is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.
View 4 RepliesI did not use the CD to set up, and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking no problem. Only issue I have is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.
View 8 Replies View RelatedI got 5 E2500 routers and the main one has setup to IP address 192.168.1.254 and the rest APs are programmed into the bridge mode with the IP address 192.168.1.245 through 248. The secured wireless network works fine when I roaming between these APs but the only AP that I can get internet access for guest wireless network is the main (192.168.1.254) router; for every other APs, I will get the guest log on screen (prompt for guest access password) and no internet access after I type in the correct access password. Does the E2500 support multiple APs guest or it requires a special way to configure it?
View 5 Replies View RelatedAfter popping in the installation CD, the screen says hook everything up, which I do. Then click next, where it says "Searching Networks", then quickly changes to "Connecting to Network", and then it says it "Cannot Find Router.". Err. Check setup, etc.If I hook up directly to new router VIA internet cable. Also, this is strange: When I just open up a web browser and try to log into the router 192.168.1.1, using no user name, administration as the password, it won't let me in to the router. Even after I have reset the router with a pen.
View 1 Replies View RelatedI tried to log in into my EA4500 today, and instead of the simple window that asks for the user name and password, I am getting a Cisco Connect Cloud log in screen. It is very strange.
At the top it says: Cisco Connect Cloud/Powering Linksys Products
and below that:
Sign In If you have not yet created an account, click the 'Create Account' button in the upper right corner of the page
There is a help button, a button to create an account. There is a place where I can enter an email address and a password.
Pressing the Help button I learned that I can probably bypass this silly screen by disconnecting the internet. Is there a better way to bypass this screen and turn off Cisco Connect Cloud?
I have the Clear Hub Express (Router/Modem combined) and I am trying to connect a separate Belkin Wireless Router (Model F5D8233-4v1) to allow additional "hard wire" connections. Correct settings required for the Clear Hub Express and any additional information that can instruct me on how to access the Belkin set-up screen if required. The standard 192.168.2.1 is not allowoing access to the Belkin Router.
View 1 Replies View RelatedCannot connect to Linksys Router 192.168.1.1 Webpage, do not get login setup screen.
View 1 Replies View RelatedWhen setting up our router for Wifi, we made an account which is locked, but accidentally made one for guests which is not locked. How can we eliminate the guest account?
View 3 Replies View RelatedIs it possible to change the look of welcome page (guest login) to change so that it is personal. Of course it would be great if the guests have to log on your personal page.On this page you would be able to indicate the rules and and limitations. It would also be a good option for certain that your guests a limited time duration for the connection and gives max download. This would also be found to be in a log.
View 2 Replies View Relatedi just bought a netgear router. i was able get into routers login screen once. thought every thing is good? everything looked correct? now i cant get into login screen at all again. im confused it should be easy. either use 192.168.1.1 or 192.168.1.2 or 192.168.0.1 and 192.168.1.254. i tried them all with no luck.
View 3 Replies View RelatedI currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
View 6 Replies View RelatedI recently purchased the E2500 cisco router. How does the MAC computer be able to log in as Guest user to access internet?
View 2 Replies View RelatedI have a Linksys E2500 router. Is it possible to have one network name for the secured network and a different network name for the Guest network? The thought is to not have the SSID of the secured network broadcast while allowing the SSID of the Guest network to be broadcast. With the convention of simply adding "Guest" to the end of the SSID for the secured network, it defeats the security option of not having the SSID of the secured network broadcast.
View 1 Replies View RelatedWhen Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies View RelatedI have a Cisco network at my office and the router and everything is set up under my desk.I can use the internet just fine on my office computer but I am trying to use it on my laptop and login to the guest account .I ran across the Cisco Connect sofware and that I need it to find the password but the problem is I dont think I have a router or whatever it is that is compatible with this software I am using WRT54g wireless n router, the models on the site for the cisco connect are e series
View 1 Replies View RelatedConfig:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
I have an E3000 with firmware version 1.0.04 with WiFi configured as:Guest5GHz (only N)2.4 GHz (only G)I use the guest network access for my guests or my neighbor.Usually they connect and the first page they see in the browser is the http://192.168.33.1/login.asp were they put the password. Some times shomething don’t work and the browser don’t show the page, so the people can’t use the connection because they get a timeout error.The only solution I have in this case is to resart the router, but sometimes is not enough and I have to fisically shotdown and restart it.The login.asp page starts with: This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc. the contents of this file may not be disclosed to third parties, copied or duplicated in any form without the prior written permission of CyberTAN Inc. This software should be used as a reference only, and it not intended for production use! What about a firmware update to fix it and give the control from the web administration over the guest network?
View 5 Replies View RelatedThe problem i am experiencing is that on my home network i have been using for several years now one computer on my network suddenly cannot get online..however it can connect. They determined that all is working well and all settings are as they should be. I then contacted my ISP, Cox communications and was essentially told the same thing. This is after going through several tests with each, such as ping tests, turning the gateway off/on, reviewing settings such as TCP/IP, DNS, etc, etc. The findings were that i have IP addresses and everything else that should be there. Ive turned off the firewall, disabled antivirus, reset tcp/ip stack and winsock. I have been working on this for two days and after paying for it still do not have it fixed. The computer acts as it normally does, no other problems except that when i press the IE icon to open a browser window it tries to go to my homepage, google, but then reverts to the "page cannot be displayed screen". This computer is running XP SP2 and is a wired connection(although it was wireless when i first experienced the problem because i have a network adapter installed as well..but i disabled it and enabled my LAC and used the ethernet cable because this is one of the exercises cisco ahd me perform to see if i could connect wired/wirelessly.. better bandwidth anyway at 100mbps compared to the 56mbps with the wireless-g adapter). The othe computer is a laptop running windows 7.
View 16 Replies View RelatedI have 4 PCs connected to a wireless modem router(WBR 6601).All 4PCs are configured to shared all folder in C drive. These PCs are not configure to use domain.The thing is whenever I let my guest to connect to my wireless modem router for internet usage. They will be able to see all of my shared Folder(4 PCs) under the network Terminals.Is there anyway i can restrict the guest from accessing/seeing my shared folder and allow them to connect to my WAP to use for internet browsing only ?
[code]....
I have 4 PCs connected to a wireless modem router(WBR 6601). All 4PCs are configured to shared all folder in C drive. These PCs are not configure to use domain.The thing is whenever I let my guest to connect to my wireless modem router for internet usage. They will be able to see all of my shared Folder(4 PCs) under the network Terminals.Is there anyway i can restrict the guest from accessing/seeing my shared folder and allow them to connect to my WAP to use for internet browsing only ? :scratch:
My equipment :scratch::-
PC #1 - Acer M1830(Windows 7 Home Premium)
PC #2 - Acer M1900(Windows 7 Home Premium)
PC #3 - DELL Vostro(Windows XP Pro)
PC #4 - DELL Inspiron(Windows XP Pro)
Level 1 WBR 6601 Wireless/Modem Router
If there are no configuration can be done is there any hardware tools that have this restricting feature ?
I go into my login page and all I see is blank. Just a white screeb. I have put in my IP address, I have no idea what I should do. I have been trying to fnd my password but the page has no login.
View 3 Replies View Relatedhow i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies View RelatedI have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
View 8 Replies View RelatedI'm having some issues with Web-Passthrough, I'm using two 4404-50 controllers. Clients get IP addresses well. I'm using the controllers internal DHCP Servers. Controllers can reach DNS public IP Addresses (from management and guest vlan), the issue is that only very few clients are able to get displayed the Web-Passthrough page, the rest of the clients never get the page.
Version 7.0.98.0
The controllers also work as anchor controllers for two more foreign controllers.
I have bought and installed an E2500 router 4 days ago. Installation of router and network using Cisco Connect was easy and without problems. However, after 4 days of usage, not changing anything in the network nor running Cisco Connect or accessing the web interface, I tried to start Cisco Connect and got the message "Cannot access your router".Internet is running, router is accessible via 192.168.1.1 in a browser window, Cisco Connect also works fine on my laptop.The only solution I found on this forum is: reset your router and reinstall Cisco Connect.and then every 4 days resetting my router and reinstalling the software?
View 4 Replies View RelatedI bought a new e2500 and it is working fine, all but port forwarding. This is not even close to my first router and I am advanced when it comes to setting these up. I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80. I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing. Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.
View 6 Replies View RelatedI have my working computer and laptop which use my Cisco wireless. Recently I got a tablet samsumg galaxy tap 2 GT-P5113. The Andriod Version 4.0.4?
View 1 Replies View RelatedI have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies View RelatedHere is my setup.Using all MAC OSX I have AT&T DSL ISP connected to a (ISP provided) Speedstream 5100 Modem.I just purchased a Cisco Linksys 5200 N Router and I cannot access the internet. I followed the set-up instructions to the T but to no avail. I cannot find anything online about these two devices being incompatable. Do I purchase a new modem? If so how can I be sure it's compatible with the router?
View 1 Replies View RelatedI bought the router E2500 and I followed the steps for its configuration. It so happens that most of the time I turn on my router, it does not connect to microcomputer, because it loses the internet settings, requiring that I turn the CISCONNECT and after that, I have to turn off the microcomputer, wait for 2/3 minutes and then reconnect, for only then will be able to surf the internet. I notice that many times even I doing all this procedure the router does not give access to the internet. What should I do?
View 1 Replies View RelatedE2500 given to me cannot access password to setup
View 1 Replies View RelatedI have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
I have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?