Cisco Security :: Can Set IP's 4260 Into Factory Default Settings With Single Command
Feb 20, 2012Can we set ips 4260 into factory default settings with a single command?
View 0 Replies
ADVERTISEMENT
Cisco Switches :: How To Set SG200-08P To Factory Default Settings
Oct 18, 2011We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions. We couldn't find any information related to a "factory reset" in that document either. Pressed the "paper clip button" on the switch but we still can't get in.
View 7 Replies View RelatedD-Link DIR-601 :: Upgrading Firmware From 1.0 To 1.02 Will It Default Factory Settings?
Aug 6, 2011I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedCisco Routers :: RVS4000 Necessary To Reset To Factory Default Settings
Feb 15, 2009Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View RelatedCisco Routers :: WRVS4400N - Automatic Revert To Factory Default Settings?
Jan 23, 2013I had something strange happen to my WRVS440N router yesterday. Our network had crashed for some reason. So I attempted to log into the device to see what was wrong and I was surprised to discover that all of the settings including user name and password had reverted back to factory default.
1. What are all of the possible scenarios that would cause this to happen?
2.Would disconnecting power in the middle of a boot up sequence cause the router to revert to factory settings?
Netgear Factory Settings?
Nov 17, 2012I have rebooted my netgear router to the factory settings and now the internet wont work , i have no idea how to get it to work again. On the box all the right lights are green exept the internet light which is red.
View 1 Replies View RelatedFactory Settings For Wireless Routers?
Nov 29, 2011i don't have the cd to set my wireless router back up, so how do I go back to factory setup without it?
View 2 Replies View RelatedCisco :: Series 800 Factory Default Restore?
Feb 1, 2013I'm having trouble with an 800 series router. Work has borrowed it to me so i can practice for my icnd2 exam. Only problem is it has a username and password on it. I have been told i can wipe the device and start over. but i cant get in to the user mode or any mode's as i don't have the user name and password. Is there a way of resetting the router back to factory defaults with out logging in to it?
View 2 Replies View RelatedCisco WAN :: 1800 - Factory Default Reset?
Sep 24, 2012My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
Cisco WAN :: AIR-AP521G-E-K9 / Reset To Factory Default In CLI
Jan 22, 2012I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View RelatedCisco Firewall :: Factory Default On ASA 5520?
Jul 12, 2011I have another asa 5520 and it is configured. when i do factory default every thing erase. ok. when i enter again it promped for enable password. and it takes my privious password taht i gave in full configuration.
It generally comes no password . Why enable PW dont erase ? why factory default holds my previous password ?
D-Link DIR-655 :: Restore To Default Factory?
Nov 19, 2012I wonder how i can restore my router to its defalt settings if my reset button is broken and the router has lock the mac of my pc. Can i connect the router to my pc and access it from it?
View 7 Replies View RelatedCisco Wireless :: 3502i - How To Restore The Factory Settings
Jul 18, 2012The ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,
View 3 Replies View RelatedCisco Infrastructure :: Resetting 2431 IAD To Factory Settings?
Dec 10, 2012I am at the rommon screen getting the > sign
Rommon 1>
When I am typing confreg 0x2142 I am just getting “rommon 2>” and if try again I will get “rommon 3 >”
No reset prompt , this never happened to me
Can't Reset Arris Wtm652 To Factory Settings
May 5, 2011I am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies View RelatedResetting Modem / Router To Factory Settings
Oct 8, 2011Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies View RelatedDell :: Inspiron 15 M5040 - Factory Settings
May 20, 2013Had to so a install back to factory settings now I have no access to Internet, says network controller is missing, have tried downloading drivers but obviously not downloading the right one.
View 2 Replies View RelatedCisco :: 1252 Wireless AP Resetting To Factory Default
Jan 5, 2012I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedCisco Firewall :: Factory Default Config On ASA 5505 With 8.4.1?
May 1, 2011What is the factory default config on ASA5505 with 8.4.1?
View 3 Replies View RelatedCisco Wireless :: Factory-Default Reset For AP3600?
Dec 17, 2012How to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.
View 2 Replies View RelatedCisco Wireless :: 1130 AP Default Factory Setting
Sep 15, 2012Any info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies View RelatedCisco Routers :: WRV210-A V01 Reset To Factory Default?
Oct 30, 2011I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Cisco Firewall :: Bring ASA5550 To Factory Default?
Feb 2, 2012getting step by step procedure to bring an ASA5550 to factory default setting, so that I can configure it from scratch via ASDM
View 3 Replies View RelatedCisco Switches :: ESW 540 / How To Reset Switch To Factory Default
Jun 1, 2011Unable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View RelatedCisco Switching/Routing :: 3750G Won't Factory Default?
Jun 2, 2013I have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
1) Hold mode button & issue a reload after the lights start flashing
2) issue "Write Erase" then issue "reload"
3) issue "Write Erase", then issue "Write", then issue "reload"
4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)
5) issue "erase start" then issue "copy run start" then issue "reload"
Is there a special way to reset a StackMaster back to factory defaults?
Cisco Firewall :: PIX 515E Reset To Factory Default?
Jul 3, 2011Im connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View RelatedCisco Firewall :: Cannot Reset 5505 To Factory Default
Apr 10, 2011i have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedReset DLink Modem To Factory Default?
Jan 2, 2013I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies View RelatedD-Link DIR-655 :: Randomly Resets To Factory Default
Feb 19, 2013My DIR655 is about a month old, works fine but randomly resets to factory default (loses configuration). Used it to get internet from an existing wired connection with gateway 192.168.0.1, therefore changed Network address of Dlink to 192.168.1.1 to make it work. Every so many days of working ok, it suddenly resets to factory default with no one touching the reset button. Have to restore the configuration from saved file which is a hassle.
Although the DIR655 is connected to a UPS, it shouldn't lose the settings during blackouts right?
Cisco Firewall :: Pix 515e To Reset The Device To Factory Settings
Aug 12, 2011I have completed my CCNA qualification and i am doing some volunteering for a none proffit eletronics recyciling company they receved some cisco pix 515e firewalls and i was aloud to keep one so i can learn how hardwaire firewalls work and how to set them up but i can not seem to connect to it is there a way to completely reset the device to factory settings without any ip address or passwords i do not have any cables for the device but i have made a straight and cross over cable and there is a box of cables at the recyciling company from diffrent places if i need a specialist cable i may be able to find one
View 6 Replies View RelatedRestored Computer To Factory Settings And Cannot Connect To The Internet
Oct 10, 2012I just restored my computer (Windows XP) to factory settings and it won't connect to the internet. I'm running an ethernet connection. I tried to look up a solution online but nothing has worked. Also, Im sure its not an issue with the modem, because all the other computers in the office are connecting to the internet just fine. It's only this one computer?
View 5 Replies View RelatedD-Link DIR-655 :: Cannot Access Router Or Reset Factory Settings
Jul 22, 2010My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies View RelatedCisco Wireless :: Reset Aironet 1231 To Factory Default?
Sep 17, 2012I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies View Related