i'm having problem to ping succesfully default gateway on Router1 from Router2. Basically i can: - ping from R1 the serial interface on R2 and default gateway on R2 - telnet from R1 to R2 - ping from R2 to serial link on R1, BUT I CANNOT ping default gateway from R2 to R1 Below is the photo showing topology and running configuration on both routers
View 2 RepliesI have a VM server, whose IP is in customer VLAN600 ( 172.60.60.10/24 ) and Peer end is switch then Firewall.Switch is configured with same VLAN600 and learning mac-address of Server on VLAN 600, Firewall is also having VLAN600 and IP is 172.60.60.1/24.Server is not able to Ping/reach Firewall and vice versa.
View 1 Replies View RelatedI'm trying to get a 2811 router with a NM-AIR-WLC6 Wireless Controller Module to work with an c1200 series access point. The LWAP is connected to a 2690 switch which has a trunk connected to the router. My configuration looks very similar to example 2 on this page: [URL] . The LWAP does get an IP from the DHCP pool on the router. I can also connect to the GUI of the controller from a PC on VLAN 250 (which also is connected to the switch).
[URL]
The moment I join my Wireless network I get no IP and when I enter a valid static IP, I still can't ping the gateway. I also noticed that the controller could ping the gateway before I configured the interface. After configuring an interface with that gateway, the controller loses the ability to ping to it. I can't seem to figure out why. I've been working all week on getting this controller and LWAP to broadcast a fully working network.
This would probably sound like a stupid question but it took at least 2 hours of my time so far. I have a 3750 switch where a router and a server is connected. From the switch I can ping the router and server with no issue (directely connected). But from the server I am not able to ping the router. The router and the server are in the same subnet. The router is configured as the default router for the server. I am not able to ping the server from the router either. Here's the output of the ip route from the router. The server IP address is 10.1.200.21 and the router IP address is 10.10.200.1
10.0.0.0/8 is variably subnetted, 8 subnets, 3 masks
C 10.1.30.0/24 is directly connected, FastEthernet0/0.30
C 10.1.20.0/24 is directly connected, FastEthernet0/0.20
[Code].....
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies View RelatedI used the Cisco Configuration Professional to add an Easy VPN Server to my 3825. I'm able to connect when remote but I can't ping the default gateway of 192.168.1.1 which is in the same network as the VPN DHCP pool. I can access every single other device on the VLAN segments but not the default gateway which means when i connect I can't look at my router. And there's more, I cannot ping anything offnet (ie 75.75.75.75).
Attached are some images which show some details from the client during the VPN connect and a few from the router (i had to use the lan switch as a jump host). If you can figure this out before I go back to the coffee shop to test this tomorrow I will send you a cake.
[code]...
about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies View RelatedI have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
I have a 3560G and an ASA FW, for which I am trying to use PBR to append the next hop. The gateway is the switch VLAN address and the amended net hop is the same VLAN interface on the ASA. Trouble is, I can ping the FW from a client, but not the switch. If I remove the route map, I can ping both. Even more strange is this is the case for some VLANs, but not all!
Config:
HOST ON VLAN 96
IP 10.11.120.99
S/M 255.255.255.240
[Code].....
Loss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies View RelatedMy controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies View RelatedWe have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View Relatedi joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies View RelatedPeriodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
I recently got a new laptop and ever since, the internet goes in and out. Most of the time it is not out long enough to display the no connectivity icon or stop music from streaming but it is noticeable. When I run the troubleshooter it says that the default gateway is unavailable. I tried manually setting the connection information but the same thing keeps happening except the troubleshooter then says that DHCP is not enabled. I've disabled every firewall I can find and updated all the drivers available. Here is my info:[CODE]
View 3 Replies View RelatedI am trying to get rid of 2 old 2651xm's and 2 2950's from my CCNA days and want to get into the ASA realm. Can I be able to use the ASA, not only as a security appliance / firewall, but also be able to write the access lists, etc, to be able to use this as my router to push packets to and from my internal LAN to the outside world? I guess I should have stated as this being the front end device to my network, just after my DSL Cable modem, that is..and being the only device. I am trying to have this as my main router /firewall solution and then I have an old Linksys router I will pipe off one of the L2 ports to have an AP for my wireless devices? Is this a real solution an ASA can provide?
View 2 Replies View RelatedWe have a network consisting of a central site and a few remote offices. The sites are all connected via MPLS and also have VPNs over ADSL / internet connections as a backup. The remote offices have Cisco 837 routers for the ADSL connections which we can manage but the MPLS routers are managed by the service provider providing the MPLS connections. At the central site we have a Cisco 891 for the the MPLS connection (which we manage) and a Cisco ASA5505 for the backup VPNs.
In order to implement failover from MPLS to VPN in the event of any MPLS line going down I have tried to use ip sla monitors and tracked objects on the 891 as per Cisco's documentation. The problem that I am finding is that I can't set the number of ICMP echo failures required before the tracked route is dropped. Whenever the ip sla monitor fails to get a response the tracked route is dropped immediately. This is too sensitive as packets are occasionally dropped which results in the routes bouncing back and forth between MPLS and VPN too frequently (disconnecting users in the process).
I have tried different threshold types and values, tried configuring ip sla monitor reaction-triggers (although I don't understand what little documentation that I can find on this) and have even looked at event manager. I have been working on this for a few weeks now and am getting nowhere.
The Cisco ASA5505's implementation of ip sla monitor is much better in that it is possible to specify the number of packets but unfortunately we can't use the ASA as the default gateway for the LAN as the asymmetrical routing that occurs does not work with the firewall function of the ASA.
Any issue with ip sla monitor on IOS and managed to get it working?
When I plug my laptop up to our modem, all i get is local access. IPconfig gives me to default gateway or dns suffix. Naturally there is no wireless. My roomates laptop runs fine wired or not and we have the same set up.Not sure what to do.
View 12 Replies View RelatedI am having issues playing certain games on my ps3. So I've been searching for solutions and I came across a video that wanted me to go to run/cmd/ipconfig. I have little knowledge of computers but I'm not sure that what my ipconfig is showing is supposed to be there. At first I googled and learned about ipv6 addresses because i found that weird but i think that checks out fine. I then googled about the weird numbers and letters in my default gateway and came up empty. Is there a reason thats there?
View 3 Replies View RelatedI have Squid proxy installed on a ubuntu box here. Currently all my PC's use my ADSL modem as their default gateway but what i wanted to do was see if it was possible to use the ubuntu box as the default gateway, and have it route through Squid to my ADSL modem.
View 3 Replies View RelatedI am trying to change the password on my D-Link router. So i typed ipconfig into cmd and the default gateway i get is 169.234.95.I have tried what used to work at home such as 192.168.0.1 and all of those.
View 9 Replies View Relatedcannot connect to my default gateway 192.168.1.1 frustrating.
View 1 Replies View RelatedBasically, I'm using a broadband modem, which appears to be connecting fine, with all the required lights being on. My ISP says that, from their end, everything is perfect. Even my laptop shows Local Area Network as connected.However, for some reason, I am not able to access the internet. I was able to use it till last evening, but suddenly the internet stopped working. On Google Chrome, it says that there is no DNS or something.Subsequently, when I tried to access my modem settings, it shows as 'webpage not available'. I then noticed that there is no default gateway! I was able to access it the day before, but now I can't.
View 10 Replies View Relatedi recently had to do a 30/30/30 reset to my Linksys WRT150N which has DD-WRT installed on it... I can't access the configuration settings on the router by typing in 192.168.1.1. I did IPCONFIG/ALL and couldn't nothing came up for Default Gateway.
View 4 Replies View RelatedIt only happens with 1of my laptops, all others have not problems. In the network and sharing ctr, it intermittently says Access type: internet then suddenly I get a no internet access. I've tried release renew DNS, reboot computer, release/renew IP. When it says I have internet access, I attempt to connect to no avail.
View 7 Replies View RelatedI'm really not clear about default-gateway on switch command, not the function but how its works.i have 1 multilayer switch (MLS 1) that have 2 vlan within it, vlan 2 and 100. on vlan 2 i assign ip address of 192.168.1.1 and on vlan 100 is 172.16.1.254. both vlans are up. then under that multilayer switch i added 2 more MLS (MLS 2 and MLS 3), and the links of MLS 2 and 3 to MLS 1 are trunking. and both MLS 2 and 3 have a same vlan with MLS 1. that i assign an ip address on vlan 2 in MLS 2 192.168.1.2 and i set default gateway 192.168.1.1, and i do the same to MLS 3 but the ip address of vlan 2 is 192.168.1.3i already setup the routing protocol on MLS 1 so that vlan 2 could contact vlan 100. but the fact it doesnt work at all, both MLS 2 and 3 cannot contact vlan 100 eventhough that are already have default-gateway setup, is there anything wrong with the configuration ??
View 3 Replies View RelatedWhy it makes problems to use a default route on a BGP-router (cisco 6500 with sup720 3bxl).Only a very few amount of hosts have that kind of problem and the 50% paket loss is only between this hosts. So another host has no loss to any of the affected hosts. looks for me like there is a problem in the CEF-table.The router has a BGP-fulltable. The gateway of last resort is only set for cases like a flapping BGP-route, so that the traffic is sent to a default next hop, because sometimes he knows a better route which isnt flapping.
View 1 Replies View RelatedWe have an ASA 5510, with two internet connections. One inteded for VPN l2l and the other for general users inet access.
On asa 8.04, I configured the crypto map on inteface "VPNAccess" and a static route to the L2L remote peer through VPN internet access, the default rotue was pointing the general inet router.
We bought a new firewall with 8.4.1, and now asa only tries to initiate traffic if remote peer is on the default gateway.
It ignores more specific routes (i mean longer masks) and always tries to use default gateway, but only for VPN, if I make a trace route for that peers it uses correctly the routing table.
Is it possible to create a site-to-site ipsec vpn (lab environment) between two 5505's (ASA IOS 8.2(5) & asdm-645-206) with the same default gateway. I.E. a back to back site-to-site VPN tunnel or do I need to deploy a router and hang each 5505 off a different interface? We have plenty of public IP's but only one default gateway to our ISP (Internet).
View 2 Replies View RelatedI have RV042 on my remote network, i have problems with VPN connection , user can connect to RV042 but only inside IPs that can ping from vpn user.Is it any way to make the traffic from Rv042 will back to RV042 . maybe with nat.. in example below 192.168.5.100 is my lan IP from my DSL dhcp, and 172.27.0.20 ip on remote, traffic not back to my pc/vpn client, what i want is to translate 192.168.5.100 to RV042 LAN ip address
1485: ICMP echo request (len 32 id 256 seq 29) 192.168.5.100 > 172.27.0.20
1486: ICMP echo reply (len 32 id 256 seq 29) 172.27.0.9 > 192.168.5.100
1487: ICMP echo request (len 32 id 256 seq 30) 192.168.5.100 > 172.27.0.20
1488: ICMP echo reply (len 32 id 256 seq 30) 172.27.0.9 > 192.168.5.100
[code]....
I rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
View 3 Replies View RelatedMy ISP is changing out all the ADSL routers in our area and they have blocked the Default Gateway Address, so we can not access it via Web Browser. This is frustrating because they changed our Wi-Fi password, instead of just keeping what we had like an Einstein. They said they did it because of Hackers
View 2 Replies View Related