Linksys Wireless Router :: E3200 / Possible To Use As USB Hub And Connect Multiple Devices?

Jul 21, 2012

I just bought the E3200 and have it all set up and have been able to successfully print from the USB port. I want to know if you can use a USB hub to connect multiple devices to the router. I found a couple of similar questions on the forum, but they're all back in 2011 before the 1.4 update to Cisco Connect. 

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: E3200 Can Connect Other Computers But Not IOS Devices

Dec 2, 2012

Just installed the E3200. Can connect other computers but not IOS devices to the router, except through the "guest" port.

View 2 Replies View Related

Linksys Wireless Router :: E3200 Couldn't Connect Via Wi-Fi Devices

Feb 9, 2012

I bought the E3200 to replace an older Linksys model. The older model worked but the signal was weak throughout the house. I installed the e3200 using the Cisco connect software but it told me that it wasn't sure I was connected to the internet. I wasn't. Showed a strong signal but could not connect via wireless devices or from the cable from  the router to the desktop.
 
I have LUS Fiber service which does not use a modem. I have had them recycle the signal several times and have done tried many different variations of the MAC numbers from ipconfig or from cloning. Have also tried it with the MAC cloning disabled so the router's MAC number is used. I have reset, rebooted and done just about every possible option.
 
 Spoke with my provider many times and they insist they are sending me a signal. They also recognized the router's MAC number on their end.I purchased one router and it wouldn't connect, so I exchanged it. All these shenanigans I have gone through are with the second router because I figured the hardware isn't the problem.

View 1 Replies View Related

Linksys Wireless Router :: E3200 - Parental Control On Devices

Sep 12, 2012

I would like to see the full range of 24 hours for setting parental controls on devices.  As it stands now, I can only select a block of time that starts in the PM and ends in the AM.  This isn't very useful if for instance I want to limit internet while my kids are home alone after school, from 3 PM to 5 PM, or say on the weekends to limit it from 7 AM to 5 PM.  Just a suggestion that would make life a bit easier!

View 1 Replies View Related

Linksys Wireless Router :: E3200 - Set Up Parental Controls For Other Devices Via Web Interface?

Apr 8, 2012

Have set up parental controls for other devices via web interface. It does not take for one laptop. I see the device can add it to list but all settings dont work? Have reset router, removed and re-added device called support but found no solutions.

View 1 Replies View Related

Linksys Wireless Router :: E3200 Some Random Disconnects On Devices Using 2.4GHz Frequency

Jul 24, 2011

I just recently (4 days ago) purchased an E3200 router.  I noticed some random disconnects on my devices using the 2.4GHz frequency.I installed inSSIDer from MetaGeek to see what was going on and noticed some strange behavior where the Amplitude on the 2.4GHz randomly drops dramatically.  Sometimes its once every 10 minutes, other times it happens 5 times in one minute.  I can't figure out what is the cause.  The 5GHz signal is steady as a rock.

 What I tried so far:  Set the Channel to the least crowded channel instead of auto, upgraded the firmware, restarted the router all to no avail.  This is annoying to say the least.  It doesn't affect anything unless you are playing video games or running a remote desktop session, where a single disconnect is disastrous. I just upgraded from an old linksys wrt54g, tried a netgear n600 which was terrible, then swapped it out for the Cisco E3200..

View 7 Replies View Related

Linksys Wireless Router :: Are E3200 Multiple SSIDs Diff LANs

Nov 28, 2011

I just got the E3200 and it's a pretty good router. Configured it to have 1 SSID as the 5Ghz SSID and the other as the 2.4 Ghz SSID. Since there are 2 SSIDs broadcasted, I was expecting machines connected to each distinct SSID to not be able to see each other, ie expecting the 5Ghz SSID to be a private LAN1 and the 2.4 Ghz SSID to be LAN2? It turns out machines on either SSID can see each other, so it looks like it on 1 big LAN even though there are 2 SSIDs.Doesn't a SSID map to a unique LAN even though they are in the same router?

View 2 Replies View Related

Linksys Wireless Router :: EA6500 Multiple Devices Under One Device?

Oct 14, 2012

I got the new EA6500.  For the last few days I've noticed there are multiple devices showing under one device with different IP addresses.  In the beginning they show up individually with their own device names, then somehow combine.  Each device is different ie. computer, phone, DirecTV box, etc.  I did a hard reset, re-flash and still it keeps happening. 

View 9 Replies View Related

Linksys Wireless Router :: WRT54GS Multiple Devices Not Able To Detect

Jan 18, 2012

I have a Linksys Wireless-G WRT54GS with SpeedBooster.When I turn on 3 devices on Wi-Fi ( for instance 2 Apple MAC Computers, 1 Windows PC, and a wi-fi printer ), in other words 3 to 4 devices, everything works fine.  BUT when I add another device later in the day ( lets say an iPad ), the iPad is not able to access the wi-fi connection.  I get a message saying that another device is already using the connection.If I reset the router, then the iPad will be able to get in along with 2 or 3 other devices.  If I try an extra device, I get the same problem.What can be causing this?  I was under the impression that the router can handle an unlimited amount of wi-fi devices.

View 4 Replies View Related

Linksys Wireless Router :: WRT54G2 Won't Allow Internet Access For Multiple Devices

Dec 25, 2011

My PC will connect just fine, but it is the only device on my network that the router will allow internet access. The router will allow other devices (DVR, laptop, nook) to connect to it, but won't allow those devices to connect to the internet. Each device will show the same error, - "connected to linksys - no internet". I've reset the router many times with no results.

View 1 Replies View Related

Linksys Wireless Router :: EA6500 Multiple Devices Under One Device Workaround?

Dec 9, 2012

Once your devices start showing up in your device list make a DHCP reservation for each device. (after confirming that no other devices are listed under it).
 
If you have a device that has multiple MAC & ip addresses under it you MUST first determine what the devices are listed & power-down before you can delete the device. Also note that some wired devices will still show as connected so you must have to either power down the device by pulling Th power cord OR disconnect the ethernet cable.

View 2 Replies View Related

Connect Multiple Devices To My Router?

Oct 2, 2012

I want to connect my ps3, sky hd+ box and samsung smart tv. Upstairs is my wireless router and I have connected to this by using a power supply networking adaptor (duvelo). I have since purchased a cheap ethernet switch from ebay and plugged this into the power adaptor connection next to my ps3, sky hd+ and samsung smart tv downstairs. I thought by connecting these 3 devices to the switch (which is connected to the duvelo adaptor) I could have all 3 devices simultaneously connected online. However, I still can only have 1 ethernet cable in the switch at once and hence only connect 1 device at a time.

View 2 Replies View Related

Linksys Wireless Router :: E3200 - Connect USB Hub?

Oct 18, 2011

I just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?

View 1 Replies View Related

Linksys Wireless Router :: E3200 Cannot Connect To Internet?

Dec 18, 2011

The problem I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet.

View 1 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect Wired?

Aug 31, 2012

I have an E3200 router. I had been experiencing connection problems with my desktop that was wired to the router, and in an attempt to resolve the issue reset the router to its factory defaults. Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to connect via ethernet are able to establish a connection. I have tested multiple cables with multiple computers using multiple ports on the router, to no avail. When I view the Status --> Ports page on the router, I can see the ports in use that I am connected to, but that is the only sign of connection that I get.

View 1 Replies View Related

Linksys Wireless Router :: E3200 - Cannot Connect To Internet

May 14, 2011

I have purchased a new E3200 to replace my old Linksys router.  It locates my computers and sets up a network, but cannot connect to the internet via my Comcast cable modem.  I have read on this forum about Mac address issues, but it has located the Mac address.  The internet IP address is all zeros, and releasing and renewing the IP does nothing

View 9 Replies View Related

Linksys Wireless Router :: E3200 Will Not Connect To The Internet

Jun 17, 2012

I have a Telus Wireless modem and got a linksys router to try and expand the range & strength of the wifi. However,whenever I plug in the router and try to set it up, I can get connected to the router but no internet connection.I have tried everything I can - restarted the modem and the router several times, connected and reconnected, rebooted the whole of the router system, connected with an ethernet cable straight to the router from my laptop. In the settings, I have tried to mess around with the settings and more, and whenever I screw up I reset the router to defaults again. 

View 3 Replies View Related

Linksys Wireless Router :: E3200 Cannot Connect To Internet

Jan 3, 2012

I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet

View 3 Replies View Related

Linksys Wireless Router :: Will All Usb Printers Be Able To Connect To E3200

Jun 10, 2011

Will all usb printers be able to connect to the e3200 by usb with the firmware update? If not, what printers will be supported?

View 9 Replies View Related

Linksys Wireless Router :: Cannot Connect To Admin Page At All On E3200

Feb 23, 2012

I don't have to completely reset my router as I have a ton of configs on it.  Anyway, recently for some reason, I lost all access to my admin page.  Cisco Connect also cannot find the router.  Funny thing is that all of my wireless profiles work just fine.  Meaning all of the computers in my home connect to the internet just fine using the router.  Both the guest access and WPA connected machines.[url]...

View 1 Replies View Related

Linksys Wireless Router :: E3200 / Can't Connect To 5Ghz Band

Apr 15, 2012

I'm using a Linksys E3200 router with a Motorola modem and an elite xbox 360 with a wireless N networking adapter. (Black with two antennas.) I just recently bought this router because I wanted some faster gaming. I wanted to put my xbox on the 5ghz so it would have it all to itself, and have the two laptops share the 2.4ghz. But it won't let me onto the 5ghz band... I can see it on my xbox but it won't connect to it at all. I can get onto the 2.4 band but its at 802.11G, so its not even giving me N there, when it should be. I'm not sure if this is an issue with my adapter or router...I tried finding stuff about it, and it looked like people were blaming it on linksys, but that was almost a year ago. And there was never an update on what happened.I can see the 5Ghz band on my xbox (but only if the channel width is on 20Mhz only), but I can't find it on my computer. Which I find weird. I've been trying a lot of things and I just can't get my laptop to find it. So nothing is using the 5 band, and all my devices are crowded onto the 2.4...Is there some step in setting up the 5Ghz band that I'm missing maybe?

View 4 Replies View Related

Linksys Wireless Router :: Connect Error 80004005 With E3200

Jun 17, 2011

I had Cisco Connect and USB printing off of the E3200 working, but now I'm getting an error and cannot print to HP Laserjet P1006 on my E3200's USB port. Cisco Connect has an error: Error code: 80004005 Model name: Linksys E3200 Model number: E3200 Serial number: Firmware version: 1.0.01 build 3 Operating system: Windows 7 Software version: 1.4.11145.0 Connection type (WAN): DHCP IP address (LAN): 192.168.0.253 IP address (WAN): 192.168.2.100 Computer IP address: 192.168.0.149

View 9 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect To Wifi Radios Wirelessly?

Sep 23, 2012

I just installed an E3200 to replace my old Linksys.  All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine.  I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.

View 3 Replies View Related

Linksys Wireless Router :: E3200 Cisco Connect Software Download?

Sep 3, 2012

I'm amazed that the entire e3200 support page is down.  Anyways until somebody from Cisco figures that out, I need analternate download link to the Cisco Connect software specifically for the E3200.

View 2 Replies View Related

Linksys Wireless Router :: E3200 Can't Connect To Live To Test Connection

Oct 21, 2011

I upgraded 3 days ago from a (WRT160N ver. 1) to a (E3200) After setting it up and syncing all the devices including the XBOX 360. After signing into Live I noticed that every time I power off and power on the console it's IP address would change causing the NAT to become moderate so I went over to the Xbox360 open the Network settings and Manually set the IP address Mac address, Gateway address. Then I opened the routers settings page and Port Forwarded the correct ranges also copied the IP address I manually entered earlier on the Xbox 360. On the router side I saved the changes restarted the console and my NAT was open, but here's the Issue now when I go to sign into Live I get a pop up saying I can't connect to Live to "Test the Connection". After I "Test the Connection" then and only then I can sign into Live.

View 9 Replies View Related

Linksys Wireless Router :: E3200 And Motorola DSL 2210-02 Will Not Connect To Internet?

Oct 29, 2011

I justed purchased a Linksys E3200 router to replace my old router that gave up the ghost.  I have it paired with a Motorola 2210-02 DSL modem.  The software that came with the router has created two networks but is unable to connect to the internet.  I have tried on both my PC and MacBook Pro and niether work.  I have the modem connected directly to my Mac and can get to the internet, so I know the modem is working correctly.  

View 6 Replies View Related

Linksys Wireless Router :: E3200 Lost Internet Connect Every A Couple Hours

Dec 4, 2012

I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
 
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.  

View 9 Replies View Related

Linksys Wireless Router :: E3200 Router Can't Connect To Internet

Mar 20, 2013

I bought a Cisco-Linksys E3200 8 months ago and it worked well until last month. I usually power down the router after midnight & power up in the morning and evevry time it can connect to internet through DSL modem without problem until this Feb. Most of the time after powering up the router it just can't connect to internet anymore. I am sure the AT&T DSL modem is working. I have to reboot/reset the router & DSL modem several time to get router to connect to internet again. The order of resetting/rebooting DSL modem & E3200 router seems to make no difference. It just appears suddenly the router can connect to internet by chance. I changed router IP and it didn't work either. It's really annoying becuase I have to spend 10~40 minutes to resetting/rebooting DSL modem & router to get internet connection every day. 

View 9 Replies View Related

Linksys Wireless Adapters :: WET610N Bridge With Multiple Devices?

Dec 11, 2009

I am interested in purchaseing a WET610N wireless Bridge for my new XBOX 360 to connect to my existing wireless, and wire network.  I was wonder if the device can be connected to a 5 port network switch and used on multiple devices such as my TV. 

View 5 Replies View Related

Multiple USB Devices To Wireless Router

Aug 15, 2012

Can I use a USB hub to connect multiple usb devices to a single usb port on a wireless router? I want to connect a usb printer, usb scanner, and usb external hard drive.

View 1 Replies View Related

D-Link DIR-655 :: Can't Connect Multiple Devices

Apr 5, 2012

We can only connect 2 devices at a time. Someone suggested that it may be a setting with my wireless router.

View 2 Replies View Related

Linksys Wireless Router :: E2500 Can't Connect All Devices

May 3, 2012

can't connect all my devices like an Iphone, Nook or another computed to the wireless network with the e2500, we have three devices but the others can't connect.

View 3 Replies View Related

Linksys Wireless Router :: EA3500 Why Some Devices Won't Connect

Mar 30, 2013

Just installed a Linksys N750 (EA3500) router (WAN - LAN setup). I settled both band networks : 2.4 Ghz and 5Ghz with different SSID and different WAP2/WAP personal mixt.  WHile some devices will show both networks correctly, I'm facing issues with the 5Ghz band and wonder if this is sigh of some kind of failure:
 
- while my iPad offered both signals and let me set the 5 Ghz band, it is showing weak signal and stall on loading webpages; as soon as I instead put it on the 2.4Ghz band, (standing at same location of course), everything runs smoothly, excellent signal. 
 
- I have a Mac Mini and PS3 side by side same location.  The Mac Mini seems to works flawlessly under both bands, 2.4 or 5  - excellent signal. However, the PS3 fails its connexion test and states that signal is not perceptible on the 5Ghz. But connect as a snap on the 2.4 Ghz band.
 
- Got on and off 5Ghz signal on a laptop; connected to 2.4Ghz, everything runs perfect.
 
- iPhones 4S : I don't even see the 5Ghz SSID, but I get both the 2.4 and Guess account..So I'm tempted to conclude that some devices just can't follow the pace (??) to connect on 5Ghz..

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved