Linksys Wireless Router :: E2500 - No Internet Access For 2nd PC / Media Disconnected
Apr 16, 2013
I will be working from home half the time and am trying to get set up. So here it goes:
Took PC #1 home and hooked everything up. Could access Internet.Had to bring PC #2 home because #1 didn’t have the programs I needed.Hooked #2 up, no internet access.Tried different network cable – no access.Tried different router port – no access. (router port light doesn’t illuminate, neither does port on PC)My personal PC that uses the same router has internet access.Hooked #1 back up as a test – could access internet.Hooked up #2 again, did a Run, cmd, ipconfig and got “media disconnected”I brought #2 back in for a PC tech to look at. He hooked it up in his office, had internet access.Took it back home and hooked everything up.The port lights illuminated on startup; but after it got to the desktop, lights are off.Tried ipconfig again, "media disconnected”. IP address doesn’t display.
All the while I have internet access on my own PC, plus when I hook up #1 to the same port using the same cable, I have internet access, which led me to believe it's something wrong with PC #2.Tech is saying it’s a problem with my router (Cisco E2500), which I restarted too.
View 4 Replies
ADVERTISEMENT
Jan 22, 2012
Here is my setup.Using all MAC OSX I have AT&T DSL ISP connected to a (ISP provided) Speedstream 5100 Modem.I just purchased a Cisco Linksys 5200 N Router and I cannot access the internet. I followed the set-up instructions to the T but to no avail. I cannot find anything online about these two devices being incompatable. Do I purchase a new modem? If so how can I be sure it's compatible with the router?
View 1 Replies
View Related
Mar 1, 2013
I bought the router E2500 and I followed the steps for its configuration. It so happens that most of the time I turn on my router, it does not connect to microcomputer, because it loses the internet settings, requiring that I turn the CISCONNECT and after that, I have to turn off the microcomputer, wait for 2/3 minutes and then reconnect, for only then will be able to surf the internet. I notice that many times even I doing all this procedure the router does not give access to the internet. What should I do?
View 1 Replies
View Related
Feb 20, 2012
I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
View 4 Replies
View Related
Nov 14, 2012
Is there any way to use the e2500 without having hard wired internet access. I would like to use with my wii fii hot spot so that I could use my old printers that are not wireless enbled
View 1 Replies
View Related
May 26, 2011
I am seeing the following once I run the cmd.
Tunnel adapter Local Area Connection* 11
Media State . . . . . . Media disconnected
Connection-specific DNS Suffix
I cannot connect to the internet.
View 1 Replies
View Related
Oct 8, 2011
I have a US Robotics 5462 router and a D-Link DCM-202 cable modem on Comcast. I've had this router for years and initially configured it for wireless access using a Windows XP system (this router requires you to configure it via Ethernet and 192.168.2.1). That computer stopped working last year, so I got a new computer running Windows 7.When I first got this new PC, I could not connect to my router via Ethernet (just like I can't now), but I was still able to connect to the wireless network I had previously set up, so I was satisfied.
A year went by, and last week I was suddenly unable to access my wireless network, so I did a factory reset on the router, erasing my previously configured wireless network and requiring me to connect the router to my computer via Ethernet to reconfigure the router. I tried to do this, but despite all of the correct LEDs being lit on the router, I could not access 192.168.2.1. A little poking around on my control panel revealed that my LAN was being labeled as an "Unidentified Network" and there was "No Internet Access." I tried to make it a private network, but that didn't fix the issue.
I searched around for a while and read some advice to try running ipconfig. When I did that, I saw "Media Disconnected" for my LAN adapter. I've tried a few of the possible solutions already with no luck. With the same computer and the same Ethernet cable directly connected to my modem instead of through the router, I *CAN* get online. That's how I'm connected right now. Also, I have no problem accessing any wi-fi networks.
View 5 Replies
View Related
Apr 12, 2011
I was able to connect smoothly to any preferred connections in my area including my own. But now, it doesn't let me connect wirelessly to any of them. Now I typed ipconfig and this is what showed up.
Ethernet adapter Wireless Network Connection:
[code]...
View 3 Replies
View Related
Mar 11, 2011
i cant view my computer on my tv,or reverse, both connected to the hme network
View 3 Replies
View Related
May 29, 2012
I have searched so many threads concerning the problem I am having but have yet to find anything that works.On Sunday my husband changed our router. We have just moved from Sky to Talk Talk. Before the change, my wireless connection was absolutely fine.Now, everything else in the house is working on wireless fine (xBox, my smartphone, hubby's PC) except for my crappy Lenovo N 500 (XP SP3).Here is a copy/paste from my ipconfig /all:[CODE]
View 19 Replies
View Related
Jan 27, 2013
I have a fairly new Inpsiron 14z with windows 8 on it. Everything worked great out of the box, but all of a sudden my wireless stopped working. More specifically, it always says that the wifi is off, and pressing alt+f2 only cycles the bluetooth on and off, not doing anything about the wifi. Maybe I am just missing something stupid, I don't know. Here is my info:
Host Name: OS Name: Microsoft Windows 8OS Version: 6.2.9200 N/A Build 9200OS Manufacturer: Microsoft CorporationOS Configuration: Standalone WorkstationOS Build Type: Multiprocessor
[Code]......
View 7 Replies
View Related
May 25, 2011
I am trying to connect to my son's wireless internet with my own laptop. I can't get it to connect - I have tried to "renew IP address" and it doesn't work. I also got a message when I went to Start Run, etc etc "no operation can be performed on Wireless network while is has its media disconnected" I am able to connect to my own wireless internet at home on same laptop.
View 1 Replies
View Related
Aug 22, 2011
I'm trying to create an Ad-hoc network for use with my Android phone, however the phone does not discover the network.I've browsed various forums and tried a few things, but with no success.My laptop is able to detect other wireless networks. Wired Ethernet connection works fine.ipconfig /all results are below. The broadcom wireless LAN adapter shows Media Disconnected.I'm running Norton Internet Security and HP Wireless Assistant.
View 1 Replies
View Related
Aug 4, 2011
I'm tired of posting again and again, internet drops for about 20 or more mins, and can't get it back via reset, release & renew ip, system reboot.
View 1 Replies
View Related
Apr 18, 2012
I've enabled the Media Server on my E3000 router. My PS3 can see the server and play media from it by my PCs can't!
I'm using Windows Media Player v 12.0 on Windows 7 and some older version on Windows XP and it's my understanding that the Media Server should appear under the "Other Libraries" section but it does not.
Am I doing something wrong? Is there a bug in the E3000 firmware (I have the latest as of this date) or is the Media Server simply not compatible with Windows Media Player? compatible media player for Windows 7?
I did read a post about a firmware upgrade on the 4200 that broke the media player, but I don't know if such a problem exists for the E3000.
View 1 Replies
View Related
Dec 27, 2011
I have bought and installed an E2500 router 4 days ago. Installation of router and network using Cisco Connect was easy and without problems. However, after 4 days of usage, not changing anything in the network nor running Cisco Connect or accessing the web interface, I tried to start Cisco Connect and got the message "Cannot access your router".Internet is running, router is accessible via 192.168.1.1 in a browser window, Cisco Connect also works fine on my laptop.The only solution I found on this forum is: reset your router and reinstall Cisco Connect.and then every 4 days resetting my router and reinstalling the software?
View 4 Replies
View Related
Apr 21, 2012
I bought a new e2500 and it is working fine, all but port forwarding. This is not even close to my first router and I am advanced when it comes to setting these up. I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80. I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing. Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.
View 6 Replies
View Related
May 30, 2012
When I'm trying to access the Twonky setting page on http://192.168.1.1:9000/config I get: Access is restricted to MediaServer configuration! Is this normal or not?
View 2 Replies
View Related
Oct 23, 2011
I use to run Twonky media server on my iMac and I was very happy with it. Now I have purchased a Linksys Wifi Router E4200. Twonky server embedded works fine with all my devices except with my Samsung D8000 Led TV. In the Mac version I must identify manually the player (Samsung TV), if not mkv won't play. The question is: How can I select the device in the Linksys E4200? The config page is not available and displays "Access is restricted to mediaserver configuration" E4200 firm V. 1.0.03
View 9 Replies
View Related
May 17, 2011
I have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies
View Related
Oct 31, 2012
E2500 given to me cannot access password to setup
View 1 Replies
View Related
May 28, 2012
I have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
View 6 Replies
View Related
Dec 13, 2012
I have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?
View 2 Replies
View Related
Oct 13, 2012
I just purchased an E2500 wireless router. I put the Cisco Connect setup disc in and it could not find my router. With excellent Tech Support, I got it to work. I still do not have any Cisco Connect software on my PC to set passwords or preferences. If I try to run the disc again, it gives me a system critical error and shuts down my computer. How can I get software to access my router settings?
View 1 Replies
View Related
Mar 2, 2013
Since installing the E2500, I can no longer access YouTube videos on my wireless devices. Is this a setting that needs to be changed?
View 1 Replies
View Related
Nov 1, 2011
I did not use the CD to set up, and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking no problem. Only issue I have is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.
View 8 Replies
View Related
Dec 29, 2012
using a Linksys E2500. I have a Ubuntu "server" set up which i can access on my LAN through VNC Viewer (windows machines) no problem. I can even access it through the external IP address on a machine inside the LAN (both internal address and external address work from inside the LAN). I set up port forwarding (per portforward.com) but i still can not access my machine from outside the LAN. It has a static IP as well btw.
View 2 Replies
View Related
Jul 24, 2012
Is it possible with the E2500 (or some other device) to rebroadcast a wireless signal?Here's the situation, I live on a boat, I want to connect my laptop to a local wireless signal (which I pay for). I then want to connect my E2500 to the laptop via the "Internet" port on the E2500. This doesn't work? This would allow all my wireless devices to stay connected to a single connection point. When I move the boat and change the wireless connection, I only have to do it once for a single connection. Is there some way to achieve this?
View 1 Replies
View Related
Dec 19, 2012
I just bought this Cisco E2500 router last night. I was able to set new pass phrase and name (SSID). I then proceeded to add wireless computers to the router-no problem. had 1 computer I couldnt set up because the person was sleeping. So this morning I go to set up their computer, and found the name (SSID) on the available networks. I clicked on it, and it connected right away WITHOUT ASKING FOR THE PASSPHRASE!!!!! NO ONE put the pass phrase in this computer before. I checked the connection-and sure enough, there was the passphrase right there on this computer! So HOW did this computer, that I hadnt ever tried to connect to this new network before- suddenly get the passphrase as well? if anyone in this neighborhood can just connect to my network and automatically get the passphrase like that-then I need to take this back and get a refund!! That isnt secure at all!
View 1 Replies
View Related
May 1, 2012
I am running a wired and wireless home network..using a G 2.4 router and access point. I purchased an Linksys E2500 N 5Ghz wiresless router can I still effectively use my Linksys G 2.4 g access point? Will I still have to get a linksys N 5Ghz access point to properly obtain the most speed and security?
I use the wireless with a cable service and use wireless access only for the cell phones via WiFi.I rarely use the desktops on the home network, I want to increase the speed for the cell phone via Wi-fi, Currently speedtest results were 4.80 for downloads and 2.0 for uploads. I have not much use for uploading except for sending photos via wi-fi.
View 1 Replies
View Related
Aug 21, 2011
How to access the media server and/or external USB drive on an E4200 from an iPad?
View 1 Replies
View Related
May 2, 2012
I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
View 8 Replies
View Related
Dec 20, 2011
I got 5 E2500 routers and the main one has setup to IP address 192.168.1.254 and the rest APs are programmed into the bridge mode with the IP address 192.168.1.245 through 248. The secured wireless network works fine when I roaming between these APs but the only AP that I can get internet access for guest wireless network is the main (192.168.1.254) router; for every other APs, I will get the guest log on screen (prompt for guest access password) and no internet access after I type in the correct access password. Does the E2500 support multiple APs guest or it requires a special way to configure it?
View 5 Replies
View Related
