Factory Settings For Wireless Routers?
Nov 29, 2011i don't have the cd to set my wireless router back up, so how do I go back to factory setup without it?
View 2 Replies
ADVERTISEMENT
Cisco Routers :: RVS4000 Necessary To Reset To Factory Default Settings
Feb 15, 2009Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View RelatedCisco Routers :: WRVS4400N - Automatic Revert To Factory Default Settings?
Jan 23, 2013I had something strange happen to my WRVS440N router yesterday. Our network had crashed for some reason. So I attempted to log into the device to see what was wrong and I was surprised to discover that all of the settings including user name and password had reverted back to factory default.
1. What are all of the possible scenarios that would cause this to happen?
2.Would disconnecting power in the middle of a boot up sequence cause the router to revert to factory settings?
Cisco Wireless :: 3502i - How To Restore The Factory Settings
Jul 18, 2012The ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,
View 3 Replies View RelatedWindows 7 - Can't Detect Any Wireless Networks / Restored To Factory Settings
Sep 20, 2012A few hours ago, I just restored my laptop to factory settings. Once it was done, I tried connecting to the internet but the computer could not detect ANY wireless networks!I already know it is not the modem or router because I have a Macbook Pro and two HP laptops that connect perfectly fine to the modem. I also made sure the wireless is on. The laptop with the problem is a Toshiba Satellite l645. It's running on a 64-bit Windows 7. When I try to look up wireless networks, it only shows 'MOBILE BROADBAND CONNECTION".
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersNguyen Family>ipconfig/all
Windows IP Configuration
[code]...
Linksys Wireless Router :: WRT160N - Factory Settings Reset?
Jun 7, 2010How to reset my router to factory settings so i can install it on a new computer
View 2 Replies View RelatedLinksys Wireless Router :: Reset WRT54G2 V1 To Factory Settings?
Dec 29, 2009Iused my installation cd to re-setup my linksys. I moved and used a laptop previously. Now i am at a house that has a desktop. I want to keep the desktop wired and make my laptop wired. So, when i went to re-install it said i had to reset my linksys to factory settings.
View 2 Replies View RelatedDell :: Restored Inspiron N5010 To Factory Settings And No Longer Have Wireless
Jul 11, 2013I installed the drivers that came installed on the PC.
I looked at the settings and confirmed that they were correct per my internet provider.
Enernet works and I can hook up using cable. But the PC used to auto detect all wireless connections available. Now it detects nothing.
Netgear Factory Settings?
Nov 17, 2012I have rebooted my netgear router to the factory settings and now the internet wont work , i have no idea how to get it to work again. On the box all the right lights are green exept the internet light which is red.
View 1 Replies View RelatedCan't Reset Arris Wtm652 To Factory Settings
May 5, 2011I am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies View RelatedResetting Modem / Router To Factory Settings
Oct 8, 2011Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies View RelatedDell :: Inspiron 15 M5040 - Factory Settings
May 20, 2013Had to so a install back to factory settings now I have no access to Internet, says network controller is missing, have tried downloading drivers but obviously not downloading the right one.
View 2 Replies View RelatedRestored Computer To Factory Settings And Cannot Connect To The Internet
Oct 10, 2012I just restored my computer (Windows XP) to factory settings and it won't connect to the internet. I'm running an ethernet connection. I tried to look up a solution online but nothing has worked. Also, Im sure its not an issue with the modem, because all the other computers in the office are connecting to the internet just fine. It's only this one computer?
View 5 Replies View RelatedD-Link DIR-655 :: Cannot Access Router Or Reset Factory Settings
Jul 22, 2010My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies View RelatedD-Link DIR-601 :: Upgrading Firmware From 1.0 To 1.02 Will It Default Factory Settings?
Aug 6, 2011I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedCisco Switches :: How To Set SG200-08P To Factory Default Settings
Oct 18, 2011We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions. We couldn't find any information related to a "factory reset" in that document either. Pressed the "paper clip button" on the switch but we still can't get in.
View 7 Replies View RelatedCisco Infrastructure :: Resetting 2431 IAD To Factory Settings?
Dec 10, 2012I am at the rommon screen getting the > sign
Rommon 1>
When I am typing confreg 0x2142 I am just getting “rommon 2>” and if try again I will get “rommon 3 >”
No reset prompt , this never happened to me
Windows Vista - Reset Router To Factory Settings Now Cannot Configure
Feb 6, 2012I have windows vista, and forgot my network password. I reset my router to factory settings by pushing the reset button on the back.I tried reconfiguring the router from the network icon, but at the end of the process it says it cannot configure my router.I lost my internet service in the process
View 1 Replies View RelatedLinksys Access Point :: WAP54G Won't Reset To Factory Settings
Mar 23, 2013I was having some connectivity issues with my network of WAP54G's, so I had a technician come to have them looked at. The technician turned out to be completely clueless, and he messed up one of the APs in the process. He changed its IP address and apparently updated its firmware, but he didn't write the new address down, so now I can't access its administrator panel. I've tried to retrieve the IP address using the setup CD that came with the AP, but it doesn't even see the AP in my network. I've tried to factory reset the AP by holding the reset button for 10, 30 and 60 seconds and unplugging the power cord, but to no avail. It still doesn't bring up the admin panel when I enter the default IP in the browser. I think I've tried everything I could find on the Internet about this problem that didn't involve cracking the AP open, but none of it has worked.
View 4 Replies View RelatedCisco Firewall :: Pix 515e To Reset The Device To Factory Settings
Aug 12, 2011I have completed my CCNA qualification and i am doing some volunteering for a none proffit eletronics recyciling company they receved some cisco pix 515e firewalls and i was aloud to keep one so i can learn how hardwaire firewalls work and how to set them up but i can not seem to connect to it is there a way to completely reset the device to factory settings without any ip address or passwords i do not have any cables for the device but i have made a straight and cross over cable and there is a box of cables at the recyciling company from diffrent places if i need a specialist cable i may be able to find one
View 6 Replies View RelatedD-Link DIR-615 :: It Freezes Every Night And Reverts To Factory Settings When Power-cycled
Dec 4, 2011Our DIR-615 has started freezing and when reset (power cycled), it reverts to factory settings.This has been running 24/7 for several months with no problem. Three days in a row now I've woken up to find our home network is down and the DIR-615 status lights are "yellow". Power cycling the DIR615 resolves the problem however the DIR-615 looses its settings, reverting to factory defaults (looses the admin password, wireless settings, etc). I can reload the settings from a file saved on my computer but needless to say, this is a bit annoying. I don't believe there are any wireless clients connected at the time as most of the wireless is served by an airport two floors up. There are several wired devices always connected:
a Zoom ATA carrying our "land line"
a tivo (doing whatever tivo boxes do)
a SSL based Voip phone (different than the zoom ata)
an AirPort Express 802.11n (bridge mode) which may have a couple of wireless clients
a laptop which may or may not be sleeping at the time
There are a couple of ethernet switches in the network.Some of the devices acquire addresses via DHCP, others are assigned fixed addresses outside the range of the DHCP addresses served by the DIR-615.Nothing has changed on the network in months.
The only settings I've messed with on the DIR-615 are:
a) set the admin/user passwords
b) Set the wireless network name, enable WPA, set the WPA Key
c) enabled ntp (this is now disabled and I've set the time manually)
d) Change the network base from 192.168.0. to 192.168.4.
The DIR-615 is hardware rev E3, Firmware 5.10 The cable modem (from RCN) is a Scientific American model DPC2100R2
Cisco Security :: Can Set IP's 4260 Into Factory Default Settings With Single Command
Feb 20, 2012Can we set ips 4260 into factory default settings with a single command?
View 0 Replies View RelatedBelkin Routers :: N150 How To Factory Reset
Dec 29, 2012What buttons, in specific order, do i press to reset my router? i used to know how but can no longer find that info
View 2 Replies View RelatedBelkin Routers :: 300n Cannot Log Into 192.168.2.1 / Cannot Factory Reset / Seem To Be Stuck
Mar 14, 2013I upgraded my internet connection through charter and they shipped a new modem. Installed my new modem and my 300n will not connect to it. So in my attempts to figured things out I went it in and set it up as an access point only. I can access the internet on my desktop but there is no wireless signal in the house. Cannot connect to 192.168.2.1 now either. Tried the manual reset to factory defaults with no luck. At this point all I get is the small flashing blue light and the tall skinny light is not on at all.
View 5 Replies View RelatedCisco Routers :: WRV210 Resets To Factory Defaults?
Sep 23, 2010I purchased a WRV210. I configure the device, setup all my tunnels, WAN, LAN, Wirelss, Security, etc. and within 48 hours it "automatically" resets itself back to "out of the box" settings. This has happened twice now - once after it ran for about 4 days and the second time after only 5 or so hours of opperation.
Is this a known issue with the device? Is there an update I need to apply? I'd give ya my current FW version but I cannot login as it appears to have rest once again lol - and my tunnels are down so no remote access.
I made a backup of the config after the first unscheduled reset - (.bin file) so I have my settings ready to restore.
Cisco Routers :: WRV210-A V01 Reset To Factory Default?
Oct 30, 2011I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Belkin G Wireless CC7A57 - Can't Access Routers Settings
Jul 23, 2011Earlier today I put in a password for my Belkin_G_Wireless_CC7A57 router. I had to change something, im not sure what it was. it was like WPA or WAP. now it wont let me go to my router settings 192.168.2.1 in the address bar is how i have been getting to it. now it just takes me to a OOPS google chrome cannot open this web page..... I just want to restore the router to it factory default settings. it will let this laptop on and another one in the house but not an older one we have which runs Windows XP. If i can get to my router settings i will be fine..
View 2 Replies View RelatedHow To Set Up Routers Qos Settings
Dec 17, 2011I have posted on other sites as well everyone says to use Qos but they dont tell me how.I would just like to be able to limit my brothers bandwidth not just programs. We both use laptops, I use Ethernet, he uses wifi. My router does not have a wifi speed setting. I have tried multiple times to try and set up Qos on my own but it has not worked at all
View 1 Replies View RelatedRouters / Switches :: How To Change IP Filter Settings
Jul 5, 2011For some port fowarding reasons I have to change my router setting to these:Maximum Ports: 4096TCP Timeout (in seconds): 600UCP Timeout (in seconds): 120I am using a Realtek router ( Family PCI-E Gigabit Ethernet <NDIS 6.20>)This is supposed to be EXTREMELY easy but I lack any general computer knowledge whatsoever. In laymen's term, I am N00B.
View 1 Replies View RelatedUpdate The IP Addresses In Routers Configuration Settings?
Jul 24, 2012How do I updat the IP address in my routers configuration?
View 1 Replies View RelatedRouters / Switches :: Cannot Open Router Settings
Feb 22, 2011I cannot open router settings... I had recently opened some ports on my router. However today I tried to access the settings and all it does is a web search for the gateway (192.168.1.254). The internet is working. I reset the router and it did not work. I cannot do a hard reset because I will lose all my settings for my company's settings. Also the router is a Netopia modem/router
View 2 Replies View RelatedBelkin Routers :: Can't Get To Settings Page On N150
Feb 25, 2013After our ISP had a network outage, our Belkin N150 stopped working properly & now I can't get to the Settings page to fix anything. I have used the Reset feature to no avail. The blue light is on but the "Fixit" feature only comes up with something about the ASDL line.
View 1 Replies View RelatedBelkin Routers :: F9K1103V1 - Configuration Settings?
Nov 8, 2012I have tried every which way to configure my model F9K1103V1. It is either impossible or beyond my level of expertise.
View 1 Replies View Related