I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 RepliesI have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happened 3 times that my complete LAN disconnected for no reason. I didn't have any wired or wireless connection
View 9 Replies View RelatedWhy is the 2700 faster if the 3500 is more expensive ? 2. will cisco put out a firmware that allows me to block more then 100 urls and keywords cuz as it is now i find that limiting it to only 8 urls makes the new linksys routers useless and NO i wont use opendns they are slow and charge you to remove the ads thats why i use the keyword blockin to block popups and ads 3.will a firmware upgrade make the 3500 faster then the 2700 later on ?
View 4 Replies View RelatedI'm not entirely sure what's going on. I run 4 computers on this network, 2 Windows Xp, 1 Windows 7, and 1 Linux. All of which cannot access AIM, Gchat, and Minecraft(lol). I have no idea what would cause this, I run DD-WRT on my router(Linksys WRT-54G). I've checked all ports and I don't have anything blocked. I seriously need to fix this because I use AIM for my work. I can't even get into AIM Express which is web-based(tells me to check my network connection.
View 3 Replies View RelatedNew E3200 router (a few weeks old).
Using the manual settings under Status/Router and clicking the Disconnect button (by Login Status), the page reloads, and say I am disconnected.
Without any input from me, about 30 seconds later the page reloads and say I am connected.
Clicking disconnect, closing the tab and testing my connection proves that I'm not actually being disconnected at all. I cannot force this router to manually disconnect.
Is this a firmware bug or is there another setting else where that prevents me from manually shutting down my connection?
Edit: Firmware 1.0.04 build 1 Apr 10, 2012
Recently lost the setup for my newly installed ea6500 for no apparent reason. had to restart from the ground.I have the latest upgrade but wonder about the differences between the linksys coonect to the online version vs stand along versions. DO nor like expensive software that losses its setup for no good reason.I also irritated that I am unable to access my cable box. I own it and cable box and lynkiys has no right to block me from it. 192.168.100.1. I was able to accessed it with my Belkin router and I should be able to access with this expensive ea6500 box!!
We NEED a non-gui version. The gui is great for simple networks and people who do not want to know anything about their network. it's ment to be use to deliver additional services to us at a cost. duplicated or generates random users with ip or mac addresses complicating the parental control.
I'm tired of posting again and again, internet drops for about 20 or more mins, and can't get it back via reset, release & renew ip, system reboot.
View 1 Replies View RelatedI have two routers, a Telkom Mega 100WR and a Belkin F6D4630-4 v2. First I used the Mega 100WR and it randomly disconnected, then Belkin (which is new) and that too randomly disconnected. The funny thing is, both of them use to work.
View 1 Replies View RelatedI have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.
View 2 Replies View RelatedI will be working from home half the time and am trying to get set up. So here it goes:
Took PC #1 home and hooked everything up. Could access Internet.Had to bring PC #2 home because #1 didn’t have the programs I needed.Hooked #2 up, no internet access.Tried different network cable – no access.Tried different router port – no access. (router port light doesn’t illuminate, neither does port on PC)My personal PC that uses the same router has internet access.Hooked #1 back up as a test – could access internet.Hooked up #2 again, did a Run, cmd, ipconfig and got “media disconnected”I brought #2 back in for a PC tech to look at. He hooked it up in his office, had internet access.Took it back home and hooked everything up.The port lights illuminated on startup; but after it got to the desktop, lights are off.Tried ipconfig again, "media disconnected”. IP address doesn’t display.
All the while I have internet access on my own PC, plus when I hook up #1 to the same port using the same cable, I have internet access, which led me to believe it's something wrong with PC #2.Tech is saying it’s a problem with my router (Cisco E2500), which I restarted too.
I want to share PC internet (PPPOE connection) on my linksys wireless router (E3000)Problem : When i directly connect internet wire in router, pppoe connection frequently gets disconnected. So what i wanted was to share my pc internet on router.I have two lan card on windows 7 installed PC, 1st lan card is connected to internet cable and i can access internet on pc, second lancard is connected to wireless router. So basically what i want is to share pc internet ( PPPOE ) on wireless router through DHCP connection type.
View 1 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies View RelatedFor Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies View RelatedIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
I have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies View RelatedFor some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies View RelatedI got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies View RelatedI want to set up another wireless laptop to access my e2000 but i dont remember the network key, How can I retirieve the key? through cisco connect maybe?
View 1 Replies View RelatedE2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
View 8 Replies View RelatedI have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
View 3 Replies View Related