Cisco WAN :: Can't Access Point Admin Page (WAP4410n)

Feb 26, 2012

I'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
 
"The connection was reset. The connection to the server was reset while the page was loading"
 
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.

View 5 Replies


ADVERTISEMENT

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Can't Access Admin Page Through Router?

Jul 3, 2012

Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.

View 1 Replies View Related

Unable To Access Admin Page Of Baitone Router?

May 22, 2012

I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1

View 3 Replies View Related

Cisco Routers :: How To Access RV220W Admin Page On IPad

Jul 14, 2011

How to access the admin page of the RV220W from an iPad wih the default security certificate? If so, what steps did you go through? Or is this only possible when purchasing a certificate?

View 10 Replies View Related

Cisco Wireless :: Can't Access WAP4410N Management Page

Nov 8, 2010

I just managed to get hold of an old second hand WAP4410N from a friend who got it for work but never really had the time to get it working. I powered it up and performed a 30/30/30 reset to get rid of anything he may have done to it but now I'm struggling to get to the management page. The power light is steady and the ethernet light shows activity but I can't seem to find it on any IPs. I've tried both hooking it into a router and setting up a laptop with an IP of 192.168.1.2,  subnet mask of 255.255.255.0 and gateway of 192.168.1.245 and I still have no luck. I'll fiddle with it more tomorrow but it'll probably just involve messing around with more settings and resetting it again, nothing of any real structure. Is there any way of forcing a new firmware onto it over the MAC address or something, for example?

View 3 Replies View Related

Protocols / Routing :: Can't Access Wireless Repeater Set-up / Admin Page

Dec 27, 2012

I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"

View 3 Replies View Related

Linksys Wireless Router :: Unable To Access Cisco Admin Page For 54G V5

May 3, 2012

I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5.  Also need to connect VPN but unable to. 

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 Lost Access To The Admin Page

Nov 13, 2007

I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.

View 9 Replies View Related

D-Link DIR-655 :: SBS2008 - Network Filter Blocks LAN Port Access To Admin Page

Oct 16, 2011

I'm using my 655 as a WAP, so nothing is connected to the WAN port.  Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page.  Even if I put the connecting PC's LAN MAC in the tablet.

View 9 Replies View Related

Linksys Access Point :: WAP4410N Can't Set It Up

Jul 1, 2012

I need to set up some security cameras here, and the boss has a never used Cisco WAP4410N router. I gotta use my own personal laptop, it's a small netbook, Aspire One DN55E using Windows 7 and Firefox. The network switch is by ZHONE.The wireless accesspoint has green lights on power and wireless, but not on Ethernet or PoE. The switch has power as green, the status blinks green, and co mode is red, everything else is not on. The router is plugged into the first lan plug, I can't plug it in ethernet, as my plugs don't fit. My laptop is connected to the stitch in the secon hole, and the third hole on te switch is connected to the internet. My laptop is receiving wired internet, and it's working well. It's via comcast cable.Now, where it say's 'Configuring the wap4410N Access Point in the book that came with the router, under 'Launching the Web-Based COnfiguration Utility' I seem to from above already accomplished step 1, which is 'Connect your computer to the same network the WAP4410N Access Point is connected to.
 
Yet, in the next step, it says to configure to the same subnet access point.Now..... I've followed all sorts of things requiring me to do stuff with TCP-i4 and 6 in odd little places in my computer, I've typed in on my wireless network password the default access point in the book as well as the default mask, nothing. I went to firefox, and typed it in my browser, nothing- says each time it's taking too long.I can't configure it, the next step says launch firefox, and I can't pull this off, as firefox never finds that default address.This is too hard for something so simple. It shoud be plug in, software pops up on my computer, a quick wizard, and I'm done. It's been a few days, and I am sweating and hot and am thinking about reenacting scenes from terminator 2 at the cisco headquarters.

View 1 Replies View Related

Cisco Wireless :: WAP4410N Access Point

Sep 29, 2011

I recently purchased a WAP4410N and I have some problems getting it to work. I am on a 192.168.1 network so everything should be ready to go. I am unable to ping the default address 192.168.1.245 for the wireless. During the process of resetting the device I am able to ping it for a few seconds. I am able to see the wireless connection but I am unable to access it even though it is unsecured. All lights are on the device except the PoE light.

View 4 Replies View Related

Linksys Access Point :: Cannot Access Configuration Page For WAP11 Access

Jun 12, 2007

Cannot access configuration page for WAP11 Access

View 9 Replies View Related

Cisco Wireless :: WAP4410N - Monitoring Of Access Point

Mar 17, 2013

i have more then 25 Cisco WAP4410N AP put is our office. i put 4 AP in each floor.we are using signal SSID for all AP. I have two question

 1: want to monitor all AP if any is down we can trouble shoot it .

2: with some user have problem before connecting it show full signal but after connecting signal is drop.some time
connected PC is automatically restart wireless connectivity.
 
As a Admin i want to monitor what is going on.

View 2 Replies View Related

Linksys Access Point :: WRT160N And WAP4410N Repeater

Sep 15, 2010

I want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?

View 5 Replies View Related

Linksys Access Point :: Setting Up AP2 WAP4410N To Be A Repeater For AP1?

Oct 12, 2011

I have AP1 setup with WPA2-Enterprise.  How would I setup AP2 (WAP4410N) to be a repeater for AP1?

View 1 Replies View Related

Linksys Access Point :: WAP4410N Won't Assign IP Addresses?

Dec 18, 2012

I have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch. All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all. Sometimes I can get 1 PC to connect but what's strange is I can view my networked folders and such but cannot access the internet. I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.

View 1 Replies View Related

Cisco Wireless :: WAP4410N Access Point Disconnect After Short While?

Jun 12, 2011

I got a CISCO wap4410n access point and it is disconnecting uses after a shorl while. I hv to again connect them manually.

View 1 Replies View Related

Linksys Access Point :: Settings WAP4410N As Repeater For WRT120N

Jul 19, 2011

I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
 
- how i configure my WAP4410N as a repeater?

- is there any settings that i must set on the WRT120N, before combining the WAP4410N?

View 1 Replies View Related

Cisco Wireless :: Wap4410n - Access Point Rejects The Username And Password

Jun 25, 2010

Recently I have purchased two brand new wap4410n access points.
 
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
 
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
 
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
 
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
 
I still get the same error as above.
 
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
 
Cisco, when contacted, said both access points must be faulty and I should replace them.
 
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.

View 4 Replies View Related

Unable To Access Router Admin Page Haier R800 Router

Dec 13, 2012

Unable to access router admin page for Haier model R800

View 1 Replies View Related

Linksys Wireless Router :: E1200 - How To Access Router Admin Page

Apr 1, 2012

I want access the my E1200 website in order to implement new username and password to secure the network.

View 1 Replies View Related

Linksys Access Point :: WAP4410N - Internet Connection Always Connect And Disconnect

Aug 18, 2011

I have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.

View 1 Replies View Related

Cisco Wireless :: WAP4410N Increase Range Of Access Point By Replacing Antenna

Jun 17, 2011

I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.

View 0 Replies View Related

Linksys Access Point :: Cannot Connect To WEP610N Set Up Page

Dec 14, 2012

Even using the static address I cannot connect to the unit's set up page.

View 1 Replies View Related

Linksys Access Point :: WRT 54GL - Configuration Page

Aug 30, 2007

My question is regarding gaining access to my Linksys wireless router configuration page. I recently turned my Linksys WRT54GL wireless router into an access point and since I have done so I am no longer able to access the configuration page for my router.

The problem that I am encountering is not one of connectivity, but rather entry. Prior to turning my wireless router into an access point I was able to connect to the router by means of my browser (192.168.1.1). I am still able to connect to the router, but whenever I type in a user name and password the router just simply does not recognize the information. I have tried resetting the router multiple times, but I am still denied access to my router despite having the correct user name and password. I have version 1.1 of the Linksys WRT54GL wireless router and have the latest firmware.

View 9 Replies View Related

Linksys Access Point :: Can't Find WAG160N Firmware Upgrade Download Page

Dec 23, 2009

Can't find WAG160N firmware upgrade download page on this site  A few mounth ago it existed

View 3 Replies View Related

Cisco Wireless :: WAP4410N - Unable To Log In To Web Admin From Apple MAC

Jan 8, 2012

I recently installed a WAP4410N for a customer without any problem, but a few days later I received a call requesting assistance as the customer could not login to the web admin page.
 
The login screen was showing, but it wasn't acceptingthe username and password that I had set. Today I visited customer to investigate.
 
I discovered that I could login without any problem using my Windows laptop, but that customer could not use any of their Apple MACs to login.
 
Apart from one Windows PC, all customer computers were Apple OS. Customer could login using their Windows PC without any problem.

View 2 Replies View Related

D-Link DIR-655 :: Can't Get To Web GUI Admin Page

Oct 30, 2011

I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout.  Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem.  Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.

View 5 Replies View Related

Linksys Wireless Router :: Does Cisco WAP4410N Wireless-N Access Point Support PPPoE

Feb 21, 2013

Does Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?

View 1 Replies View Related

Accessing The Router's Admin Page?

Jan 29, 2012

I have a binatone wi-fi modem. Internet is working good from router but i am not able to connect to router admin page i.e 192.168.1.1 and not be able to change wi-fi password.

View 3 Replies View Related

D-Link DIR-655 :: Can't Connect To Admin Page

Feb 19, 2013

I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Banner For ACS 5.3 Admin Login Page

Feb 20, 2012

Is there a way to put a login banner on the ACS admin web page?  Either display it directly on the web page or do a redirect to a banner page?  Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
 
We are using ACS 5.3 running on VMWare.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved