Trying all week to get my E1200 setup as an Access Point with my AT&T U-Verse 2WIRE Modem. [code] It just never seems to work correctly. It will connect for a second or 2 and then jam up. My ultimate scenario would be to have the E1200 just act as a wireless access point and have the 2WIRE do the rest: firewall, DCHP, etc.
View 9 RepliesIs it possible to use an E1200 as an access point? I am connecting it to an SE2500..
View 1 Replies View RelatedI have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies View RelatedI can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty. i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.
View 6 Replies View RelatedHow do you set up the E3000 for ATT u-verse?
View 2 Replies View RelatedI'm trying to use a WRT54GL with U-Verse. The problem is that the router does not get a connection to the modem. It can't ping the modem, and it doesn't show up on on the list of devices connected to the modem. DHCP assigns an IP address of 127.0.0.1, which is outside the range of the modem [192.168.1.1 ... 192.168.1.253]. The router is also showing a default gateway of 0.0.0.0, and a subnet mask of 255.0.0.0. (And yes, I have released and renewed the lease, rebooted the modem, and reconnected the modem.) The router WAN side is set to DHCP, and the operating mode was changed from gateway to router (the gateway setting doesn't work either, for that matter).
View 9 Replies View RelatedWhat happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedI have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
View 3 Replies View RelatedOkay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies View RelatedI'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
View 6 Replies View RelatedI had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies View RelatedI have a Linksys E1200 router.My problem is I have installed a camera system that allows remote viewing.I cannot access the system through the E1200 I am not very knowledgeable in net working.What do I need to do to access the DVR from a remote computer?
View 1 Replies View RelatedI have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies View RelatedI just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
View 5 Replies View RelatedI have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedI want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies View RelatedI have a new E1200 router. I VPN from home to my work computer just fine. since I can remotely access the router from work...what setup section of the router would I need to utilize to go backwards and access my home PC thru remote desktop? NAT? if so what are the instructions to do so.
View 1 Replies View RelatedWhy does my E1200 forget my Parental Control Password? This happens almost weekly and I have to use the "forgot password" option. It asks my security question, I answer it and set the new password to the same password it keeps forgetting. Why does this happen? Also, is there anyway to have total 24hr control on the Block Internet Access?
View 4 Replies View RelatedI want to set up an E1200 as a wireless access point for guests, and ordinarily I'd be happy to connect it LAN-to-WAN and have it create its own subnet, but I need to connect one office PC to it also because connecting the E1200 to the main gateway displaces that office PC from the last Ethernet port on the main router.
So I disabled DHCP on the E1200 and connected it LAN-to-LAN. The modem is at a fixed, non-configurable address of 192.168.0.1/255.255.0.0 and the main router is at 10.0.0.1/255.255.255.0. I set the E1200 to a static IP of 10.0.0.12/255.255.255.0.The E1200's primary wireless connection works fine. The guest access connects, but it does not prompt for a password and web pages generate a "failed to load" sort of message.I temporarily connected the E1200 as the main router and re-enabled DHCP, though I kept the static IP of 10.0.0.12/255.255.255.0, and in this configuration the guest access worked. I observed that it connected via 192.168.33.1/guestaccess.cgi (or something very similar to that).
I am swapping my AT&T DSL and Comcast cable for U-verse. In the basement, I have a Netopia DSL modem connected to a Linksys BEFRS81 v. 3 ethernet Cable/DSL router/8-port switch. Cat 5 cables are attached to the router, then run throughout the house so we are "networked" to the DSL modem and use a patch cord from laptop or desktop into the wall to get to the Internet.
View 1 Replies View RelatedHow do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View RelatedHow to install linksys wireless router to access point?
View 1 Replies View RelatedCan I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?
View 1 Replies View RelatedI have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
View 9 Replies View RelatedI'm currently using my WRT320N router as an access point (connected to another linksys router), but I've lost my username and password to access the web-based utility. So I need to press the reset button and set it up again. Currently everything is working fine, but I've forgotten how to configure the router for this purpose, and I can't find instructions in the user's guide online. I seem to remember it being troublesome. I know I have to assign a different IP address (currently I'm using 192.168.1.113.) What other settings (if any) need to be changed?
View 2 Replies View Related"Can I get my E2100L to receive a wireless signal from a different model Wireless Router and repeat it via wireless and Ethernet. Yes or NO?"
- If so, how, if u need to user guide here: E2100L User Guide
I am using a newer wireless router but would like to use my older wrt54g router as an access point (wired and wireless) at the other end of my house. how to do it, and what the specific settings should be, especially the security settings. I can connect the wrt54g via a homeplug (cannot run a LAN cable). I had previously tried an Aztech wireless homeplug but found the security feature to be worthless and everyone was able to "break-in".
View 3 Replies View RelatedCan the EA6500 be set up as an access point connected to a remote router which has a connection to the DSL modem?I want to replace one of my wireless access points with a faster wireless interface, but this will be connected via hard wire CAT-5 cable located away from my modem/router.
View 3 Replies View RelatedI have a Cisco RV082 and I would like to connect my E3000 to it and use it as just a wireless access point. Is it possible to do this with the E3000 so the RV082 is providing the routing functionality?
View 1 Replies View RelatedI have a Router WRT160N and need to connect an Access Point using a wireless bridge (i.e. cannot use cable between router and AP). Which Linksys Access Point model is recommended to use with this router?(No I dont want to use another WRT160N with DD-WRT!)
View 1 Replies View RelatedI have a WRT 160n I want to use as an access point. The cable company has provided the main router so I want to use the 160 as the access point. I have a switch attached to the router and have the 160 attached to the switch. I can ping and access the 160, however there signal strength has not changed and is still extremely low. I know that the strength on the router is very good when I plug it in to the cable modem.
View 1 Replies View Relatedi am thinking of buying Linksys x2000 , WAG160N or any other you suggest to use as a wireless access point. Is it possible?My setup is : I get my internet from my neighbor by ethernet cable from his router. My house is two-storied and ethernet cable comes to top left corner of first floor and the devices(two notebook) are on the bottom right corner at the second floor , insulation greatly reduces the signal strength.
View 5 Replies View Related