Linksys Wireless Router :: E1200 Do Not Have Internet Access As Default Gateway
Nov 11, 2011
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies
ADVERTISEMENT
Jul 28, 2011
I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies
View Related
Sep 5, 2012
I have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
View 3 Replies
View Related
Sep 10, 2011
Okay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it. When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need port forwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2.
View 3 Replies
View Related
Jun 18, 2011
I have a pocket wifi which allows you to connect up to five devices. my mum, sister and my phone can access it no problems but my laptop wont work.what will happen is:
- it connects automatically to the wifi
- but it has a little error mark on it
- and it says theres no internet access.
ive tried everything, ive ran several windows network diagnostics and it says the problem is the default gateway being unavailable.
View 4 Replies
View Related
Sep 12, 2012
I just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
View 4 Replies
View Related
Jun 22, 2012
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
View 5 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
View 2 Replies
View Related
Oct 2, 2011
Why does my E1200 forget my Parental Control Password? This happens almost weekly and I have to use the "forgot password" option. It asks my security question, I answer it and set the new password to the same password it keeps forgetting. Why does this happen? Also, is there anyway to have total 24hr control on the Block Internet Access?
View 4 Replies
View Related
Nov 9, 2011
I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies
View Related
Sep 16, 2012
I am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies
View Related
Jul 22, 2012
How can I change default gateway and DNS's for L2TP type of connection? I've tried to specify them in static IP address first and then switched to L2TP as adviced in one forum, but it didn't work. I don't understand why such settings as Gateway and DNS servers cann't be specified as for PPTP connection. Firmware is 2.0.37.
View 1 Replies
View Related
Jan 19, 2012
I'd like to add a WRT54g2 to my LAN. I'd like it to communicate with my existing LAN router, and not to talk directly to the LAN. Therefore, in Basic Setup, I don't have the top part (Internet Setup) configured. Is that a mistake?But, it seems that when I enable DHCP, it hands out its own IP as gateway, and then doesn't seem to send the traffic on upstream. When I configure clients manually with the real router IP, they work fine.
So, I'd like, I guess, Linksys to forward traffic on a static route to real router. How do I do this? Adding a route to real router yields the error, "maybe default route already exists."
View 4 Replies
View Related
Nov 21, 2012
We were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:
-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).
View 1 Replies
View Related
Jan 25, 2012
I have a win 7 netbook that I recently got and for some reason it suddenly cannot keep a connection to the internet. It used to keep a connection before but now I keep getting the error the default gateway is not available about every ten minutes while connected which of course is very frustrating.
I've tried updating all associated drivers but apparently that hasn't changed anything. I've tried restarting the computer and tried different connections. I know its nothing to do with the internet connection I'm trying to connect to as other devices are able to keep a connection with no issue.
View 1 Replies
View Related
Feb 25, 2013
What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies
View Related
Oct 7, 2012
Wireless is working on one laptop but not the other. Default gateway not showing when running command prompt, ipconfig /all
View 5 Replies
View Related
Jan 4, 2011
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Mar 28, 2012
Is it possible to use an E1200 as an access point? I am connecting it to an SE2500..
View 1 Replies
View Related
Jul 11, 2012
I am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies
View Related
Nov 29, 2012
I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
View 6 Replies
View Related
May 15, 2012
I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies
View Related
Nov 30, 2012
I have a Linksys E1200 router.My problem is I have installed a camera system that allows remote viewing.I cannot access the system through the E1200 I am not very knowledgeable in net working.What do I need to do to access the DVR from a remote computer?
View 1 Replies
View Related
Jul 12, 2012
Trying all week to get my E1200 setup as an Access Point with my AT&T U-Verse 2WIRE Modem. [code] It just never seems to work correctly. It will connect for a second or 2 and then jam up. My ultimate scenario would be to have the E1200 just act as a wireless access point and have the 2WIRE do the rest: firewall, DCHP, etc.
View 9 Replies
View Related
Jan 26, 2012
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies
View Related
May 8, 2011
Basically, I'm using a broadband modem, which appears to be connecting fine, with all the required lights being on. My ISP says that, from their end, everything is perfect. Even my laptop shows Local Area Network as connected.However, for some reason, I am not able to access the internet. I was able to use it till last evening, but suddenly the internet stopped working. On Google Chrome, it says that there is no DNS or something.Subsequently, when I tried to access my modem settings, it shows as 'webpage not available'. I then noticed that there is no default gateway! I was able to access it the day before, but now I can't.
View 10 Replies
View Related
Jan 17, 2013
I have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies
View Related
Jan 3, 2013
I wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies
View Related
Oct 14, 2011
I had recently purchased the E1200 router. For some reason, my internet keeps going in and out of service. I will be playing an online game but get disconnected from the server every 6-8 seconds. I tested if it could be my internet provider, but when I connect via Ethernet cord to my modem, it works great. If I run the Ethernet through my router or try wireless connections, it tends to go in and out. It only seems to do this some of the times.
View 1 Replies
View Related
Oct 26, 2012
I have E1200 wireless router and it was working nicely for the whole last year with 2 mac laptops hooked up on it. About 2 months ago there were 1 mac,1 win laptop and a network printer. And again, it was working just fine at the beginning. I'm not sure when exactly it happened first, but now after working couple of hours internet gets off and router stops responding. If I try to reconnect to it from my laptop I just see an error message saying something about "Connection timeout". Also I don't know does it have something to do with the network printer, btw it's connected to the router via ethernet cable not wireless. Anyway, the only solution I've found so far is power off the router for a couple of secs and power it on again, which is obviously not a solution at all, it's annoying and not practical. The time it works fine before it dies is also not fixed, it might be even 10 hrs of working and sometimes only 1-2 hrs. My other suspicion is firmware. I upgraded it almost at the same time when new laptop and printer showed up. Maybe I have to downgrade it, but I couldn't find older version of it. It was HW v. 1, SW v.1.0.00, and now it's HW v.1, SW v.1.0.03.
View 1 Replies
View Related
Aug 12, 2012
I just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies
View Related
