G)I use the guest network access for my guests or my neighbor.Usually they connect and the first page they see in the browser is the http://192.168.33.1/login.asp were they put the password. Some times shomething don’t work and the browser don’t show the page, so the people can’t use the connection because they get a timeout error.The only solution I have in this case is to resart the router, but sometimes is not enough and I have to fisically shotdown and restart it.The login.asp page starts with: This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc. the contents of this file may not be disclosed to third parties, copied or duplicated in any form without the prior written permission of CyberTAN Inc. This software should be used as a reference only, and it not intended for production use! What about a firmware update to fix it and give the control from the web administration over the guest network?
View 5 Replies
View Related
Jul 3, 2012
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
View 3 Replies
View Related
Apr 21, 2012
I have a Linksys E2000 router that is connected to my cable modem. I have a desktop computer that is connected to the router via an ethernet cable, and two laptops in the house that connect wirelessly to the router to get internet access.
This morning, all devices were connected to the internet just fine. I stepped away for a few hours and during that time the desktop 'lost' its internet connection. I have tried re-booting the router and removing-reconnecting the ethernet cable but nothing is restoring the connection.
The fact that my wireless devices are connecting means my internet service is fine, right? So what is preventing the desktop from gaining a connection?
View 1 Replies
View Related
Jan 11, 2011
Just replaced my older Cisco router with an E2000 and now none of the connected PCs can ping each other. I have two wired and two wireless nodes on the 192.168.1.X subnet (defaults) using DHCP. All nodes can access the Internet with no problems, but none of them can see each other -- no ping, no Network Neighborhood, nothing. Since this all worked fine before I swapped routers and I've made no changes on any of the nodes, I presume this is something about the router.
I've tried all the usual troubleshooting steps (spent 10 years working as Systems Engineering in IP networking) - no luck. I've also tried various settings of the router (e.g. turned off SPI) but no luck either.
my new router doesn't block connections between attached PCs on the same subnet ....
P.S. One strange observation : using Wireshark I can see the pinging node (.137) ARP for the destination IP (.102), and the ARP reply is sent by the destination node (.102) , but it looks like the Echo Request never makes it to the target machine -- i.e. I think the router is blocking it.
View 9 Replies
View Related
Sep 7, 2011
i have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies
View Related
Apr 3, 2012
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies
View Related
Aug 11, 2011
I have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies
View Related
Apr 21, 2011
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies
View Related
Jul 16, 2011
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies
View Related
