I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1: Not shown: 65531 closed ports PORT STATE SERVICE 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 1780/tcp open unknown
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
I just got a WET54GS5 to use for game systems. i wa able to use the software in order to get the system online and working, but i am not able to access the wireless bridge though the web page. the username is blank and i put in the correct password, but it does not go through.
I'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
"The connection was reset. The connection to the server was reset while the page was loading"
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
It's been a while since I sent into my router and messed with any of the Storage setting. I recently decided to change things around so I recently went in the router and attempted to access the Storage page but all I get is a blank page with this address http://192.168.1.1/storage/Disk_Management.asp.
I recently (~month ago) switched to a new computer after my old one (which I had configured the router on previously with no problems) died.Since then, I have been unable to access my router's config page (entering in the ip address simply results in a blank page with no prompt for username/password). Switching browsers (I've tried Firefox 5 and IE 8) does not solve the problem, nor does disabling AdBlockPlus/NoScript on Firefox. Any way to access my router so I can begin forwarding ports again?
I have the issue of being unable to access my router configuration page. My standard gateway IP (220.127.116.11), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
Before, I can access admin panel of router via 192.168.1.1 on any computer, be it wired or wireless.This time, I can't anymore.This time, I can only access admin panel on 1 computer only. The computer in which it's directly connected to the router, wired. All other computers, connected to a switch, which the switch is also connected to router, can no longer access admin panel.I can still open 192.168.1.1 with a username/password prompt but I can't log in. It's like it's always wrong password. Same with accessing from laptop (wireless).Before, I can access admin panel from any computer (wired), even from laptop (wireless). There are times that I have to restart router in order to fix my internet connection. Only this time, I have to access it from the computer that's directly connected to router (wired).How do I revert it back so that all computers will be able to connect to admin panel of router?I have just finished upgrading firmware from 1.0.05 to 1.0.06 but I still have the same problem.
Just setup my new EA6500 router and while in general it seems to be performing ok I am experiencing some problems with the admin. It seems that frequently either via cloud or local i get the cannot find router message or waiting graphic which results me in having to manually reboot the router so that i can access the admin page again, The router still works fine but no admin access until i physically reboot. This kind of defeats the whole purpose of using cloud if just by accessing the router or making changes it leaves admin access inoperable!
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
I'm trying to access the browser based utility (@ http://192.168.1.1) on my router and having no luck. I've tried from two different computers (each Win 7) and each browser. I've tried wired directly to the blue/LAN ports and through Wifi. I've confimred that the IP is correct (or is at least the default gateway for each machine). The Cisco Connect tool can't find the router either.the only thing that can find the router is the CiscoConnect Express app on my iPhone.Internet is working fineish (some problems with Wifi), I just want to play with some settings.
I have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
i have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in