D-Link DIR-601 :: Upgrading Firmware From 1.0 To 1.02 Will It Default Factory Settings?
Aug 6, 2011
I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies
ADVERTISEMENT
Oct 18, 2011
We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions. We couldn't find any information related to a "factory reset" in that document either. Pressed the "paper clip button" on the switch but we still can't get in.
View 7 Replies
View Related
Feb 15, 2009
Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies
View Related
Sep 16, 2010
I just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
View 9 Replies
View Related
Feb 20, 2012
Can we set ips 4260 into factory default settings with a single command?
View 0 Replies
View Related
Jan 23, 2013
I had something strange happen to my WRVS440N router yesterday. Our network had crashed for some reason. So I attempted to log into the device to see what was wrong and I was surprised to discover that all of the settings including user name and password had reverted back to factory default.
1. What are all of the possible scenarios that would cause this to happen?
2.Would disconnecting power in the middle of a boot up sequence cause the router to revert to factory settings?
View 1 Replies
View Related
Nov 19, 2012
I wonder how i can restore my router to its defalt settings if my reset button is broken and the router has lock the mac of my pc. Can i connect the router to my pc and access it from it?
View 7 Replies
View Related
Feb 19, 2013
My DIR655 is about a month old, works fine but randomly resets to factory default (loses configuration). Used it to get internet from an existing wired connection with gateway 192.168.0.1, therefore changed Network address of Dlink to 192.168.1.1 to make it work. Every so many days of working ok, it suddenly resets to factory default with no one touching the reset button. Have to restore the configuration from saved file which is a hassle.
Although the DIR655 is connected to a UPS, it shouldn't lose the settings during blackouts right?
View 1 Replies
View Related
Jul 22, 2010
My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies
View Related
Dec 4, 2011
Our DIR-615 has started freezing and when reset (power cycled), it reverts to factory settings.This has been running 24/7 for several months with no problem. Three days in a row now I've woken up to find our home network is down and the DIR-615 status lights are "yellow". Power cycling the DIR615 resolves the problem however the DIR-615 looses its settings, reverting to factory defaults (looses the admin password, wireless settings, etc). I can reload the settings from a file saved on my computer but needless to say, this is a bit annoying. I don't believe there are any wireless clients connected at the time as most of the wireless is served by an airport two floors up. There are several wired devices always connected:
a Zoom ATA carrying our "land line"
a tivo (doing whatever tivo boxes do)
a SSL based Voip phone (different than the zoom ata)
an AirPort Express 802.11n (bridge mode) which may have a couple of wireless clients
a laptop which may or may not be sleeping at the time
There are a couple of ethernet switches in the network.Some of the devices acquire addresses via DHCP, others are assigned fixed addresses outside the range of the DHCP addresses served by the DIR-615.Nothing has changed on the network in months.
The only settings I've messed with on the DIR-615 are:
a) set the admin/user passwords
b) Set the wireless network name, enable WPA, set the WPA Key
c) enabled ntp (this is now disabled and I've set the time manually)
d) Change the network base from 192.168.0. to 192.168.4.
The DIR-615 is hardware rev E3, Firmware 5.10 The cable modem (from RCN) is a Scientific American model DPC2100R2
View 12 Replies
View Related
Oct 19, 2011
I upgraded the firmware per one suggestion, but no difference.I am going thru the setup wizard with ethernet cable attached. I want to use them wirelessly so I clicked wireless setup, and entered my network info. At that point I get an error message saying it failed to save settings. I know the ID and password are correct.I have tried exiting the setup wizard and accessing the camera thru the web interface. All wireless settings are correct. The camera works FINE on web browser, myDlink, and even my iPhone app as long as the ethernet cable is attached.Other wireless devices have no trouble connecting to my router. Is there some setting on the router that can be preventing the connection? I've done some trial-and-error changes, like different ports and enabling/disabling UpNp on both camera and router.Oh and almost forgot to mention.I did call tech support, which was a joke. Some foreign lady was reading off a script that told me to reset, unplug, reboot everything. Then she gave me a case# and said upgrade the firmware.
View 11 Replies
View Related
Mar 21, 2011
Cannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
View 4 Replies
View Related
Jun 17, 2011
Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1.URL
View 3 Replies
View Related
Mar 22, 2013
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies
View Related
Dec 19, 2011
What would cause my Dir-825 to magically revert to it's default settings? This is the 4th time this has happened.We rely on a Verizon Network Extender for phone service. It requires an internet connection to function. When the router brain-farts, we don't have phone service... and we don't know it until we try to call out, or try to use the internet. We went to bed last night with the router working and woke up to it not working. It's just my wife and I here. I haven't seen the dog showing any interest in jacking with our computer gear.
When I access the setup utility and go to Manual Wireless Network Setup, the Wireless Network Name has defaulted to dlink, and Security Mode is None. I have to re-enter my personalized setup info, (because that is what our computers are looking for), then all works fine again.I'm a savy XP user, my wife has Vista (yuk) (she doesn't know any better; her daughter installed it).We are Comcast customers. We own a Linksys CM-100 modem. (When I connect direct by hardwire, (i.e. bypass the Dir-825 router), from the modem to any computer, or the Verizon Network Extender, they function just fine. Setup utility for Dir-825 says we have Hardware Version B-1; Firmware Version 2.02NA.
Set Firewall settings to Endpoint Independent for TCP and UDP. I see other posts addressing similar issues of reversion to default settings... but there don't seem to be any clear resolutions of these issues. On 2010-03-11, gunrunnerjohn posted, "I think there may be a shadow file that's actually in the FLASH that needs to get written back to make the changes stick. I seem to recall there is a command to sync the RAMDISK copies to the FLASH." Yet there is no more to this thread.
View 3 Replies
View Related
Aug 11, 2012
I've been lagging really bad when my sister uses the laptop upstairs with wireless connection. Just 1 computer makes me have up to 100 ping, imagine 3. How can configure my settings so that i will stop lagging or configure so that i have priority.I have a Dlink 655 Version A4 with the latest firmware 1.35
View 9 Replies
View Related
Jul 19, 2011
I just flashed this router with DD-WRT about a week ago inside the webui that was provided. It all went well but I wanted to go back to the original factory firmware so turned it off for 20 seconds, and held the reset button for 10 seconds to reach the emergency-room. I re-flashed it with the firmware I got from d-links website and all went well. So I tried to go to 192.168.0.1 that did not work so I tried the ip that I gave it before it was flashed and it still remained x.x.x.254. I also turned off dhcp server since my isp's modem provides that and other services. But when I looked into the logs it would keep starting up dhcp server every minute which would lead to all kinds of problems.
Edit: The ip/subnet are set to 192.168.0.1/255.255.255.0. It seems to start this as soon as dhcp is disabled.
LOG:
11:56:02 device_lan_ip=, device_lan_subnet_mask=
11:56:02 DHCP Server Start
11:55:51 device_lan_ip=, device_lan_subnet_mask=
11:55:51 DHCP Server Start
11:55:40 device_lan_ip=, device_lan_subnet_mask=
11:55:40 DHCP Server Start
Hardware Version listed in the webui: _auth_m
View 5 Replies
View Related
Sep 10, 2011
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies
View Related
Mar 22, 2013
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : V2
ISP : Reliance netconnect Vendor (ZTE Model AC2736) CDM
Region : India
Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged.
View 1 Replies
View Related
Nov 17, 2012
I have rebooted my netgear router to the factory settings and now the internet wont work , i have no idea how to get it to work again. On the box all the right lights are green exept the internet light which is red.
View 1 Replies
View Related
Nov 29, 2011
i don't have the cd to set my wireless router back up, so how do I go back to factory setup without it?
View 2 Replies
View Related
May 5, 2011
I am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies
View Related
Oct 8, 2011
Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies
View Related
May 20, 2013
Had to so a install back to factory settings now I have no access to Internet, says network controller is missing, have tried downloading drivers but obviously not downloading the right one.
View 2 Replies
View Related
Jan 2, 2013
I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies
View Related
Feb 1, 2013
I'm having trouble with an 800 series router. Work has borrowed it to me so i can practice for my icnd2 exam. Only problem is it has a username and password on it. I have been told i can wipe the device and start over. but i cant get in to the user mode or any mode's as i don't have the user name and password. Is there a way of resetting the router back to factory defaults with out logging in to it?
View 2 Replies
View Related
Sep 24, 2012
My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
View 5 Replies
View Related
Jan 22, 2012
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies
View Related
Jul 12, 2011
I have another asa 5520 and it is configured. when i do factory default every thing erase. ok. when i enter again it promped for enable password. and it takes my privious password taht i gave in full configuration.
It generally comes no password . Why enable PW dont erase ? why factory default holds my previous password ?
View 7 Replies
View Related
Oct 10, 2012
I just restored my computer (Windows XP) to factory settings and it won't connect to the internet. I'm running an ethernet connection. I tried to look up a solution online but nothing has worked. Also, Im sure its not an issue with the modem, because all the other computers in the office are connecting to the internet just fine. It's only this one computer?
View 5 Replies
View Related
Jul 18, 2012
The ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,
View 3 Replies
View Related
Dec 10, 2012
I am at the rommon screen getting the > sign
Rommon 1>
When I am typing confreg 0x2142 I am just getting “rommon 2>” and if try again I will get “rommon 3 >”
No reset prompt , this never happened to me
View 1 Replies
View Related
Jan 5, 2012
I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies
View Related
