Linksys Wireless Router :: Way To Get Software To Access E2500 Settings

Oct 13, 2012

I just purchased an E2500 wireless router. I put the Cisco Connect setup disc in and it could not find my router. With excellent Tech Support, I got it to work. I still do not have any Cisco Connect software on my PC to set passwords or preferences. If I try to run the disc again, it gives me a system critical error and shuts down my computer. How can I get software to access my router settings?

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: Getting E2500 Advanced Settings?

Jan 14, 2012

A few months ago I purchased an e2500 Cisco Linksys router to use in my home.  This past Christmas, my family got about 4 new wifi devices which they added to the network bringing the total number of devices on my home network to 10.  I wanted to know if there are any advanced settings in Cisco Connect that I can tweak to make my wifi speeds faster because right now I'm getting about 55 Mbps on most of my devices.  I was also wondering what the typical range of the e2500 router was and if the e4200 offers a large improvement.  

View 3 Replies View Related

Linksys Wireless Router :: E2500 - Send Stronger Wifi Signal / Dns Settings

Dec 1, 2011

I just upgraded from a WRTG 54 version 2 wireless router to the Linsksys E2500. The reason for the change is to send a stronger wireless signal strength further in my house. Setup was easy to my laptop and XBox 360 but my Samsung Internet TV is another story. I can get my tv to get the wireless signal but when I click on an app nothing but error messages. Often times it will say to check my dns settings but I am not that tech savvy and don't know what to do.

View 9 Replies View Related

Linksys Wireless Router :: E2500 - Cannot Access It

Dec 27, 2011

I have bought and installed an E2500 router 4 days ago. Installation of router and network using Cisco Connect was easy and without problems. However, after 4 days of usage, not changing anything in the network nor running Cisco Connect or accessing the web interface, I tried to start Cisco Connect and got the message  "Cannot access your router".Internet is running, router is accessible via 192.168.1.1 in a browser window, Cisco Connect also works fine on my laptop.The only solution I found on this forum is: reset your router and reinstall Cisco Connect.and then every 4 days resetting my router and reinstalling the software?

View 4 Replies View Related

Linksys Wireless Router :: E2500 Will Not Allow Port 80 Access

Apr 21, 2012

I bought a new e2500 and it is working fine, all but port forwarding.  This is not even close to my first router and I am advanced when it comes to setting these up.  I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80.  I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing.  Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.

View 6 Replies View Related

Linksys Wireless Router :: E2500 As Wifi Access Point Only?

May 17, 2011

I have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?

View 9 Replies View Related

Linksys Wireless Router :: E2500 / Unable To Access Internet

Jan 22, 2012

Here is my setup.Using all MAC OSX I have AT&T DSL ISP connected to a (ISP provided) Speedstream 5100 Modem.I just purchased a Cisco Linksys 5200 N Router and I cannot access the internet. I followed the set-up instructions to the T but to no avail. I cannot find anything online about these two devices being incompatable.  Do I purchase a new modem? If so how can I be sure it's compatible with the router?

View 1 Replies View Related

Linksys Wireless Router :: E2500 Does Not Give Internet Access

Mar 1, 2013

I bought the router E2500 and I followed the steps for its configuration. It so happens that most of the time I turn on my router, it does not connect to microcomputer, because it loses the internet settings, requiring that I turn the CISCONNECT and after that, I have to turn off the microcomputer, wait for 2/3 minutes and then reconnect, for only then will be able to surf the internet. I notice that many times even I doing all this procedure the router does not give access to the internet. What should I do?

View 1 Replies View Related

Linksys Wireless Router :: E2500 - Cannot Access Password To Setup

Oct 31, 2012

E2500 given to me cannot access password to setup

View 1 Replies View Related

Linksys Wireless Router :: Access Restrictions On Current E2500?

May 28, 2012

I have an old WRT54G and the access restrictions really don't work.  it's sloppy and ineffective.
 
i'm thinking about upgrading... perhaps to the E2500.  Do the access restrictions now work properly?  Am I able to allow access to a specific site only during certain times?
 
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?

View 6 Replies View Related

Linksys Wireless Router :: Using E2500 Wifi Access Point?

Dec 13, 2012

I have an existing home network with a D-link wireless router, IP 192.168.0.1.  In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100.  Used the same SSID and passwords, worked flawlessly.  Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1.  I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1.  I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP.  With my previous router, this worked easily and flawlessly.
 
1. What am I doing wrong (ok, other than using Dlink components)?

2. Should these two different brand components work ok together llike this or is that a problem?

3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?

View 2 Replies View Related

Linksys Wireless Router :: E2500 - Can't Access YouTube Videos On It

Mar 2, 2013

Since installing the E2500, I can no longer access YouTube videos on my wireless devices.  Is this a setting that needs to be changed?

View 1 Replies View Related

Linksys Wireless Router :: Guest Access On E2500 Not Working

Nov 1, 2011

I  did not use the CD to set up,  and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking  no problem. Only  issue I have  is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.

View 8 Replies View Related

Linksys Wireless Router :: E2500 - Vnc Viewer External Access?

Dec 29, 2012

using a Linksys E2500.  I have a Ubuntu "server" set up which i can access on my LAN through VNC Viewer (windows machines) no problem.  I can even access it through the external IP address on a machine inside the LAN (both internal address and external address work from inside the LAN).  I set up port forwarding (per portforward.com) but i still can not access my machine from outside the LAN.  It has a static IP as well btw.

View 2 Replies View Related

Linksys Wireless Router :: Using E2500 As Access Point From Another Wi-Fi Device?

Jul 24, 2012

Is it possible with the E2500 (or some other device) to rebroadcast a wireless signal?Here's the situation, I live on a boat, I want to connect my laptop to a local wireless signal (which I pay for). I then want to connect my E2500 to the laptop via the "Internet" port on the E2500. This doesn't work? This would allow all my wireless devices to stay connected to a single connection point. When I move the boat and change the wireless connection, I only have to do it once for a single connection. Is there some way to achieve this?

View 1 Replies View Related

Linksys Wireless Router :: E2500 Already Had Access Phrase In Computer?

Dec 19, 2012

I just bought this Cisco E2500 router last night. I was able to set new pass phrase and name (SSID). I then proceeded to add wireless computers to the router-no problem. had 1 computer I couldnt set up because the person was sleeping. So this morning I go to set up their computer, and found the name (SSID) on the available networks. I clicked on it, and it connected right away WITHOUT ASKING FOR THE PASSPHRASE!!!!! NO ONE put the pass phrase in this computer before. I checked the connection-and sure enough, there was the passphrase right there on this computer! So HOW did this computer, that I hadnt ever tried to connect to this new network before- suddenly get the passphrase as well? if anyone in this neighborhood can just connect to my network and automatically get the passphrase like that-then I need to take this back and get a refund!! That isnt secure at all!

View 1 Replies View Related

Linksys Wireless Router :: E2500 Effectively Use G2.4 G Access Point

May 1, 2012

I am running a wired and wireless home network..using a G 2.4 router and access point. I purchased an Linksys E2500 N 5Ghz wiresless router can I still effectively use my Linksys G 2.4 g access point? Will I still have to get a linksys N 5Ghz access point to properly obtain the most speed and security?

I use the wireless with a cable service and use wireless access only for the cell phones via WiFi.I rarely use the desktops on the home network, I want to increase the speed for the cell phone via Wi-fi, Currently speedtest results were 4.80 for downloads and 2.0 for uploads. I have not much use for uploading except for sending photos via wi-fi.

View 1 Replies View Related

Linksys Wireless Router :: E2500 - No Internet Access For 2nd PC / Media Disconnected

Apr 16, 2013

I will be working from home half the time and am trying to get set up. So here it goes:
 
Took PC #1 home and hooked everything up. Could access Internet.Had to bring PC #2 home because #1 didn’t have the programs I needed.Hooked #2 up, no internet access.Tried different network cable – no access.Tried different router port – no access. (router port light doesn’t illuminate, neither does port on PC)My personal PC that uses the same router has internet access.Hooked #1 back up as a test – could access internet.Hooked up #2 again, did a Run, cmd, ipconfig and got “media disconnected”I brought #2 back in for a PC tech to look at. He hooked it up in his office, had internet access.Took it back home and hooked everything up.The port lights illuminated on startup; but after it got to the desktop, lights are off.Tried ipconfig again, "media disconnected”. IP address doesn’t display.
 
All the while I have internet access on my own PC, plus when I hook up #1 to the same port using the same cable, I have internet access, which led me to believe it's something wrong with PC #2.Tech is saying it’s a problem with my router (Cisco E2500), which I restarted too.

View 4 Replies View Related

Linksys Wireless Router :: E2500 As Access Point In Office Network?

May 2, 2012

I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?

View 8 Replies View Related

Linksys Wireless Router :: E2500 May Support Multiple APs For Guest Access?

Dec 20, 2011

I got 5 E2500 routers and the main one has setup to IP address 192.168.1.254 and the rest APs are programmed into the bridge mode with the IP address 192.168.1.245 through 248. The secured wireless network  works fine when I roaming between these APs but the only AP that I can get internet access for guest wireless network is the main (192.168.1.254) router; for every other APs, I will get the guest log on screen (prompt for guest access password) and no internet access after I type in the correct access password. Does the E2500 support multiple APs guest or it requires a special way to configure it?

View 5 Replies View Related

Linksys Wireless Router :: Use The E2500 Without Having Hard Wired Internet Access?

Nov 14, 2012

Is there any way to use the e2500 without having hard wired internet access.  I would like to use with my wii fii hot spot so that I could use my old printers that are not wireless enbled

View 1 Replies View Related

Linksys Wireless Router :: E2500 As An Additional Access Point Will Not Connect

Oct 16, 2012

I have AT&T Uverse which provides Internet for my home.  The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office.  The solution was to buy a Cisco E2500 and add it as an access point upstairs.
 
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs.  DHCP is turned off on the E2500.  I have my office PC wired into the E2500.  The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds.  The problem comes with my wireless devices trying to connect to the E2500. 
 
I should mention that yesterday when i bought this, all worked fine.  This morning when I came into my office none of the wireless devices would connect to the E2500 at all.   But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
 
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?

View 8 Replies View Related

Linksys Wireless Router :: Local Management For E2500 As Wifi Access Point

Jul 19, 2012

I am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?

View 2 Replies View Related

Linksys Wireless Router :: E4200 / E3200 Or E2500 Better For Home Access Point?

Jan 18, 2012

I am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?

View 9 Replies View Related

Linksys Wireless Router :: Wrt54gs V7.2 - Can't Access Settings

Jul 8, 2011

I changed the router's IP to 192.168.2.1 due to the same situation as this [URL] linksys and now I can't access my settings I have tried the both pips and nothing and I can't seem to get my linksys wrt54gs v7.2 to let two computers be on the internet at the same time both can be on the network but on one on the internet

View 6 Replies View Related

Linksys Wireless Router :: E2500 - Eliminate Guest Login Screen From Being Displayed / Required To Access

Nov 11, 2012

is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.

View 4 Replies View Related

Linksys Wireless Router :: Wrt120n Unable To Access Settings Page

Jan 6, 2012

Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".

View 2 Replies View Related

Linksys Wireless Router :: Access EA6500 Settings To Setup Security?

Dec 31, 2012

just set up my EA6500 in bridge mode, i have the Ethernet cable plugged into the EA6500's yellow WAN port, is that correct, Cisco Article ID: 24583 is not that clear, Cannot also seem to access the EA6500's settings to setup security?

View 2 Replies View Related

Linksys Wireless Router :: WRT610N No Access To Edit Any Settings On The QOS Page

Mar 11, 2012

I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);

Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.

View 1 Replies View Related

Linksys Wireless Router :: E1000 - Can't Access Router Settings After Changing To Static IP

Jun 26, 2012

I installed an IP camera, and had to change my E1000 router settings to a static IP address.  Now I can't access the router settings.  192.168.1.1 is still the default gateway, but it won't open in any browser.
 
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place.  I'm not very good at this stuff, and it's a small miracle that I did it once.  

View 4 Replies View Related

Linksys Wireless Router :: WRT610N V1 Flashing Power Light / No Wireless / Can't Access Settings

Apr 28, 2012

Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
 
Currently I am wired through it with my desktop and its working, but not much else.

View 3 Replies View Related

Linksys E2500 Router - How To Change Network Access

Oct 20, 2012

Just installed Linksys E2500 router connected to my Desktop and Cable Modem and access the internet fine. My kindle accesses it and the internet fine. My laptop running Vista connects nicely but only has local access. I find the network and connection area where it sees a network with local only access. I have no clue how to go about changing that. I have the correct password because my Kindle asked me. My laptop does not ask for the password.

View 3 Replies View Related

Linksys Wired Router :: E2500 - Cannot Remotely Access Zoneminder On Port 80

Jan 4, 2012

I have a Cisco Linksys E2500 modem and I cannot access Zoneminder which is essentially a Linux Security video DVR software package.  It is running on a Ubuntu Linux server. 
 
I have HTTP port 80 forwarded to the the static IP address of the Ubuntu server but I repeatedly get a error indicating that the connection timed out whenever I try to access Zoneminder remotely as in remotely accessing it from a coffee shop.
 
I have absolutely no problem accessing Zoneminder when I on my home local LAN.
 
I can access other software from remote locations on port 4369 with a TCP preferred protocol setting.  That is, port 4369 is forwarded to another Windows workstation with an assigned static IP address. Absolutely no problems with port forwarding of 4369.
 
Also,  I've tested port 80 on the YouGetSignal website which is used for testing port forwarding.  The website indicates that port 80 is closed.  But when I test port 4369, the website reports that the port is open.  Zoneminder which uses port 80 is fully operational when I test port 80 via YouGetsignal.
 
My ISP has told me that they do not block any ports including port 80. 

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved