Linksys Wireless Router :: WRT610N - HTTPS Secure Login To Admin Page?
Mar 29, 2013
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
View 6 Replies
ADVERTISEMENT
Jul 13, 2012
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies
View Related
Feb 3, 2013
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies
View Related
Feb 20, 2012
Is there a way to put a login banner on the ACS admin web page? Either display it directly on the web page or do a redirect to a banner page? Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
We are using ACS 5.3 running on VMWare.
View 2 Replies
View Related
Feb 16, 2012
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
View 6 Replies
View Related
Nov 18, 2011
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
View 5 Replies
View Related
Aug 17, 2012
I recently replaced my RV042 with an RV042G. I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042). When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly. Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate. I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.
View 2 Replies
View Related
Mar 11, 2012
I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);
Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.
View 1 Replies
View Related
Feb 23, 2012
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
View 1 Replies
View Related
Dec 18, 2011
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1:
Not shown: 65531 closed ports
PORT STATE SERVICE
139/tcp open netbios-ssn
443/tcp open https
445/tcp open microsoft-ds
1780/tcp open unknown
View 2 Replies
View Related
Mar 26, 2013
Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies
View Related
Oct 24, 2011
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
View 7 Replies
View Related
May 3, 2012
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
View 1 Replies
View Related
Apr 30, 2007
I seem to have lost my username and password for the admin page for my WRT54G router.Is there a way to retrieve or reset the login?
View 9 Replies
View Related
Apr 1, 2012
I want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies
View Related
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Feb 9, 2013
Is it possible to change the look of welcome page (guest login) to change so that it is personal. Of course it would be great if the guests have to log on your personal page.On this page you would be able to indicate the rules and and limitations. It would also be a good option for certain that your guests a limited time duration for the connection and gives max download. This would also be found to be in a log.
View 2 Replies
View Related
Mar 23, 2012
I tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.
View 1 Replies
View Related
Jun 11, 2011
When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)
View 9 Replies
View Related
Jan 25, 2011
Config:
Netgear ProSafe Gigabit Router is my DHCP Server -- The entire home net work is on the same subnet (192.168.15.xxx)
Linksys E4200 configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
Linksys WRT610N configured as an access point ONLY -- wired connection -- static IP assigned -- DHCP server turned off
3 -- 5 port gigabit switches
1 -- 8 port gigabit switch
No more than two switches between any two wired devices Both Linksys access points have the same SSID and WPA2 security phrase -- total of 4 radios Nonoverlapping channels are selected on both the 2.4Ghz and 5.0Ghz radio to minimize interference All computers are running Windows 7 Professional 64bit with all the latest updates Two iPhones and one iPad also access the network All LAN and WAN connectivity is working as designed?
Problem:
guest SSID is turned on
password is established
All devices will connect to the guest SSID and the E4200 is assigning an ip address to the device in the 192.168.33.xxx range which is what it's supposed to do.When I open a web browser, I am not automatically redirected to the Cisco Login Page. If I enter 192.168.33.1 as the URL, the login screen is presented. I enter the password I have created in the guest admin page on the wireless guest tab. I then see a blank page and a URL of 192.168.33.1/guestnetwork.asp. THIS IS WHERE I GET STUCK. THE ONLY WAY TO EVER SEE THE LOGIN PAGE AGAIN IS TO REBOOT THE E4200, otherwise you just get unable to connect messages when opening web browsers and the wireless status icon in the system tray shows a yellow exclamation mark.
I successfully connect to the guest SSID but I do not get access to the internet. When I type ipconfig, I see that the DNS is set to 192.168.33.1 which does not exist on my network. I assume there's some internal NAT magic that is supposed to happen in the E4200 to bridge me over to my 192.168.15.xxx network but it doesn't seem to be happening.At the beginning of the call I specifically asked them if the E4200 must be the DHCP server in order for the guest SSID feature to work and they said no. 1.5 hours later they had no answers so they told me that it wasn't working because the E4200 was not the DHCP server. The documentation says nothing about a DHCP requirement for guest AP service. Linksys support further could not answer what you would do if you needed more than one AP with guest service enabled.It seems like this is a firmware issue but it may be the guest SSID service requires the E4200 to also act as the DHCP server. Whether this is a bug or if the router/AP is working as designed?
View 9 Replies
View Related
Aug 11, 2011
I have an E3000 with firmware version 1.0.04 with WiFi configured as:Guest5GHz (only N)2.4 GHz (only G)I use the guest network access for my guests or my neighbor.Usually they connect and the first page they see in the browser is the http://192.168.33.1/login.asp were they put the password. Some times shomething don’t work and the browser don’t show the page, so the people can’t use the connection because they get a timeout error.The only solution I have in this case is to resart the router, but sometimes is not enough and I have to fisically shotdown and restart it.The login.asp page starts with: This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc. the contents of this file may not be disclosed to third parties, copied or duplicated in any form without the prior written permission of CyberTAN Inc. This software should be used as a reference only, and it not intended for production use! What about a firmware update to fix it and give the control from the web administration over the guest network?
View 5 Replies
View Related
Nov 13, 2007
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
View 9 Replies
View Related
Dec 14, 2010
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
View 9 Replies
View Related
Jul 12, 2011
When setting up my e1000 router for a secure domain it automatically opened a non secure one that my neighbors are using. How can I cancel it?
View 2 Replies
View Related
Jul 3, 2012
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies
View Related
Jan 29, 2012
I have a binatone wi-fi modem. Internet is working good from router but i am not able to connect to router admin page i.e 192.168.1.1 and not be able to change wi-fi password.
View 3 Replies
View Related
Apr 28, 2013
Region : UnitedKingdom
Model : TD-W8961ND
Hardware Version : Not Clear
Firmware Version : V.3
ISP : ADSL24
Using windows 7 and 8 on different machines I am unable access my routers web based set up.
I enter the usual "admin" and password in the login box. 3 goes and then get error message. or hangs on waiting.(connected to the router with Ethernet Cable). Could this be a windows based problem. I think it was ok on XP but that is gone now. Router is working fine but I just cant access it to alter any settings.
My 2 other spare routers which are not TP-link also have the same problem.
View 1 Replies
View Related
Aug 29, 2012
i want to stablish a new internet connection through bsnl broad band tell me hou i can install and run internet.
View 1 Replies
View Related
Feb 21, 2013
I can put login into the router just fine.. But the same login doesn't seem to work via web browser
View 2 Replies
View Related
Feb 10, 2012
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
View 19 Replies
View Related
May 22, 2012
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies
View Related
Jun 6, 2012
I go into my login page and all I see is blank. Just a white screeb. I have put in my IP address, I have no idea what I should do. I have been trying to fnd my password but the page has no login.
View 3 Replies
View Related
Feb 14, 2012
We set up our new Linksys last night but when the password was written down there is no distinction between upper and lower case letters - I can't login to an account page or do anything and I needed a password for a visiting friend.
View 1 Replies
View Related
