RSV400 Router / Using Default Gateway On A Vpn Remote Side?
Oct 17, 2011
I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc's at remote offices has IP communication with the server from the central office using a static route. put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network? I had thought to use RSV400 routers?
View 6 Replies
ADVERTISEMENT
Oct 17, 2011
As shown in the diagram below, I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pcs at remote offices has IP communication with the server from the central office using a static route.Does the solution would be to put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network?
View 3 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Jun 28, 2011
ASA 8.3(2) 5505
I've configured a number of remote access vpns on ASAs, but I don't recall having a default gateway setting assigned after logging in.
Is there a way to disable the assignment of a default gateway upon login?
The value assigned is meaningless. It's just the next available address in the local pool.
View 2 Replies
View Related
Jan 30, 2013
My E1500 enters a state where the LAN-side (broadcast, etc.) works, but the WAN-side (internet connection) just goes away. If I go unplug and replug the E1500 the internet connectivity comes back.When this happens, the wireless indicator on my desktop (Dell with Intel wifi) says I have an internet connection, but I clearly don't.
View 2 Replies
View Related
Feb 22, 2013
I just purchased a Buffalo WZR-600DHP router and have been having a weird issue. When using the router on the shipped DD-WRT firmware I consistently get "The default gateway is not available" error and I have to reset my wireless adapter on my laptop. This issue doesn't occur on my hardwired desktop or interestingly enough when the Buffalo router was switched to the "user-friendly" firmware the issue didn't occur either. Both times the router was on the DD-WRT firmware I've had the default gateway issue.
View 1 Replies
View Related
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Oct 25, 2012
hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies
View Related
Nov 9, 2011
I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies
View Related
Sep 16, 2012
I am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies
View Related
Feb 23, 2012
We want to use cisco 3845 and pick up IPSec, with remote side. But I am afraid that cisco 3845 can't handle 155 Mbits over IPsec. We will buy AIM- VPN/ SSL3 card. Is this sufficient?
View 3 Replies
View Related
Oct 24, 2011
about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies
View Related
Jul 22, 2012
How can I change default gateway and DNS's for L2TP type of connection? I've tried to specify them in static IP address first and then switched to L2TP as adviced in one forum, but it didn't work. I don't understand why such settings as Gateway and DNS servers cann't be specified as for PPTP connection. Firmware is 2.0.37.
View 1 Replies
View Related
May 21, 2013
Does ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
View 1 Replies
View Related
Aug 1, 2011
I have a 2511 TS linked into my CCNP lab and configured it with default gateway pointing to my ADSL router. The TS has a staic local IP in my LAN also I have port forwarding set up on my ADSL router to direct all Telnet (not cofigured for ssh yet) sessions to the TS.
The TS is linked to the ADSL router via the transceiver module ( CentreCom AT-210TS) which feeds the ADSL router with ethernet connection.I have tried to access the TS from a remote location but with no joy, fortunately I also have it consoled to my PC so I SSH to the PC and then run my terminal emulator from there. Using SSH to the PC and then minicom to the TS when doe this way (Remote Location>Ubuntu>minicom>TS) I can see the ethernet interface has no MAC address when i do a sh internet eth 0 mac is set to 0000.0000.0000.
I don't want to be connecting via ssh to PC before accessing the TS but instead just want to connect to the TS; for the life of me I still can't explain what's going on.
View 1 Replies
View Related
Nov 6, 2012
So network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.
And just for an example this is what I get if I use DHCP:
IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1
And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?
View 3 Replies
View Related
Jan 19, 2012
I'd like to add a WRT54g2 to my LAN. I'd like it to communicate with my existing LAN router, and not to talk directly to the LAN. Therefore, in Basic Setup, I don't have the top part (Internet Setup) configured. Is that a mistake?But, it seems that when I enable DHCP, it hands out its own IP as gateway, and then doesn't seem to send the traffic on upstream. When I configure clients manually with the real router IP, they work fine.
So, I'd like, I guess, Linksys to forward traffic on a static route to real router. How do I do this? Adding a route to real router yields the error, "maybe default route already exists."
View 4 Replies
View Related
Jul 28, 2011
I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Nov 21, 2012
We were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:
-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).
View 1 Replies
View Related
Nov 11, 2011
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies
View Related
Feb 23, 2013
I would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
View 4 Replies
View Related
Oct 12, 2011
Loss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies
View Related
May 21, 2012
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
View 15 Replies
View Related
Mar 13, 2013
i configured cisco asa 5520 as cisco ezvpn server and cisco 891 as ezvpn client .the configurtion is working fine.i am using client mode on the ezvpn client side.but my quesion is , is it possible to communicate to ezvpn client side internal ip from the ezvpn server side?and one more thing what is the benefit of network extension mode on the client side and how it will work what are possible changes need to do in the server and the client side.
View 4 Replies
View Related
Mar 17, 2013
I'm trying to setup an ASA and a UC540 side by side, to utilize the ASA for data networking and the UC540 for voice. This 'should' work fine, I just seem to be having an issue where the ASA seems to be blocking traffic from the voice network as it passes through.So here is the LAN setup:ASA: 1.1.1.1UC540: 1.1.1.2The UC has a voice vlan 10.1.1.1/24 and a service module at 10.1.10.1/30My PC uses the ASA as its default gateway, 1.1.1.1The ASA then has static routes to the UC networksRoute 10.1.1.1/24 1.1.1.2Route 10.1.10.1/30 1.1.1.2Ping from PC to the UC networks works fine. However, ping from the UC networks to PC fails. ASA logs show traffic being denied due to not having an established connection or something.My guess is that the traffic is being blocked because the egress and ingress paths are different? Traffic from the PC goes to the ASA, then gets routed to the UC and it works. However in the other direction, traffic from the UC is going directly to the PC and bypassing the ASA, because its a directly connected network and doesn't have to route through the ASA to get to the PC. The reply traffic from the PC DOES go through the ASA following its route table, thus the issue of the ASA not seeing the established connection?Same-security inter and intra interface is enabled.So I think I see the issue, I just don't know how to fix it. Is there something I can configure on the ASA to allow for this? My only other option would be to configure a /30 on a new vlan to handle the routing between the UC and ASA or something, but that seems like its going to make this simple setup way too complicated with extra networks, vlans, trunks, etc.I am running ASA version 8.4.5?
View 1 Replies
View Related
Feb 21, 2013
i joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies
View Related
May 3, 2012
Periodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
View 14 Replies
View Related
Nov 30, 2011
I recently got a new laptop and ever since, the internet goes in and out. Most of the time it is not out long enough to display the no connectivity icon or stop music from streaming but it is noticeable. When I run the troubleshooter it says that the default gateway is unavailable. I tried manually setting the connection information but the same thing keeps happening except the troubleshooter then says that DHCP is not enabled. I've disabled every firewall I can find and updated all the drivers available. Here is my info:[CODE]
View 3 Replies
View Related
Jan 3, 2011
When I plug my laptop up to our modem, all i get is local access. IPconfig gives me to default gateway or dns suffix. Naturally there is no wireless. My roomates laptop runs fine wired or not and we have the same set up.Not sure what to do.
View 12 Replies
View Related
Feb 8, 2013
I am having issues playing certain games on my ps3. So I've been searching for solutions and I came across a video that wanted me to go to run/cmd/ipconfig. I have little knowledge of computers but I'm not sure that what my ipconfig is showing is supposed to be there. At first I googled and learned about ipv6 addresses because i found that weird but i think that checks out fine. I then googled about the weird numbers and letters in my default gateway and came up empty. Is there a reason thats there?
View 3 Replies
View Related
Jan 2, 2011
I have Squid proxy installed on a ubuntu box here. Currently all my PC's use my ADSL modem as their default gateway but what i wanted to do was see if it was possible to use the ubuntu box as the default gateway, and have it route through Squid to my ADSL modem.
View 3 Replies
View Related
May 20, 2011
I am trying to change the password on my D-Link router. So i typed ipconfig into cmd and the default gateway i get is 169.234.95.I have tried what used to work at home such as 192.168.0.1 and all of those.
View 9 Replies
View Related
