Linksys Wireless Router :: Can't Set Default Gateway On WRT310N In Access Point
Jul 28, 2011
I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies
ADVERTISEMENT
Sep 5, 2011
I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies
View Related
May 26, 2011
My internet provider is telus and they gave me a modem/router combo model VA-G3810bn/tl and another router a linksys wrt310n and i want to by pass the router built into the modem so my linksys will put out a signal instead as it is faster connection any im using windows seven and mozilla firefox if that matters
View 1 Replies
View Related
Nov 11, 2011
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies
View Related
Sep 5, 2011
I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 by an ethernet cable if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible
View 5 Replies
View Related
Aug 31, 2009
I have an EnGenius AP (EOC-2610) I want to connect to my primary router (WRT310N) to extend my network. how I must setup the WRT310N (and maybe the EnGenius) to make it all work together ?
Is the AP's IP should be static ? ie 192.168.1.2 (next to main router's IP)or should it be static in the the primary's DHCP range ? ie 192.168.1.101 or should it be dynamic the IP given by the primary router ?
View 3 Replies
View Related
Apr 27, 2013
I recently purchased and installed seven WAP300N access points in a school, but they are now having intermittent problems with network access, as of right now their network is completely unusable. Specifically there appears to be a conflict between these access points and the gateway/router which provides their network clients with addresses via DHCP; BUT in the three years I have been assisting them the DHCP server on their Cisco router has never before given any problems!
All WAP300N units are wired to the network acting as standard access points and setup to pickup their address automatically via DHCP. When the problem first arose I changed to offending unit to use a static IP address to avoid what I presumed was an address conflict; however the same problem now appears to be happening with the other units as well!
My understanding is that these WAP300N units do not have any in-built DHCP server capability, is this correct ?If not, how I can disable this feature.Otherwise, it would seem to me that the units must be incorrectly using the default gateway address which they are getting from the DHCP server as thier own IP address. Unfortunately assigning static IPs to each access point is not possible as these are controlled by another group and the existing allocation is now used up.
View 5 Replies
View Related
Nov 9, 2011
I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies
View Related
Sep 16, 2012
I am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies
View Related
Jul 22, 2012
How can I change default gateway and DNS's for L2TP type of connection? I've tried to specify them in static IP address first and then switched to L2TP as adviced in one forum, but it didn't work. I don't understand why such settings as Gateway and DNS servers cann't be specified as for PPTP connection. Firmware is 2.0.37.
View 1 Replies
View Related
Feb 9, 2009
I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address.
View 2 Replies
View Related
Jan 19, 2012
I'd like to add a WRT54g2 to my LAN. I'd like it to communicate with my existing LAN router, and not to talk directly to the LAN. Therefore, in Basic Setup, I don't have the top part (Internet Setup) configured. Is that a mistake?But, it seems that when I enable DHCP, it hands out its own IP as gateway, and then doesn't seem to send the traffic on upstream. When I configure clients manually with the real router IP, they work fine.
So, I'd like, I guess, Linksys to forward traffic on a static route to real router. How do I do this? Adding a route to real router yields the error, "maybe default route already exists."
View 4 Replies
View Related
Nov 21, 2012
We were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:
-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).
View 1 Replies
View Related
May 4, 2012
I cant seem to to connect to my nintendo i have a motorala surfboard SBG6580
View 1 Replies
View Related
Aug 19, 2011
My WRT310N linksys wireless router has recently stopped permitting internet access to devices connected to it, both wired and wirelessly. I have connected my broadband modem directly to a single computer (which is how I am posting this) and evidently there is nothing wrong with my internet service. I have tried restarting my modem, the router, and the computers I am trying to access the internet with, and it has not worked. Note that local communications work fine, I was able to ping another device connected to the router, and even establish a TCP connection.It is possible that the settings on the router have been changed without my knowledge, if so, however, I do not know which setting could be causing this.
View 1 Replies
View Related
Sep 20, 2011
We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.
View 2 Replies
View Related
Jan 24, 2013
I reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies
View Related
Mar 16, 2011
I switched to comcast internet recently and got a new modem. The modem is the telephony Arris one, but the problem is that I already have a Motorola SBG6580 but can not use that for my wireless laptop options. I want to be able to use the SBG6580 as my access point and LAN, but it isn't allowed any internet to share wirelessly?
View 3 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Jul 11, 2012
I am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it. When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need port forwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2.
View 3 Replies
View Related
Jun 18, 2011
I have a pocket wifi which allows you to connect up to five devices. my mum, sister and my phone can access it no problems but my laptop wont work.what will happen is:
- it connects automatically to the wifi
- but it has a little error mark on it
- and it says theres no internet access.
ive tried everything, ive ran several windows network diagnostics and it says the problem is the default gateway being unavailable.
View 4 Replies
View Related
Jan 13, 2013
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies
View Related
Oct 5, 2011
I just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies
View Related
Jul 31, 2012
i am using a tp link 8817 modem, i can go online normaly but i can not access the default gateway (192.168.1.1, i check it in cmd/ipconfig) it keeps asking me username and password, althought i filled them with the correct username and password.
View 2 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
View 2 Replies
View Related
Nov 19, 2011
I need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
View 8 Replies
View Related
Jun 28, 2011
ASA 8.3(2) 5505
I've configured a number of remote access vpns on ASAs, but I don't recall having a default gateway setting assigned after logging in.
Is there a way to disable the assignment of a default gateway upon login?
The value assigned is meaningless. It's just the next available address in the local pool.
View 2 Replies
View Related
Jul 18, 2006
I'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies
View Related
Dec 6, 2012
How to connect my att dsl westell moden to my Linksys router. I am changing service providers from comcast to att. My router was working with my cable model but I'm unable to configure it to communicate with the dsl modem.
View 9 Replies
View Related
Apr 28, 2012
I have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?
View 1 Replies
View Related
Feb 5, 2012
I am getting 22-30mbs down through my router wired and I'm only getting about half of that through wireless. Is this normal? I also have a question about the color of the internet led. The online manual says that it should be blue, but mine is green. All of the other LEDs are blue except the internet one. Not sure if that is an issue or not.
View 1 Replies
View Related
Sep 17, 2012
our WRT310N router does not retain any configuration given to it. When we reset the device, it goes back to its factory settings. In that state we can access the device (http://192.168.1.1), make some changes and save it. The changes include giving it a different name from the default, and setting a password for the connection. However, when we try to use it for our wireless network, we cannot connect to the internet. Checking the Connection Status in a Windows XP laptop, we found out that we have been given a gateway different from what we have set the device into and thus a different set of IP addresses for each of the device.
Also at this time, we cannot access the router anymore (via 192.168.1.1 or via the gateway provided) and thus having no choice but to reset the device again. We then reinput the configuration desired, save it, restart the systems (both PCs and router) but after a few moments (initially it retains the settings chosen) we won't be able to connect through the Internet and find out that the router has a different configuration again. We also tried letting the device "rest" but the same problem persists.
View 5 Replies
View Related
