Cisco :: Default - Gateway On Switch Command
Mar 27, 2013
I'm really not clear about default-gateway on switch command, not the function but how its works.i have 1 multilayer switch (MLS 1) that have 2 vlan within it, vlan 2 and 100. on vlan 2 i assign ip address of 192.168.1.1 and on vlan 100 is 172.16.1.254. both vlans are up. then under that multilayer switch i added 2 more MLS (MLS 2 and MLS 3), and the links of MLS 2 and 3 to MLS 1 are trunking. and both MLS 2 and 3 have a same vlan with MLS 1. that i assign an ip address on vlan 2 in MLS 2 192.168.1.2 and i set default gateway 192.168.1.1, and i do the same to MLS 3 but the ip address of vlan 2 is 192.168.1.3i already setup the routing protocol on MLS 1 so that vlan 2 could contact vlan 100. but the fact it doesnt work at all, both MLS 2 and 3 cannot contact vlan 100 eventhough that are already have default-gateway setup, is there anything wrong with the configuration ??
View 3 Replies
ADVERTISEMENT
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Nov 1, 2012
We have a 3560 switch behind a ASA 5510 at a site that we are trying to access via telnet over the internet, we find out the switch does not have a default gateway configured. So I configure the following rule on the 5510: [code] Try accessing the switch, and all is good. One of our change control steps is to identify any others are connected to the device via: [code] I see the connection and show users command return 172.16.30.15, as expected. How is it possible that address can connect to that switch.
View 7 Replies
View Related
Aug 25, 2012
I had setup a lan infrastructure with 5 3750 stack swithes. In these 3 of them are in one stack which is acting as access switch, 2 of them in another stack which is as core switch where all the SVI is configured. Now, when i tried to ping from our edge pc which is connected in access switch to default gaeway, which is configured in core switch, the ICMP is getting delayed . But when try to ping from the same edge pc to another user PC, it is getting less tahn 1 millisecond icmp replies.
why icmp is delaying to default gateway , but working with another edge to edge pcs without any delays?
View 1 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Jun 5, 2013
I have an 877 router which has a DSL WAN interface. The DSL service at this site is unreliable, so the company have purchased a separate 3G router to be used as a backup. This device maintains 3G connectivity at all times and has a static IP on the internal subnet (for arguments sake let's say 10.0.0.253).
What I want to do with the Cisco router is to track the DSL interface and if it is up, install a default route pointing to it. If it is down, I want the default route to be the 3G router.
I am thinking the best way to do this is to set up a track and then set 2 default routes; one which is installed if the tracking is up, the other has a higher admin distance and points to the 3G router and thus should only be used if the track is down. For example:
track 10 interface Dialer0 ip routing
delay down 30 up 30
ip route 0.0.0.0 0.0.0.0 Dialer0 track 10
ip route 0.0.0.0 0.0.0.0 10.0.0.253 100
Is this likely to work or is there a better way to do it?
View 7 Replies
View Related
Apr 18, 2013
I have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
View 4 Replies
View Related
Feb 21, 2013
i joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies
View Related
May 3, 2012
Periodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
View 14 Replies
View Related
Nov 30, 2011
I recently got a new laptop and ever since, the internet goes in and out. Most of the time it is not out long enough to display the no connectivity icon or stop music from streaming but it is noticeable. When I run the troubleshooter it says that the default gateway is unavailable. I tried manually setting the connection information but the same thing keeps happening except the troubleshooter then says that DHCP is not enabled. I've disabled every firewall I can find and updated all the drivers available. Here is my info:[CODE]
View 3 Replies
View Related
Mar 28, 2012
I am trying to get rid of 2 old 2651xm's and 2 2950's from my CCNA days and want to get into the ASA realm. Can I be able to use the ASA, not only as a security appliance / firewall, but also be able to write the access lists, etc, to be able to use this as my router to push packets to and from my internal LAN to the outside world? I guess I should have stated as this being the front end device to my network, just after my DSL Cable modem, that is..and being the only device. I am trying to have this as my main router /firewall solution and then I have an old Linksys router I will pipe off one of the L2 ports to have an AP for my wireless devices? Is this a real solution an ASA can provide?
View 2 Replies
View Related
Feb 13, 2013
i'm having problem to ping succesfully default gateway on Router1 from Router2. Basically i can: - ping from R1 the serial interface on R2 and default gateway on R2 - telnet from R1 to R2 - ping from R2 to serial link on R1, BUT I CANNOT ping default gateway from R2 to R1 Below is the photo showing topology and running configuration on both routers
View 2 Replies
View Related
Mar 16, 2011
We have a network consisting of a central site and a few remote offices. The sites are all connected via MPLS and also have VPNs over ADSL / internet connections as a backup. The remote offices have Cisco 837 routers for the ADSL connections which we can manage but the MPLS routers are managed by the service provider providing the MPLS connections. At the central site we have a Cisco 891 for the the MPLS connection (which we manage) and a Cisco ASA5505 for the backup VPNs.
In order to implement failover from MPLS to VPN in the event of any MPLS line going down I have tried to use ip sla monitors and tracked objects on the 891 as per Cisco's documentation. The problem that I am finding is that I can't set the number of ICMP echo failures required before the tracked route is dropped. Whenever the ip sla monitor fails to get a response the tracked route is dropped immediately. This is too sensitive as packets are occasionally dropped which results in the routes bouncing back and forth between MPLS and VPN too frequently (disconnecting users in the process).
I have tried different threshold types and values, tried configuring ip sla monitor reaction-triggers (although I don't understand what little documentation that I can find on this) and have even looked at event manager. I have been working on this for a few weeks now and am getting nowhere.
The Cisco ASA5505's implementation of ip sla monitor is much better in that it is possible to specify the number of packets but unfortunately we can't use the ASA as the default gateway for the LAN as the asymmetrical routing that occurs does not work with the firewall function of the ASA.
Any issue with ip sla monitor on IOS and managed to get it working?
View 2 Replies
View Related
Jan 3, 2011
When I plug my laptop up to our modem, all i get is local access. IPconfig gives me to default gateway or dns suffix. Naturally there is no wireless. My roomates laptop runs fine wired or not and we have the same set up.Not sure what to do.
View 12 Replies
View Related
Feb 8, 2013
I am having issues playing certain games on my ps3. So I've been searching for solutions and I came across a video that wanted me to go to run/cmd/ipconfig. I have little knowledge of computers but I'm not sure that what my ipconfig is showing is supposed to be there. At first I googled and learned about ipv6 addresses because i found that weird but i think that checks out fine. I then googled about the weird numbers and letters in my default gateway and came up empty. Is there a reason thats there?
View 3 Replies
View Related
Jan 2, 2011
I have Squid proxy installed on a ubuntu box here. Currently all my PC's use my ADSL modem as their default gateway but what i wanted to do was see if it was possible to use the ubuntu box as the default gateway, and have it route through Squid to my ADSL modem.
View 3 Replies
View Related
May 20, 2011
I am trying to change the password on my D-Link router. So i typed ipconfig into cmd and the default gateway i get is 169.234.95.I have tried what used to work at home such as 192.168.0.1 and all of those.
View 9 Replies
View Related
Sep 10, 2012
I have a VM server, whose IP is in customer VLAN600 ( 172.60.60.10/24 ) and Peer end is switch then Firewall.Switch is configured with same VLAN600 and learning mac-address of Server on VLAN 600, Firewall is also having VLAN600 and IP is 172.60.60.1/24.Server is not able to Ping/reach Firewall and vice versa.
View 1 Replies
View Related
Dec 18, 2012
cannot connect to my default gateway 192.168.1.1 frustrating.
View 1 Replies
View Related
May 8, 2011
Basically, I'm using a broadband modem, which appears to be connecting fine, with all the required lights being on. My ISP says that, from their end, everything is perfect. Even my laptop shows Local Area Network as connected.However, for some reason, I am not able to access the internet. I was able to use it till last evening, but suddenly the internet stopped working. On Google Chrome, it says that there is no DNS or something.Subsequently, when I tried to access my modem settings, it shows as 'webpage not available'. I then noticed that there is no default gateway! I was able to access it the day before, but now I can't.
View 10 Replies
View Related
Feb 7, 2012
i recently had to do a 30/30/30 reset to my Linksys WRT150N which has DD-WRT installed on it... I can't access the configuration settings on the router by typing in 192.168.1.1. I did IPCONFIG/ALL and couldn't nothing came up for Default Gateway.
View 4 Replies
View Related
Sep 17, 2012
It only happens with 1of my laptops, all others have not problems. In the network and sharing ctr, it intermittently says Access type: internet then suddenly I get a no internet access. I've tried release renew DNS, reboot computer, release/renew IP. When it says I have internet access, I attempt to connect to no avail.
View 7 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Mar 22, 2013
Why it makes problems to use a default route on a BGP-router (cisco 6500 with sup720 3bxl).Only a very few amount of hosts have that kind of problem and the 50% paket loss is only between this hosts. So another host has no loss to any of the affected hosts. looks for me like there is a problem in the CEF-table.The router has a BGP-fulltable. The gateway of last resort is only set for cases like a flapping BGP-route, so that the traffic is sent to a default next hop, because sometimes he knows a better route which isnt flapping.
View 1 Replies
View Related
Jun 19, 2011
We have an ASA 5510, with two internet connections. One inteded for VPN l2l and the other for general users inet access.
On asa 8.04, I configured the crypto map on inteface "VPNAccess" and a static route to the L2L remote peer through VPN internet access, the default rotue was pointing the general inet router.
We bought a new firewall with 8.4.1, and now asa only tries to initiate traffic if remote peer is on the default gateway.
It ignores more specific routes (i mean longer masks) and always tries to use default gateway, but only for VPN, if I make a trace route for that peers it uses correctly the routing table.
View 12 Replies
View Related
Jan 4, 2012
Is it possible to create a site-to-site ipsec vpn (lab environment) between two 5505's (ASA IOS 8.2(5) & asdm-645-206) with the same default gateway. I.E. a back to back site-to-site VPN tunnel or do I need to deploy a router and hang each 5505 off a different interface? We have plenty of public IP's but only one default gateway to our ISP (Internet).
View 2 Replies
View Related
Apr 11, 2012
I have RV042 on my remote network, i have problems with VPN connection , user can connect to RV042 but only inside IPs that can ping from vpn user.Is it any way to make the traffic from Rv042 will back to RV042 . maybe with nat.. in example below 192.168.5.100 is my lan IP from my DSL dhcp, and 172.27.0.20 ip on remote, traffic not back to my pc/vpn client, what i want is to translate 192.168.5.100 to RV042 LAN ip address
1485: ICMP echo request (len 32 id 256 seq 29) 192.168.5.100 > 172.27.0.20
1486: ICMP echo reply (len 32 id 256 seq 29) 172.27.0.9 > 192.168.5.100
1487: ICMP echo request (len 32 id 256 seq 30) 192.168.5.100 > 172.27.0.20
1488: ICMP echo reply (len 32 id 256 seq 30) 172.27.0.9 > 192.168.5.100
[code]....
View 3 Replies
View Related
Feb 20, 2012
Can we set ips 4260 into factory default settings with a single command?
View 0 Replies
View Related
Jun 26, 2012
when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies
View Related
Oct 11, 2011
I rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
View 3 Replies
View Related
Feb 23, 2012
My ISP is changing out all the ADSL routers in our area and they have blocked the Default Gateway Address, so we can not access it via Web Browser. This is frustrating because they changed our Wi-Fi password, instead of just keeping what we had like an Einstein. They said they did it because of Hackers
View 2 Replies
View Related
Jan 15, 2013
I've been trying to connect to the internet all day. Every time it connects, but only with limited connectivity. I run troubleshooting, but it doesn't fix the problem. Sometimes it won't have anything to report back other times it says that the default gateway is unavailable. My laptop is the only device in our home that won't connect, so I don't think it's the router.I think the router is a cisco router, there is a cisco box mounted on the ceiling with a cord leading into it (I don't have access to any buttons though)I live in an apartment building with free internet, so I'm not sure who the provider is.
View 11 Replies
View Related
May 12, 2012
I keep dropping off my internet connection and getting this error.
View 11 Replies
View Related
