Linksys Wireless Router :: Changing Look Of Welcome Page (guest Login)
Feb 9, 2013
Is it possible to change the look of welcome page (guest login) to change so that it is personal. Of course it would be great if the guests have to log on your personal page.On this page you would be able to indicate the rules and and limitations. It would also be a good option for certain that your guests a limited time duration for the connection and gives max download. This would also be found to be in a log.
View 2 Replies
ADVERTISEMENT
Jun 11, 2011
When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies
View Related
Jan 25, 2011
Config:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
View 9 Replies
View Related
Aug 11, 2011
I have an E3000 with firmware version 1.0.04 with WiFi configured as:Guest5GHz (only N)2.4 GHz (only G)I use the guest network access for my guests or my neighbor.Usually they connect and the first page they see in the browser is the http://192.168.33.1/login.asp were they put the password. Some times shomething don’t work and the browser don’t show the page, so the people can’t use the connection because they get a timeout error.The only solution I have in this case is to resart the router, but sometimes is not enough and I have to fisically shotdown and restart it.The login.asp page starts with: This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc. the contents of this file may not be disclosed to third parties, copied or duplicated in any form without the prior written permission of CyberTAN Inc. This software should be used as a reference only, and it not intended for production use! What about a firmware update to fix it and give the control from the web administration over the guest network?
View 5 Replies
View Related
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Mar 23, 2012
I tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.
View 1 Replies
View Related
Feb 3, 2013
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies
View Related
Jul 13, 2012
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies
View Related
Mar 29, 2013
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
View 6 Replies
View Related
Oct 30, 2012
I have a Cisco network at my office and the router and everything is set up under my desk.I can use the internet just fine on my office computer but I am trying to use it on my laptop and login to the guest account .I ran across the Cisco Connect sofware and that I need it to find the password but the problem is I dont think I have a router or whatever it is that is compatible with this software I am using WRT54g wireless n router, the models on the site for the cisco connect are e series
View 1 Replies
View Related
Nov 11, 2012
is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.
View 4 Replies
View Related
Apr 28, 2013
Region : UnitedKingdom
Model : TD-W8961ND
Hardware Version : Not Clear
Firmware Version : V.3
ISP : ADSL24
Using windows 7 and 8 on different machines I am unable access my routers web based set up.
I enter the usual "admin" and password in the login box. 3 goes and then get error message. or hangs on waiting.(connected to the router with Ethernet Cable). Could this be a windows based problem. I think it was ok on XP but that is gone now. Router is working fine but I just cant access it to alter any settings.
My 2 other spare routers which are not TP-link also have the same problem.
View 1 Replies
View Related
Aug 29, 2012
i want to stablish a new internet connection through bsnl broad band tell me hou i can install and run internet.
View 1 Replies
View Related
Feb 10, 2012
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
View 19 Replies
View Related
Jun 6, 2012
I go into my login page and all I see is blank. Just a white screeb. I have put in my IP address, I have no idea what I should do. I have been trying to fnd my password but the page has no login.
View 3 Replies
View Related
Feb 14, 2012
We set up our new Linksys last night but when the password was written down there is no distinction between upper and lower case letters - I can't login to an account page or do anything and I needed a password for a visiting friend.
View 1 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Feb 4, 2013
Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect
Things that I have already tried:
- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.
- Tried with different browsers.
- Tried with seperate computer with different OS's (Mac and PC)
- Unable to flush dns because I get this error: CMD prompt error message .
- Have factory reset router a few times now.
- Unplugged, left off for 20mins-2hours.
View 16 Replies
View Related
Jul 12, 2012
I have just bought a Belkin n150 router. Connected it to my modem and PC and I'm recieving internet. Connected my phone and laptop and getting wireless.The issue, however, is that I cannot login to the router page. The login says to leave blank for default, but it gives me an incorrect password error. I have tried resetting using the button located above the power cable to go back to defaults, but I continue to recieve the error.
I have tried a all the other usual default passwords, password, administrator, admin, etc.I've gone through pages of google search results and found nothing. Have I missed something obvious or did Walmart sell me a defective router?
View 1 Replies
View Related
Jan 31, 2013
Whenever I enter 192.168.1.1 to access the login page of my router, I cant access it to configure it even after resetting it !I also tried changing TCP/IP settings to static as mentioned in the router's manual but it dint work?
View 4 Replies
View Related
Feb 21, 2012
I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.
I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.
The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.
View 6 Replies
View Related
Oct 17, 2012
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies
View Related
Feb 25, 2011
I was in a pub the other day. When I tried to use their wireless I was directed to a webpage to enter the password.I am a web designer and want to make a funky login page, not for a user ID. Just to enter the password to my wireless.How do I do this? Im not aiming to make my system more secure.
View 1 Replies
View Related
Oct 8, 2012
I am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies
View Related
Apr 7, 2012
I been using my mechanics Wifi connection with my internal wireless adapter for at least 6 months. Living next door he has a guest Wifi connection for his customers that requires a password. I only had to use the password once and since then it has automatically connected. I recently purchased a usb wirless adapter with an antenna to get a better signal and it connects to the server but the login access page will not display nor will it connect to the internet. With this I get error 102.
View 4 Replies
View Related
Jan 16, 2011
I have 4 PCs connected to a wireless modem router(WBR 6601).All 4PCs are configured to shared all folder in C drive. These PCs are not configure to use domain.The thing is whenever I let my guest to connect to my wireless modem router for internet usage. They will be able to see all of my shared Folder(4 PCs) under the network Terminals.Is there anyway i can restrict the guest from accessing/seeing my shared folder and allow them to connect to my WAP to use for internet browsing only ?
[code]....
View 9 Replies
View Related
Jun 5, 2012
Where do you turn this option off? i have looked under security and did not see any thing.
View 1 Replies
View Related
Jan 17, 2011
I have 4 PCs connected to a wireless modem router(WBR 6601). All 4PCs are configured to shared all folder in C drive. These PCs are not configure to use domain.The thing is whenever I let my guest to connect to my wireless modem router for internet usage. They will be able to see all of my shared Folder(4 PCs) under the network Terminals.Is there anyway i can restrict the guest from accessing/seeing my shared folder and allow them to connect to my WAP to use for internet browsing only ? :scratch:
My equipment :scratch::-
PC #1 - Acer M1830(Windows 7 Home Premium)
PC #2 - Acer M1900(Windows 7 Home Premium)
PC #3 - DELL Vostro(Windows XP Pro)
PC #4 - DELL Inspiron(Windows XP Pro)
Level 1 WBR 6601 Wireless/Modem Router
If there are no configuration can be done is there any hardware tools that have this restricting feature ?
View 11 Replies
View Related
Jul 4, 2011
To enable our receptionits to print a guest user ticket on a small A8 ticket printer I'm looking for a way to adjust the layout and formatting of the guest account credentials page.
I have searched through the javascript and css files but with no success.
We are using WCS 7.0.172.0
View 3 Replies
View Related
Aug 1, 2012
I've been asked to create 2 wireless networks for guest access. They are to be used by clients of 2 different companies and they have asked for the website of each company to automatically open as a landing page. e.g.
-WLAN1 - password is companyname1 - landing page = www.companyname1.com
-WLAN2 - password is companyname2 - landing page = www.companyname2.com
Is this possible with our 5508 WLC? I have googled it and can see that you can set a web auth page but I need different landing pages depending on which WLAN is connected to.
View 11 Replies
View Related
Feb 19, 2012
I have a 5508 WLC running 6.0.202.0. It functions as the Anchor Controller for the guest network. It sits in our Internet DMZ and is isolated from the rest of the network. It does not connect to AD, ACS, etc. The guest wireless WLAN is configured for Web Policy - Authentication. I have a customized login page. Credential management is done by WCS.
Users are connecting to the guest wireless network and entering their creds with no issues using mobile devices (iPad, etc). Then the mobile device goes to sleep / turns off and when they go to use it again, they have to type their creds in again. They dont like retyping their creds throughout the day.
good way mitigate the multiple logins? Something like a 'save password' option on the customized page?
View 5 Replies
View Related
Feb 10, 2013
I want to setup a webpage for my guest network (no authentication) users. When the client connects to the open guest network and upon opening a browser they would be directed to a survey that I would like them to take, if they don't want to take it they can begin browsing to other sites without issue. How do I do this on a my 5508 WLC?
View 12 Replies
View Related
Oct 30, 2012
with our WLC 5500 controller, once the clients get the DHCP address the page is not redirecting them to the guest portal.What is the best way to check as to why the redirection is failing.
View 8 Replies
View Related
