Linksys Wireless Router :: Cannot Connect To Admin Page At All On E3200
Feb 23, 2012
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
View 1 Replies
ADVERTISEMENT
Dec 18, 2011
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1:
Not shown: 65531 closed ports
PORT STATE SERVICE
139/tcp open netbios-ssn
443/tcp open https
445/tcp open microsoft-ds
1780/tcp open unknown
View 2 Replies
View Related
Feb 3, 2013
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies
View Related
Oct 24, 2011
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
View 7 Replies
View Related
May 3, 2012
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
View 1 Replies
View Related
Apr 30, 2007
I seem to have lost my username and password for the admin page for my WRT54G router.Is there a way to retrieve or reset the login?
View 9 Replies
View Related
Mar 29, 2013
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
View 6 Replies
View Related
Apr 1, 2012
I want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies
View Related
Aug 5, 2012
Is there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies
View Related
Dec 25, 2012
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
View 3 Replies
View Related
Feb 28, 2011
For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
View 2 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
Nov 13, 2007
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
View 9 Replies
View Related
Feb 19, 2013
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
View 1 Replies
View Related
Dec 14, 2010
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
View 9 Replies
View Related
Oct 18, 2011
I just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?
View 1 Replies
View Related
Dec 18, 2011
The problem I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet.
View 1 Replies
View Related
Aug 31, 2012
I have an E3200 router. I had been experiencing connection problems with my desktop that was wired to the router, and in an attempt to resolve the issue reset the router to its factory defaults. Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to connect via ethernet are able to establish a connection. I have tested multiple cables with multiple computers using multiple ports on the router, to no avail. When I view the Status --> Ports page on the router, I can see the ports in use that I am connected to, but that is the only sign of connection that I get.
View 1 Replies
View Related
May 14, 2011
I have purchased a new E3200 to replace my old Linksys router. It locates my computers and sets up a network, but cannot connect to the internet via my Comcast cable modem. I have read on this forum about Mac address issues, but it has located the Mac address. The internet IP address is all zeros, and releasing and renewing the IP does nothing
View 9 Replies
View Related
Jun 17, 2012
I have a Telus Wireless modem and got a linksys router to try and expand the range & strength of the wifi. However,whenever I plug in the router and try to set it up, I can get connected to the router but no internet connection.I have tried everything I can - restarted the modem and the router several times, connected and reconnected, rebooted the whole of the router system, connected with an ethernet cable straight to the router from my laptop. In the settings, I have tried to mess around with the settings and more, and whenever I screw up I reset the router to defaults again.
View 3 Replies
View Related
Jan 3, 2012
I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet
View 3 Replies
View Related
Jun 10, 2011
Will all usb printers be able to connect to the e3200 by usb with the firmware update? If not, what printers will be supported?
View 9 Replies
View Related
Jul 3, 2012
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies
View Related
Jan 29, 2012
I have a binatone wi-fi modem. Internet is working good from router but i am not able to connect to router admin page i.e 192.168.1.1 and not be able to change wi-fi password.
View 3 Replies
View Related
Dec 2, 2012
Just installed the E3200. Can connect other computers but not IOS devices to the router, except through the "guest" port.
View 2 Replies
View Related
Apr 15, 2012
I'm using a Linksys E3200 router with a Motorola modem and an elite xbox 360 with a wireless N networking adapter. (Black with two antennas.) I just recently bought this router because I wanted some faster gaming. I wanted to put my xbox on the 5ghz so it would have it all to itself, and have the two laptops share the 2.4ghz. But it won't let me onto the 5ghz band... I can see it on my xbox but it won't connect to it at all. I can get onto the 2.4 band but its at 802.11G, so its not even giving me N there, when it should be. I'm not sure if this is an issue with my adapter or router...I tried finding stuff about it, and it looked like people were blaming it on linksys, but that was almost a year ago. And there was never an update on what happened.I can see the 5Ghz band on my xbox (but only if the channel width is on 20Mhz only), but I can't find it on my computer. Which I find weird. I've been trying a lot of things and I just can't get my laptop to find it. So nothing is using the 5 band, and all my devices are crowded onto the 2.4...Is there some step in setting up the 5Ghz band that I'm missing maybe?
View 4 Replies
View Related
Jul 21, 2012
I just bought the E3200 and have it all set up and have been able to successfully print from the USB port. I want to know if you can use a USB hub to connect multiple devices to the router. I found a couple of similar questions on the forum, but they're all back in 2011 before the 1.4 update to Cisco Connect.
View 1 Replies
View Related
Feb 9, 2012
I bought the E3200 to replace an older Linksys model. The older model worked but the signal was weak throughout the house. I installed the e3200 using the Cisco connect software but it told me that it wasn't sure I was connected to the internet. I wasn't. Showed a strong signal but could not connect via wireless devices or from the cable from the router to the desktop.
I have LUS Fiber service which does not use a modem. I have had them recycle the signal several times and have done tried many different variations of the MAC numbers from ipconfig or from cloning. Have also tried it with the MAC cloning disabled so the router's MAC number is used. I have reset, rebooted and done just about every possible option.
Spoke with my provider many times and they insist they are sending me a signal. They also recognized the router's MAC number on their end.I purchased one router and it wouldn't connect, so I exchanged it. All these shenanigans I have gone through are with the second router because I figured the hardware isn't the problem.
View 1 Replies
View Related
Jun 17, 2011
I had Cisco Connect and USB printing off of the E3200 working, but now I'm getting an error and cannot print to HP Laserjet P1006 on my E3200's USB port. Cisco Connect has an error: Error code: 80004005 Model name: Linksys E3200 Model number: E3200 Serial number: Firmware version: 1.0.01 build 3 Operating system: Windows 7 Software version: 1.4.11145.0 Connection type (WAN): DHCP IP address (LAN): 192.168.0.253 IP address (WAN): 192.168.2.100 Computer IP address: 192.168.0.149
View 9 Replies
View Related
Apr 25, 2012
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
View 1 Replies
View Related
Sep 23, 2012
I just installed an E3200 to replace my old Linksys. All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine. I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.
View 3 Replies
View Related
Sep 3, 2012
I'm amazed that the entire e3200 support page is down. Anyways until somebody from Cisco figures that out, I need analternate download link to the Cisco Connect software specifically for the E3200.
View 2 Replies
View Related
Oct 21, 2011
I upgraded 3 days ago from a (WRT160N ver. 1) to a (E3200) After setting it up and syncing all the devices including the XBOX 360. After signing into Live I noticed that every time I power off and power on the console it's IP address would change causing the NAT to become moderate so I went over to the Xbox360 open the Network settings and Manually set the IP address Mac address, Gateway address. Then I opened the routers settings page and Port Forwarded the correct ranges also copied the IP address I manually entered earlier on the Xbox 360. On the router side I saved the changes restarted the console and my NAT was open, but here's the Issue now when I go to sign into Live I get a pop up saying I can't connect to Live to "Test the Connection". After I "Test the Connection" then and only then I can sign into Live.
View 9 Replies
View Related
