Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1: Not shown: 65531 closed ports PORT STATE SERVICE 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 1780/tcp open unknown
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
Is there a way to put a login banner on the ACS admin web page? Either display it directly on the web page or do a redirect to a banner page? Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
I'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
"The connection was reset. The connection to the server was reset while the page was loading"
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.
I'm trying to setup a new Cisco ASA 5505. I performed the "config factory-default" command and subsequently pulled an IP from my ASA. However, I am unable to pull up the ASDM GUI launch page using IE9, Google Chrome, or Firefox using my Windows 7 computer. Using Wireshark, I can see that I'm getting a TLSv1 handshake failure.I fired up a Windows XP VM inside of Virtual Box to see if it would work better. Turns out my XP VM with IE 8 pulls up the ASDM launch page without a problem. why my Windows 7 system can't pull up the ASDM launch page?
I have an AP(Cisco Lynksis Wireless G WAP54G) with one port (LAN) on the back, i have tried several time accessing the administration page but in vain. I reseted the AP (holding the reset button within 10 secondes) and try again to access through my internet brower but still having the same issue on accessing the admin page. The main target is to access the admin page and configure settings in order to amplify my signal in some offices away.
I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
Region : Netherlands Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
We have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
I recently replaced my RV042 with an RV042G. I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042). When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly. Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate. I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.
I have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.