ASA 8.3(2) 5505
I've configured a number of remote access vpns on ASAs, but I don't recall having a default gateway setting assigned after logging in.
Is there a way to disable the assignment of a default gateway upon login?
The value assigned is meaningless. It's just the next available address in the local pool.
A customer got a new VoIP PBX, and now I have to forward port 443 on the ASA to the PBX for remote administration purposes. The LAN-interface of the PBX is in the same subnet as the ASA but has an external VoIP-router as default gateway and not our ASA. Is it even possible to forward the port to the PBX when there is no route of any sort to our ASA on it?
View 2 Replies View RelatedAs shown in the diagram below, I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pcs at remote offices has IP communication with the server from the central office using a static route.Does the solution would be to put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network?
View 3 Replies View RelatedI have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc's at remote offices has IP communication with the server from the central office using a static route. put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network? I had thought to use RSV400 routers?
View 6 Replies View RelatedI am trying to get rid of 2 old 2651xm's and 2 2950's from my CCNA days and want to get into the ASA realm. Can I be able to use the ASA, not only as a security appliance / firewall, but also be able to write the access lists, etc, to be able to use this as my router to push packets to and from my internal LAN to the outside world? I guess I should have stated as this being the front end device to my network, just after my DSL Cable modem, that is..and being the only device. I am trying to have this as my main router /firewall solution and then I have an old Linksys router I will pipe off one of the L2 ports to have an AP for my wireless devices? Is this a real solution an ASA can provide?
View 2 Replies View RelatedI have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
How do I enable remote access to ASDM from outside of the network on the ASA 5505? This would be used for remote access to the firewall at a site that is not utilizing VPN.
View 5 Replies View RelatedI would like to allow remote access to a windows server through a ASA (5505) firewall. Users will use the vpn connection in order to connect to a private network. Is there any link that describes the steps for ASDM?
View 3 Replies View RelatedI want to give access to remote subnet on firewall 5505.
Remote subnet is 16x.15X.56.0
Here is my access list
access-list outside_5_cryptomap extended permit ip 192.168.12.0 255.255.254.0 16x.15X.56.0 255.255.254.0
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable. [code]
View 1 Replies View RelatedI am proposing Remote access VPN solution to my client as per the attached diagram. However they are required IPS solution as well.
So in this case i dont think i can implement the IPS with outside interface in inline mode because of the encrypted traffic. Is it feasible if i enable IPS with inside interfce ?
After getting hacked I want to limit terminal server/ remote desktop to only my computer. (although I may need to let other net in later)
In other words I want only computers from my home ip range (lets say my ISP gives me at home something in 28.28.XX.0) to be let in to the router at work and then to port 3389.
In the work ASA 5505 softwareVersion 7.2(4) I now have:
access-list outside_in extended permit tcp any interface outside eq 3389
static (inside, outside) tcp interface 3389 192.168.1.2 3389 netmask 255.255.255.255
acces-group outside_in in interface outside
I am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedI am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies View RelatedI am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it. When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need port forwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2.
View 3 Replies View RelatedI have a pocket wifi which allows you to connect up to five devices. my mum, sister and my phone can access it no problems but my laptop wont work.what will happen is:
- it connects automatically to the wifi
- but it has a little error mark on it
- and it says theres no internet access.
ive tried everything, ive ran several windows network diagnostics and it says the problem is the default gateway being unavailable.
I just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies View Relatedi am using a tp link 8817 modem, i can go online normaly but i can not access the default gateway (192.168.1.1, i check it in cmd/ipconfig) it keeps asking me username and password, althought i filled them with the correct username and password.
View 2 Replies View RelatedCurrently a network consists of two subnets, one subnet is behind a ASA and the other behind a PIX, both connecting to the ISP's routers. If the PIX is retired, is it possible to create/consolidate the two networks protected by the ASA5510 with the default gateway being the ISP?
How can two private networks be protected by the ASA5510? One conceptual way is to create the VLANS on a layer 3 switch, on the "inside" interface of the ASA. In this senario what would the "inside" network's IP address? If the above is possible, how would natting occur?
Is there an efficient configuration to protect two networks protected by the 5510, other than creating a DMZ?
Is it possible to create two private networks with same level of security, 100 on a three network interface connections?
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies View RelatedWe have a 3560 switch behind a ASA 5510 at a site that we are trying to access via telnet over the internet, we find out the switch does not have a default gateway configured. So I configure the following rule on the 5510: [code] Try accessing the switch, and all is good. One of our change control steps is to identify any others are connected to the device via: [code] I see the connection and show users command return 172.16.30.15, as expected. How is it possible that address can connect to that switch.
View 7 Replies View RelatedI've configured a VPN IPSEC on my ASA5510. It Assigned IP/NETMASK/Gateway via a DHCP Server on the LAN.The problem is that when a client is connected to the VPN , it takes the right IP and NETMASK. ( 192.168.1.109 / 255.255.255.0) but the Default Gateway is wrong ( 192.168.1.1). It should be the default Gateway of my LAN router ( 192.168.1.229).
View 7 Replies View RelatedI am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
I need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
View 8 Replies View RelatedI am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies View RelatedI have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedI've recently installed a new WRT610N router onto my small business network. Previously my network was as follows: Modem - Server - LAN where the server acts as a gateway using routing and remote access.
The addition to the setup now has the router between the modem and the server itself. After configuring everything - and DISABLING the router firewall and as last resort opening the server to the DMZ i'm having serious issues opening specific ports but not others.
To be specific - the server is sitting in the DMZ open right now. In my routing and remote access any port that I have being forwarded over to another computer is open from the internet with no issues. The problem lies with ports that need to be opened on the server itself with 127.0.0.1 where i'm getting a "connection timed out" from canyouseeme.org.
Why the local opening of ports is having issue? Before the router was installed everything worked great - however the router is needed for wifi and it cannot be configured as an access point only.
What is the factory default config on ASA5505 with 8.4.1?
View 3 Replies View RelatedI was under the impression that all Cisco ASA firewalls shipped with a default inspection policy.
Example
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
[Code]......
can I build this myself? Why is it missing (I have two other ASA 5505s here that also do not have it). What would I do to rebuild it?
i have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedCISCO ASA 5505
Interfaces:
OUTSIDE - 194.50.90.221 255.255.255.0 / security level 0
DMZ - 192.168.12.254 255.255.255.0 / security level 25
INSIDE - 192.168.0.6 255.255.255.0 / security level 50
Now, if I want to ping from the DMZ to INSIDE, I get an error message "no translation group found for icmp src DMZ: ...... dst: INSIDE...."
I fixed is by adding "NAT 0" onto the INSIDE interface so that packets originating from "INSIDE" that are destined for "DMZ" do not get NAT'd.
Now my question is, becasue these are all directly connected networks, how come the firewall does not route the packets, but tries to NAT them instead.
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View RelatedI've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.