I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1: Not shown: 65531 closed ports PORT STATE SERVICE 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 1780/tcp open unknown
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
Before, I can access admin panel of router via 192.168.1.1 on any computer, be it wired or wireless.This time, I can't anymore.This time, I can only access admin panel on 1 computer only. The computer in which it's directly connected to the router, wired. All other computers, connected to a switch, which the switch is also connected to router, can no longer access admin panel.I can still open 192.168.1.1 with a username/password prompt but I can't log in. It's like it's always wrong password. Same with accessing from laptop (wireless).Before, I can access admin panel from any computer (wired), even from laptop (wireless). There are times that I have to restart router in order to fix my internet connection. Only this time, I have to access it from the computer that's directly connected to router (wired).How do I revert it back so that all computers will be able to connect to admin panel of router?I have just finished upgrading firmware from 1.0.05 to 1.0.06 but I still have the same problem.
Just setup my new EA6500 router and while in general it seems to be performing ok I am experiencing some problems with the admin. It seems that frequently either via cloud or local i get the cannot find router message or waiting graphic which results me in having to manually reboot the router so that i can access the admin page again, The router still works fine but no admin access until i physically reboot. This kind of defeats the whole purpose of using cloud if just by accessing the router or making changes it leaves admin access inoperable!
I have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
I'm trying to access the browser based utility (@ http://192.168.1.1) on my router and having no luck. I've tried from two different computers (each Win 7) and each browser. I've tried wired directly to the blue/LAN ports and through Wifi. I've confimred that the IP is correct (or is at least the default gateway for each machine). The Cisco Connect tool can't find the router either.the only thing that can find the router is the CiscoConnect Express app on my iPhone.Internet is working fineish (some problems with Wifi), I just want to play with some settings.
I have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
Okay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
I have a Linksys E1200 router.My problem is I have installed a camera system that allows remote viewing.I cannot access the system through the E1200 I am not very knowledgeable in net working.What do I need to do to access the DVR from a remote computer?
Trying all week to get my E1200 setup as an Access Point with my AT&T U-Verse 2WIRE Modem. [code] It just never seems to work correctly. It will connect for a second or 2 and then jam up. My ultimate scenario would be to have the E1200 just act as a wireless access point and have the 2WIRE do the rest: firewall, DCHP, etc.
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
i have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in