about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies View RelatedLoss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies View RelatedI have a VM server, whose IP is in customer VLAN600 ( 172.60.60.10/24 ) and Peer end is switch then Firewall.Switch is configured with same VLAN600 and learning mac-address of Server on VLAN 600, Firewall is also having VLAN600 and IP is 172.60.60.1/24.Server is not able to Ping/reach Firewall and vice versa.
View 1 Replies View Relatedi'm having problem to ping succesfully default gateway on Router1 from Router2. Basically i can: - ping from R1 the serial interface on R2 and default gateway on R2 - telnet from R1 to R2 - ping from R2 to serial link on R1, BUT I CANNOT ping default gateway from R2 to R1 Below is the photo showing topology and running configuration on both routers
View 2 Replies View RelatedWhat is the default gateway so i can password protect my wireless??
View 1 Replies View RelatedI have a actiontec Wireless N ADSL Modem/Router Model# GT784WN & netgear n600 wndr3400v2 router that I would like to setup as a Wireless Repeater. I can not seem to get the netgear n600 setup.
View 1 Replies View RelatedI'm trying to get a 2811 router with a NM-AIR-WLC6 Wireless Controller Module to work with an c1200 series access point. The LWAP is connected to a 2690 switch which has a trunk connected to the router. My configuration looks very similar to example 2 on this page: [URL] . The LWAP does get an IP from the DHCP pool on the router. I can also connect to the GUI of the controller from a PC on VLAN 250 (which also is connected to the switch).
[URL]
The moment I join my Wireless network I get no IP and when I enter a valid static IP, I still can't ping the gateway. I also noticed that the controller could ping the gateway before I configured the interface. After configuring an interface with that gateway, the controller loses the ability to ping to it. I can't seem to figure out why. I've been working all week on getting this controller and LWAP to broadcast a fully working network.
This would probably sound like a stupid question but it took at least 2 hours of my time so far. I have a 3750 switch where a router and a server is connected. From the switch I can ping the router and server with no issue (directely connected). But from the server I am not able to ping the router. The router and the server are in the same subnet. The router is configured as the default router for the server. I am not able to ping the server from the router either. Here's the output of the ip route from the router. The server IP address is 10.1.200.21 and the router IP address is 10.10.200.1
10.0.0.0/8 is variably subnetted, 8 subnets, 3 masks
C 10.1.30.0/24 is directly connected, FastEthernet0/0.30
C 10.1.20.0/24 is directly connected, FastEthernet0/0.20
[Code].....
I used the Cisco Configuration Professional to add an Easy VPN Server to my 3825. I'm able to connect when remote but I can't ping the default gateway of 192.168.1.1 which is in the same network as the VPN DHCP pool. I can access every single other device on the VLAN segments but not the default gateway which means when i connect I can't look at my router. And there's more, I cannot ping anything offnet (ie 75.75.75.75).
Attached are some images which show some details from the client during the VPN connect and a few from the router (i had to use the lan switch as a jump host). If you can figure this out before I go back to the coffee shop to test this tomorrow I will send you a cake.
[code]...
I have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
I have a 3560G and an ASA FW, for which I am trying to use PBR to append the next hop. The gateway is the switch VLAN address and the amended net hop is the same VLAN interface on the ASA. Trouble is, I can ping the FW from a client, but not the switch. If I remove the route map, I can ping both. Even more strange is this is the case for some VLANs, but not all!
Config:
HOST ON VLAN 96
IP 10.11.120.99
S/M 255.255.255.240
[Code].....
I am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies View RelatedMy controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies View RelatedI am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
I'm trying to connect to connect to OpenVPN server from my Ubuntu 11.10 machine. I use the following command to do it (under root user):
openvpn --config /home/vladimir/client.ovpn
Everything seems to be OK, it connects normally without any warnings and errors, but when I try to browse the internet I see that I still use my own IP address, so VPN connection doesn't work. When I run openvpn command, it displays the following message among others:
NOTE: unable to redirect default gateway -- Cannot read current default gateway from system
Below is full output of openvpn command:
[code]....
I'm unable to connect to the internet from my laptop. When I do a diagnostic test it tells me that the default gateway is not available. I've tried resetting it, resetting my IP address via command prompt, restarting the router, etc.
View 10 Replies View RelatedWe have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
We have a WLC 4410 management IP Address configured as 10.40.124.59.and configured VLAN1 on WLC with IP address 10.40.126.250. we are unable to ping the VLAN1 ip address from the switch. even unable to ping 10.40.126.252 (Gateway). Is there any limitation that we can not configured ip address from secondary scope...Switch vlan 1 configuration is ......interface GigabitEthernet0/0.1description Business VLANencapsulation dot1Q 1 nativeip address 100.93.50.2 255.255.0.0 secondaryip address 10.40.126.252 255.255.255.0 secondaryip address 10.40.124.61 255.255.255.192 secondaryip address100.43.94.252 255.255.255.0.
View 3 Replies View RelatedTrying to get my Netgear N600 router to connect to the internet...nothing will get it to connect.I am able to follow step-by-steps to resolve this
View 14 Replies View Relatedhow to wire a netgear n600 to a U-verse router in order to strengthen the wifi signal
View 1 Replies View RelatedMy HP printer finds my network, signs on just fine, has internet. My 2 wired PCs are connected and have internet. My 2 wireless laptops find the network and have internet. Everything has internet successfully thru the router....not one of them can print anything because not one of them can see the printer that I know is there.
View 3 Replies View RelatedI puchased the N600 WNDR3700v3 Dual Band Gigabit Router. I am able to see my wireless account I set up and is out there to connect to, but I cant connect. I can connect with an ethernet cord, but nothing wireless. It doesnt work for my home or work laptops. Prior to this I had another wireless set up and I am tempted to plug that one back in.
View 1 Replies View RelatedJust bought a new Netgear N600 router, hooked up 4 wired computers with no problem and got several wireless devices to hook up without issue. My laptop however, will not give me internet access when accessing the network wirelessly.
The access is labeled as Local Only, and the network is considered unidentified. Signal strength is excellent, and it reads the name of the new wireless server I created. It prompted me to enter the passphrase, which I did, and now my laptop is stuck on local only.
I tried updating my adaptor drivers but they are all up to date, and I tried to enter my adaptor into the address reservation on the router configuration page using the laptops MAC address and IP address.
My son just got an Asus Laptop from his school. It is running Windows 8.It connects to other peoples WIFI, just not my home WIFI.When he got it home he found the network, entered the password and nothing happened. Now it can't even find the network.There is nothing wrong with the router as every other device connects fine.The router is a Netgear n600 - DGND3700?
View 3 Replies View RelatedI have a netgear n600 router and in the room its in i get around 50 down and 12 up but in other rooms it drops significantly(the highest ive gotten is 11 down in other rooms). is there any setting i can go into.
View 3 Replies View Related[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies View RelatedI tried using an ethernet cable (cat 6) to connect my laptop (Sony VPC-1190X) to our gigbit router (Netgear N600 WNDR3800), but I get a message that there is no internet connectivity and the light representing that port on the router does not turn on.So, dead ethernet port on the router? Nope - unplugged the working printer from the router and used that ethernet port - same result.so dead ethernet port on the laptop? Nope - plugged the laptop into a gigbit switch (D-link DGS-2205) and instantly got internet connectivity. Note that this switch is plugged into the aforementioned Netgear router.For good measure, I tried power-cycling the router and laptop.
BTW - I can connect the laptop to the router wirelessly but I am trying to make use of the faster transfer speed of the ethernet connection.
My net drops off every 20secs like clockwork, only affecting the wireless.I bought a new router yesterday to see if that would work, but it hasn't. At the moment, my router is connected to the modem, and my computer upstairs is running through the wireless connection from the router (not the modem)
My router is a NetGear N600 Wireless Dual Band... and my modem is a NetGear Rangemax wireless My computer is running Windows 7 and has a Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Network Adapter(im connecting to my network via the 2.4ghz... not the 5ghz)I've tried doing the whole, ipconfig/ release
I previously had DSL with my own combo modem/wireless router. I cancelled DSL and got Cable broadband instead. I've already unplugged my DSL modem/router and have my cable modem hooked up, all is running well. I bought a new Netgear N600 wireless router that I want to set up. Do I have to uninstall any software or files from my previous DSL modem/router before installing my new cable router?
View 3 Replies View RelatedI have internet through my cable company and currently use their wireless netgear router. I purchased a Netgear Router N600 but it does not have a port for the cable connection. Can you recommend the correct wireless router
View 1 Replies View Relatedwhat is the WI-fI Network name (SSID) and Network Key (password) of my Netgear N600 Wireless Dual Band Router WNDR3400v2
View 1 Replies View RelatedHow do I change the UPnP setting on my router?
View 2 Replies View Related
