Linksys Wireless Router :: E4200 - L2TP Default Gateway?

Jul 22, 2012

How can I change default gateway and DNS's for L2TP type of connection? I've tried to specify them in static IP address first and then switched to L2TP as adviced in one forum, but it didn't work. I don't understand why such settings as Gateway and DNS servers cann't be specified as for PPTP connection. Firmware is 2.0.37.

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: What Is Maximal Speed For E4200 L2tp Protocol

Oct 15, 2011

What Is Maximal Speed For E4200 l2tp Protocol.

View 1 Replies View Related

Linksys Wireless Router :: Default Gateway 0.0.0.0 With WRT54GX2

Nov 9, 2011

I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.

View 3 Replies View Related

Linksys Wireless Router :: E900 - Default Gateway Not Available

Sep 16, 2012

I am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.

View 2 Replies View Related

Linksys Wireless Router :: WRT54g2 Handing Out Wrong Default Gateway

Jan 19, 2012

I'd like to add a WRT54g2 to my LAN. I'd like it to communicate with my existing LAN router, and not to talk directly to the LAN. Therefore, in Basic Setup, I don't have the top part (Internet Setup) configured. Is that a mistake?But, it seems that when I enable DHCP, it hands out its own IP as gateway, and then doesn't seem to send the traffic on upstream. When I configure clients manually with the real router IP, they work fine.
 
So, I'd like, I guess, Linksys to forward traffic on a static route to real router. How do I do this? Adding a route to real router yields the error, "maybe default route already exists."

View 4 Replies View Related

Linksys Wireless Router :: Can't Set Default Gateway On WRT310N In Access Point

Jul 28, 2011

I am using a WRT310N.  I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N.  So I just plug the LAN port on the WRT310N directly to my LAN switch.  I just need the WRT310N to have an IP address for management.  So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN.  You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Version 2 Weird Default Gateway

Nov 21, 2012

We were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:

-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).

View 1 Replies View Related

Linksys Wireless Router :: E1200 Do Not Have Internet Access As Default Gateway

Nov 11, 2011

I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?

View 4 Replies View Related

Linksys Wireless Router :: E4200 - Cannot Connect To Default GW 192.168.1.1

Apr 15, 2013

I've noticed that my 192.168.1.1 login console was slow loading up on my E4200 V1. The router functioned just fine(wireless and wired). These past few days I tried to log in to set some DNS settings and I cannot access 192.168.1.1.I have tried via wireless and wired. The router powers on still seems to function but won't allow me to load up the admin console page.To my last resort, I held in the tiny reset button and the router seems to have went back to it's default settings (SSID = Cisco#####) but I cannot connect to it. what I can try to get back into the management window.I was able to manage everything from my laptop about a month ago or so, but now I can't do anything.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Reset To Factory Default

Nov 26, 2012

Due to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset.  After then, I could not access the router via browser with 192.168.1.1 at URL entry.  My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss.  So router was restored with 192.168.1.1 and cable connection was OK.

View 2 Replies View Related

Linksys Wireless Router :: E4200 On Comcast Business Account That Uses Gateway

Jul 23, 2011

I am setting up a e4200 wireless router on a Comcast business account that uses a gateway (SMC8014).I have fixed public IP [x.x.x.x/30] and the gateway sets up a subnet 10.1.10.0 (255.255.255.0).  I have mail server and DNS server at 10.1.10.20 and I use port forwarding in the SMC gateway. 
 
The setup of the e4200 using the software sets up a network (192.168.1.1).  I can connect devices to the router and browse the external Internet.  However, when my android phone connects to the e4200 it gets an IP such as 192.168.1.101.  However, I cannot download my mail which is at 10.1.10.20.  When I try to browse that IP from the android phone I get the SMC gateway at 10.1.10.1 and not the computer at 10.1.10.20.  If was coming in from the external Internet port forwarding would take over but it does not work for the android phone connected to the e4200.
 
Also, i noticed that when I set up the default setup for the e4200 the "Cisco Connect" says the WAN address is 10.1.10.155 and the LAN address is 192.168.1.1.  However, when I go to the SMC Gateway and list the connected computers it doesn't see the e4200 at 10.1.10.155.  If I set up the e4200 within 10.1.10.0 then the SMC sees it (but the computer name always says "unknown").  It I set the DHCP in either the SMC or the e4200 within the 10.1.10.0 subnet I can see the phone connection in the SMC when I list the connections but any requests to 10,1,10.0 computers goes to the SMC gateway.

View 5 Replies View Related

Linksys Wireless Router :: E4200 / Benefit To Enable HTTPS Within GUI Instead Of Using Default HTTP?

Mar 16, 2013

Any benefit to enable https with in the gui instead of using the default http?

View 1 Replies View Related

Linksys Wired Router :: Can't Set RV016 To Assign A Default Gateway IP Of Server

Jun 22, 2011

I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)

View 1 Replies View Related

Cisco Routers :: L2TP On SRP541W Default Routing Table Is Wrong

Sep 21, 2011

I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
 
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...

View 3 Replies View Related

Linksys E4200 Cannot Connect To Default GW

Apr 13, 2013

I've noticed that my 192.168.1.1 login console was slow loading up on my E4200 V1. The router functioned just fine(wireless and wired). These past few days I tried to log in to set some DNS settings and I cannot access 192.168.1.1.

I have tried via wireless and wired. The router powers on still seems to function but won't allow me to load up the admin console page.

To my last resort, I held in the tiny reset button and the router seems to have went back to it's default settings (SSID = Cisco#####) but I cannot connect to it.

What I can try to get back into the management window.

I was able to manage everything from my laptop about a month ago or so, but now I can't do anything.

View 1 Replies View Related

Linksys Wireless Router :: WRT54GL - Specify L2TP Server By Domain Name?

Mar 28, 2013

I have WRT54GL v1.1 with last firmware. How to specify L2TP server by domain name? I see only fields for IP.

View 4 Replies View Related

Linksys Wireless Router :: Wrt160n V3 Slow Connection On L2tp?

Apr 10, 2012

I have speed 12M when I connect wrt160n v3 through l2tp, my speed down to 4M-5M. When i connect modem directly to computer I get speed 12M.

View 1 Replies View Related

Linksys Wireless Router :: EA4500 L2TP Dual Access?

Jun 25, 2012

Do you plan to support L2TP protocols Dual access.and / or the ability to enter static ip address (as in pptp) to connect l2tp.in Russia in the past few years,dominated by the type of connection L2TP Dual access, ie provider gives the internal ip address (static), and address of the VPN DNS server. to access the Internet using a protocol l2tp.as the network provider has the internal resources, which can be accessed if the router supports dual atstsess.of the protocol pptp providers moving away.

View 3 Replies View Related

Default Gateway Is Not Available With Buffalo WZR-600DHP Router

Feb 22, 2013

I just purchased a Buffalo WZR-600DHP router and have been having a weird issue. When using the router on the shipped DD-WRT firmware I consistently get "The default gateway is not available" error and I have to reset my wireless adapter on my laptop. This issue doesn't occur on my hardwired desktop or interestingly enough when the Buffalo router was switched to the "user-friendly" firmware the issue didn't occur either. Both times the router was on the DD-WRT firmware I've had the default gateway issue.

View 1 Replies View Related

Wifi Router Not Assigning Ip Address Or Default Gateway?

Oct 25, 2012

hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID

View 8 Replies View Related

RSV400 Router / Using Default Gateway On A Vpn Remote Side?

Oct 17, 2011

I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc's at remote offices has IP communication with the server from the central office using a static route. put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network? I had thought to use RSV400 routers?

View 6 Replies View Related

Netgear N600 Router - Unable To Ping Default Gateway

Oct 24, 2011

about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1

View 2 Replies View Related

Cisco WAN :: Does IP Default-gateway Have Any Effect On L3 Device Such As 2811 Router

May 21, 2013

Does ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
 
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.

View 1 Replies View Related

Cisco WAN :: 2511 Default Gateway Pointing To ADSL Router

Aug 1, 2011

I have a 2511 TS linked into my CCNP lab and configured it with default gateway pointing to my ADSL router. The TS has a staic local IP in my LAN also I have port forwarding set up on my ADSL router to direct all Telnet (not cofigured for ssh yet)  sessions to the TS.
 
The TS is linked to the ADSL router via the transceiver module ( CentreCom AT-210TS) which feeds the ADSL router with ethernet connection.I have tried to access the TS from a remote location but with no joy, fortunately I also have it consoled to my PC so I SSH to the PC and then run my terminal emulator from there.  Using SSH to the PC and then minicom to the TS when doe this way (Remote Location>Ubuntu>minicom>TS) I can see the ethernet interface has no MAC address when i do  a sh internet eth 0 mac is set to 0000.0000.0000.
 
I don't want to be connecting via ssh to PC before accessing the TS but instead just want to connect to the TS; for the life of me I still can't explain what's going on.

View 1 Replies View Related

Modem And Router (D-Link DIR-601) DHCP Giving Out Wrong Default Gateway

Nov 6, 2012

So network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.

And just for an example this is what I get if I use DHCP:

IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1

And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?

View 3 Replies View Related

Cisco WAN :: DPC3825 Shouldn't Default Gateway IP Have Same Mac Address As Computer / Router

Feb 23, 2013

I would like to know what ip addresses I should see in this  table. Shouldn't my default gateway IP have the same mac address as my  computer or router? There are 2 different ip address/mac addresses from  different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.

View 4 Replies View Related

Default Gateway Is Not Available With Wireless Network Adapter

Dec 1, 2012

My computer will only run on ethernet cable, the network can be found but only connects for a second, connects to the internet in and out, it gives the error, default gateway is not available, or problem with the wireless network adapter. The manufacturer is HP

Windows IP Configuration

Host Name . . . . . . . . . . . . : Owner-HP
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : cogeco.net

[code]...

View 3 Replies View Related

Wireless Repeater Setup - No Default Gateway

Dec 2, 2012

So i am trying to Set up a wireless repeater so i can have a better signal in my back yard but i could not set the configurations for my repeater because the gateway (ip address? Not really sure what it is called) would not work when i entered it into the browser. So i went into command prompt to make sure i had the right gateway and it did not even exist.

View 6 Replies View Related

Wireless Connection Keeps Dropping - Default Gateway Is Not Available?

Jan 22, 2012

My wireless connection keeps dropping. It tells me the default gateway is not available.I have tried to check and do the things told here first but not working have tried to do the driver update . I have a realtek driver, there is no update available for it.I have a 25 mbit connection i barely get 1 mbit.Extremely slow The laptop is running windows 7 .Also i already did all the TCP/IP stack repair options like winsock reset etc.The antivirus i am running is ESET Nod32 version 4 i think .I have attached a xirrus wifi inspector photo if u want to look at it.[CODE]

View 5 Replies View Related

Wireless Hardware Disabled - Default Gateway Is Not Available?

Jul 28, 2011

I cannot connect to the internet on my laptop using wireless. It was working fine for a while and it just stopped. This is not the first time this has happened. Although i cannot remember if i caused it to start working again. My laptop wireless hardware has disabled itself. I've tried enabling/disabling and troubleshooting from what i know how to do but its still not working. This problem started yesterday.

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, Intel64 Family 6 Model

[Code].....

View 12 Replies View Related

Cisco WAN :: RV016 Router - Logging / Ping Default Gateway Fail On Ixp1?

Oct 12, 2011

Loss connection every day for several hours and just comes back.  Reset router than works fine.  Only about six months old.  Found several forums staing the same problem.  I have a RV016 16 port VPN router.  What can I do? 

View 1 Replies View Related

Cisco Switching/Routing :: Default Gateway Of VOICE Providers 2600 Router

May 21, 2012

We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too. 

At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites. 
Testing
 
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps? 

View 15 Replies View Related

Cannot Hold A Wireless Internet Connection (default Gateway Not Available)

Jan 25, 2012

I have a win 7 netbook that I recently got and for some reason it suddenly cannot keep a connection to the internet. It used to keep a connection before but now I keep getting the error the default gateway is not available about every ten minutes while connected which of course is very frustrating.

I've tried updating all associated drivers but apparently that hasn't changed anything. I've tried restarting the computer and tried different connections. I know its nothing to do with the internet connection I'm trying to connect to as other devices are able to keep a connection with no issue.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved